The Initial Setup Before Using The Unit - JVC XV-SA600BK Instructions Manual

The initial setup before using the unit

We recommend you to set the display language, TV monitor type, analog audio output and digital output before using
the unit, depending on circumstances, by following the procedure below.
When turning on the unit for the first time, the DVD PLAYER SET UP display automatically appears. In such a case,
perform the following procedure from step 2.
See "Changing the initial settings" on and after page 56 for details about each setting item.
1
Press and hold down CHOICE for a few
seconds to bring up the first page of the DVD
PLAYER SET UP display.
The pull-down menu of the "ON SCREEN
LANGUAGE" is already open.
DVD PLAYER SET UP
MENU LANGUAGE
AUDIO LANGUAGE
SUBTITLE
ON SCREEN LANGUAGE
SELECT USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER TO EXET, PRESS CHOICE.
ON SCREEN LANGUAGE selection
2
Use 5/∞ to select a desired language.
You can select the on-screen language for the
preference displays, etc. from among English,
Spanish and French.
3
Press ENTER.
The second page is shown, in which the pull-down
menu of the "MONITOR TYPE" is already open.
DVD PLAYER SET UP
MONITOR TYPE
PROGRESSIVE MODE
SCREEN SAVER
MP3/JPEG
SELECT USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
ENTER TO EXET, PRESS CHOICE.
ENTER
CHOICE
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
SPANISH
FRENCH
4:3 L.B.
16:9 NORMAL
AUTO
16:9 AUTO
4:3 LB
ON
4:3 PS
MP3
MONITOR TYPE selection
TV DVD
STANDBY/ON
OPEN/
CLOSE TV DVD
TV1 TV2 TV3
1 2 3
TV4 TV5 TV6
4 5 6
TV7 TV8 TV9
7 8 9
TV-/-- TV0 MUTING
10 0 +10
TITLE/ TV/VIDEO
RETURN PAGE GROUP CANCEL
CH
+
5/∞
VOL- VOL+
ENTER
CH
-
PREVIOUS NEXT
CLEAR SELECT STROBE
SLOW- SLOW+
REPEAT SUB TITLE AUDIO VFP
fs/Rate PROGRESSIVE
SCAN
DIGEST ANGLE ZOOM
3D
PHONIC AMP VOL
RM-SXV011J
REMOTE CONTROL
4
Use 5/∞ to select a desired monitor type.
You can select the monitor type according to your TV.
• For the normal (conventional) TV, select "4:3 LB"
or "4:3 PS."
• For the wide-screen TV, select "16:9 AUTO" or
"16:9 NORMAL."
See page 59 for details about each mode.
5
Press ENTER.
The third (final) page is shown, in which the pull-
down menu of the "ANALOG OUT" is already
open.
DVD PLAYER SET UP
SELECT
ENTER
6
Use 5/∞ to select a desired analog output
signal type.
You must set this item correctly when you play back
a DVD VIDEO disc recorded with surround
multichannel audio.
• When connecting with a surround decoder, select
"2-CH DOLBY SURROUND."
• When connecting with a stereo amplifier/receiver
or television set, select "2-CH STEREO."
• When connecting the unit's 5.1 channel audio
outputs to an amplifier equipped with 5.1-channel
input, select "MULTI CHANNEL."
See page 61 for details.
Basic operations
DIGITAL AUDIO OUTPUT
STREAM/PCM
ANALOG OUT DOLBY PROLOGIC
2-CH DOLBY SURROUND
D. RANGE COMPRESSION
ON
2-CH STEREO
MULTI CHANNEL
USE 5∞23 TO SELECT, USE ENTER TO CONFIRM
TO EXET, PRESS CHOICE.
ANALOG OUT selection
English
15