Harman Kardon AVR 70 Owner's Manual page 29
Harman kardon avr 70: owners manual
Hide thumbs
Also See for AVR 70:
- Technical manual (139 pages) ,
- Owner's manual (32 pages) ,
- Quick start manual (113 pages)
Table of Contents
Advertisement
AVR70 engelsk manual
11/01/98 11:57
On Screen Menus
In addition to the information shown on
the front panel display, it is also possible
to obtain the unit’s current status
through the use of on screen video
messages. The on screen menus may also
be used to control many aspects of the
receiver and to make adjustments and
selections.
To activate the On Screen display system,
press the
SCREEN DISPLAY s
button on the remote. This will cause a
status summary display to be shown on
the screen for five seconds. (Figure #4).
Once the video displays are enabled, this
status screen will also appear when the
unit is turned on.
NOTE: In order to view the on screen
menu displays the receivers video jack
TV
must be connected to the
MONI P
standard, composite video input of a TV
monitor or projector. The on screen
displays are NOT visible via the “S” video
output
.
Q
The status screen displays the following
information:
: This is the input
AUDIO SOURCE
currently selected for audio.
: This is the input
VIDEO SOURCE
currently selected for video.
: This is the currently selected
MODE
audio/surround mode.
: This is the
MASTER VOLUME
current volume level. Note that
volume appears as a horizontal scale.
The “0dB” reference level is indicated
by a solid block
if volume catches
Í
or exceeds it, while volume levels
below the current level are indicated
±
by double vertical bars
.
Side 23
On Screen Display
23
Function Displays and Messages
Once the On Screen Displays have been
activated, they appear when certain
functions are performed from the front
panel buttons or the remote control.
These messages are three line displays
with the current function shown on the
top line and information about the
selection or choice on the bottom two
lines.
The following function/operation display
screens are available:
Surround Mode and Delay
When the surround mode is changed or
the delay timing is adjusted, this message
will appear at the bottom of the video
screen. The top line is the surround
mode, the bottom line is the delay time
for that mode. (Figure #5) Note that
delay time will not be displayed in the
or
STEREO
DOLBY 3 STEREO
modes, as these modes do not have rear
channel information.
Input Selection
When the source input is changed, this
message will appear (Figure #6). The top
line is the audio input source, the bottom
line is the video input source. Remember,
when choosing an input, select the video
source first, and then the audio source if
a split input/simulcast listening session is
desired.
Surround Output Levels
To obtain a status screen with the outputs
for each individual channel, press the
button
on the remote. A
v
SPEAKER
summary will appear for ten seconds.
(Figure #7)
A U D I O
S O U R C E
:
T U N E R
V I D E O
S O U R C E
:
V C R 2
M O D E
:
D O L B Y
P R O
L O G I C
M A S T E R
V O L U M E
||
Figure 4
M O D E
: D O L B Y
P R O L O G I C
D E L A Y
T I M E : 2 0 m s e c
Figure 5
< F U N C T I O N
S E L E C T >
A U D I O : T U N E R
V I D E O : V C R 1
Figure 6
F R O N T
L
:
+ 1
d B
F R O N T
R
:
2
d B
C E N T E R
:
+ 5
d B
S U R R O U N D
:
1 0
d B
Figure 7
Hide quick links:
Advertisement
Table of Contents
