IBM Deskstar Deskstar 3 Quick Installation Manual
At/ide
Hide thumbs
Also See for Deskstar Deskstar 3:
- Installation and reference manual (72 pages) ,
- User manual (392 pages)
Advertisement
Quick Links
IBM storage products
Quick installation guide
Deskstar 3
AT/IDE
Models: DAQA-32160, DAQA-32700,
DAQA-33240
Handling precautions
1. Do not cover the breather hole! Covering the
breather hole may result in loss of data.
2. Do not press on the drive! Do not apply any force
to the drive during handling or installation.
3. Always handle the drive with care to prevent
damage from shock, vibration, or electrostatic
discharge (ESD).
4. Do not open the static-protective bag containing the
drive until required. Static electricity can damage the
drive.
5. Turn off and unplug your computer. Remove cover
6. When installing the drive, touch a grounded,
unpainted metal surface with the static-protective
package containing the drive for at least two seconds.
(This drains static electricity from the package and
from your body.)
7. Handle the drive carefully by the edges. Do not
touch any exposed printed circuit board.
Power
Connector
Back side of drive
Logic Card
AT I/F
Connector
JP7
Option Block
JP1
Power
Connector
8. Save the drive packaging material including the
ESD bag in the event that the drive must be returned.
Place the drive in an anti-static bag before placing it
in the shipping container. The warranty will be void if
the drive is not returned in IBM approved packaging.
Quick installation procedure
Note: It is advisable to backup all data before
proceeding with the installation.
If your system BIOS cannot handle large capacity
drives (over 540 MB), you may need to use a disk
overlay program such as Ontrack’s Disk Manager.
The following procedure uses the Ontrack Disk
Manager software. Information on obtaining a copy of
Ontrack’s Disk Manager can be found on the Web at
www.ibm.com/harddrive.
Setting the jumpers
1. In a one-drive system, configure your new drive as
Master (Device 0).
2. In a two-drive system, one drive must be desig-
nated as the Master, the other as the Slave (Device 1)
3. When installing the new drive as a Slave, check the
Master drive to determine if a jumper change is
required to indicate that a Slave drive is present.
4. Consult your manual to see if your computer
supports Cable Select before choosing this option.
Master active
JP1
Slave active
JP2
JP1
JP2
JP3
JP4
JP5
JP6
JP7
Cable select
JP3
Slave present/
11
13
1
3
5
7
9
Master active JP4 (DCAA)
Reserved
JP4 (DAQA)
12
10
14
2
4
6
8
Write cached
disabled
JP5
Reserved
JP6
Reserved
JP7
Page 1
Advertisement
Related Manuals for IBM Deskstar Deskstar 3
Summary of Contents for IBM Deskstar Deskstar 3
-
Page 1: Quick Installation Guide
Quick installation guide Deskstar 3 AT/IDE Models: DAQA-32160, DAQA-32700, DAQA-33240 Handling precautions 1. Do not cover the breather hole! Covering the breather hole may result in loss of data. 2. Do not press on the drive! Do not apply any force to the drive during handling or installation. - Page 2 Telephone: 888.IBM.5214 or 507.286.5825 Fax: 507.253.DRIVE E-mail: drive@us.ibm.com Singapore Technical Support Center Telephone: (65)6418.9595 or 1800.418.9595 E-mail: drive@sg.ibm.com IBM Systems Storage Division 5600 Cottle Road San Jose, CA 95193 www.ibm.com/storage Printed in the United States of America 01-99 All Rights Reserved IBM is the registered trademark of International Business Machines Corporation.