Advertisement
Table of Contents
Sunshield™ 12ft X 20ft
12ft3in Wide x 20ft Deep x 6ft8in Side Height
With 8 Legs, Fitted Cover with Leg Skirts, Side-Wall kit (2 Side Panels,
1 Rear Panel). Elastic Ball Straps, Foot Pads and Valance Tie Downs.
Distributed by:
PIC America, LTD.
1730 Five Points Lane • Fuquay-Varina, NC 27526
1-800-800-6296 • www.kingcanopy.com
9ft9in Center Height
King Canopy Item #: C81220PC3W
WARNING:
Keep all flame and heat sources
away from this tent fabric. Meets
the flammability requirements of
CPAI-84 Section 6 and NFPA-701.
It is not fire proof. The fabric will burn if
left in continuous contact with
any flame source.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for KING CANOPY Sunshield C81220PC3W
Summary of Contents for KING CANOPY Sunshield C81220PC3W
- Page 1 12ft3in Wide x 20ft Deep x 6ft8in Side Height 9ft9in Center Height King Canopy Item #: C81220PC3W With 8 Legs, Fitted Cover with Leg Skirts, Side-Wall kit (2 Side Panels, 1 Rear Panel). Elastic Ball Straps, Foot Pads and Valance Tie Downs.
-
Page 2: Parts List
PARTS LIST 6X6PC 25 pc 1 3/8” diameter 6’6” Pipe 3WPC 6 pc 3-way connectors 4WPC 6 pc 4-way connectors BALLW 75 pc Elastic ball straps T81020SWW 2 pc Sidewalls T81220EW 1 pc End wall PFOOT 8 pc Foot pads PTCL1220TV 1 pc Fitted Cover with Leg Skirts... -
Page 3: Frame Assembly
FRAME ASSEMBLY Step 1 Place all corners and pipe on the ground as shown. All pipes are 78’’ long. 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ 78’’ Step 2 Start with the center and complete the center frame first. Then assemble each side. NOTE: Attach the cover before inserting the legs. -
Page 4: Cover Assembly
COVER ASSEMBLY Step 1 Unfold the cover with the grommets toward the cover’s bottom and place over the frame. The flared edges should be located at each of the 4 corners of the frame. Step 2 Begin attaching the cover with the elastic ball straps by inserting the elastic cord of the ball strap underneath the cover and through the grommet. - Page 5 WALLS AND LEGS ASSEMBLY Step 1 Unfold each of the walls. • The back wall • The 2 side walls Step 2 Find the hook & loop fastening strips on one length of the first sidewall to be assembled. These strips are to be placed on the top pipe of your canopy structure by wrapping the fastening strips over the perimeter poles.
- Page 6 ANCHORING YOUR UNIT This canopy is designed for use as a temporary structure. After assembly, the canopy MUST BE securely anchored to the ground to prevent damage from winds. Your canopy will act like a kite in the wind if not properly and securely anchored to the ground.
- Page 7 INSTALLING THE LEG SKIRTS Step 1 After the legs have been connected to the roof using the 3- and 4-way connectors and your canopy has been securely anchored, attach the leg skirts using elastic ball straps and the grommets at the top of the unit. (Make sure that the end walls are underneath the flared leg covers to minimize rain and other elements from entering inside the canopy unit.) Step 2...
- Page 8 IMPORTANT NOTICE: PLEASE READ CAREFULLY We are confident that you will be completely satisfied with your King Canopy unit. Please take a moment to read the very important information below, and call us with any questions you may have. King Canopy/PIC America, LTD. has no control over wind, snow, ice, rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy.
-
Page 9: Product Information
Improper Anchoring, Strong Winds, Rain Snow, or Ice King Canopy/PIC America, LTD. does not guarantee these canopies under strong weather conditions. These canopies are designed to protect against damages caused by sun, rain, tree sap, birds, etc. They are not designed to hold roof loads that accompany snow, ice or heavy rains.
Need help?
Do you have a question about the Sunshield C81220PC3W and is the answer not in the manual?
Questions and answers