Hatco Atmospheric AWD-12 Specifications page 2

Water Inlet
1
( ⁄ " Male Flare
4
Connection)
Cord Location
SPECIFICATIONS
Model Volts Watts
208 5000
AWD-12
240 5000
WATER TEMPERATURE RECOVERY
Dispensing Temperature of 200ºF (93ºC)
12 gph (45 lph) with 35ºF (2ºC) incoming water
33 gph (125 lph) with 140ºF (60ºC) incoming water
gph = (kW x 400)/(ºF Temperature Rise)
lph = (kW x 841)/(ºC Temperature Rise)
OPTIONS
(NOT FOR RETROFIT)
K NEMA L6-30P Locking Cap in lieu of NEMA 6-30P
PRODUCT SPECS
Water Dispenser
The Atmospheric Water Dispenser to supply water ranging from
75º–200ºF (24º–93ºC) shall be a Hatco Model ....as
manufactured for commercial use by the Hatco Corporation,
Milwaukee, WI 53234 U.S.A.
The Water Dispenser shall have the capacity to heat 12 gph
(45 lph) from 35º to 200ºF (2º to 93ºC) and it shall be rated
at ....volts, ....watts.
The dispenser shall be complete with a stainless steel tank and
all internal plumbing, including a
the inlet and a 3 / " hose connection on the drain. All controls
4
shall be built-in, including contactor.
HATCO CORPORATION P.O. Box 340500 Milwaukee, WI 53234-0500 U.S.A. • (800) 558-0607 • (414) 671-6350
Fax (800) 543-7521 • Int'l. Fax (414) 671-3976 • www.hatcocorp.com • E-mail: equipsales@hatcocorp.com
Form No. AWD-1006(S)
ATMOSPHERIC
Model AWD-12
1
27 ⁄ " (699 mm)
2
1
23 ⁄ " (597 mm)
2
4"
(102 mm)
8"
(203 mm)
Manual
Drain Lever
Outlet for Manual Drain
3
(Standard ⁄ " Hose Connection)
4
SIDE VIEW
Amps Shipping Weight
24.0 80 lbs. (36 kg)
20.8 80 lbs. (36 kg)
1 / " male flare connection on
4
ITEM#
HOT WATER DISPENSER
7
11 ⁄ "
8
1
1 ⁄ " (302 mm)
2
(38 mm)
3
11 ⁄ "
4
(298 mm)
1
8 ⁄ "
8
(206 mm)
Cord Location
FRONT VIEW
DIMENSIONS
13 3 / "W x 27 1 / "D x 28 1 / "H (340 x 699 x 714 mm)
8 2 8
with 4" (102 mm) legs.
VOLTAGE
208 or 240 volts, 50/60 Hz, single phase (use NEMA 6-30P).
CORD LOCATION
Lower left side.
PLUG CONFIGURATIONS
NEMA 6-30P NEMA L6-30P
ACCESSORIES
K 3' (914 mm) Rubber Drain Hose with 10' (3048 mm)
1
/ " Inlet Tubing
4
K Phosphate Injection System
K Plumbing Kit for Phosphate Injection
The heater shall be equipped with an electronic temperature
controller, an on-off switch, a digital temperature display, and
preset dispensing push-buttons including manual dispense.
Electric heating elements shall be metal sheathed, controlled by
a submersed thermistor. The Water Dispenser shall be protected
with high-temperature limit and low-water cut-off. The unit may
be emptied easily by a convenient bottom drain.
The dispenser shall consist of a stainless steel tank, front cover,
front control housing, and a painted white granite body with
standard 4" (102 mm) legs and 6' (1829 mm) cord and plug.
24 1 ⁄ "
8
(613 mm)
1
28 ⁄ "
8
(714 mm)
4"
(102 mm)
Printed in U.S.A.