System And Power Connections - Harman Kardon AVR 525 Owner's Manual

device should be made to either the Video 2 Audio
39
Inputs or any of the Optical or Coaxial Digital
Input Jacks
33 36 .
8. If the component video inputs are used, connect
the Component Video Monitor Outputs b to the
component video inputs of your TV, projector or dis-
play device.
9. If you have a camcorder, video game or other
audio/video device that is connected to the AVR on a
temporary, rather than permanent, basis, connect the
audio, video and digital audio outputs of that device to
the Front-Panel Inputs . A device con-
nected here is selected as the Video 4 input, and the
digital inputs must be assigned to the Video 4 input.
(See page 19 for more information on input configu-
ration.)
Video Connection Notes:
• When the component video jacks are used, the on-
screen menus are not visible and you must switch
to the standard composite or S-Video input on your
TV to view them.
• The AVR 525 will accept either standard composite,
S-Video or Y/Pr/Pb component video signals.
However, it will not convert composite or S signals
to component video.
• Component or composite video signals may only be
viewed in their native formats.

System and Power Connections

The AVR 525 is designed for flexible use with multi-
room systems, external control components and
power amplifiers.
Main Room Remote Control Extension
If the receiver is placed behind a solid or smoked
glass cabinet door, the obstruction may prevent the
remote sensor from receiving commands. In this
event, an optional remote sensor may be used.
Connect the output of the remote sensor to the
Remote IR Input g jack.
If other components are also prevented from receiving
remote commands, only one sensor is needed. Simply
use this unit's sensor or a remote eye by running a
connection from the Remote IR Output h jack to
the Remote IR Input jack on Harman Kardon or other
compatible equipment.
Multiroom IR Link
The remote room IR receiver should be connected to
the AVR 525 via standard coaxial cable. Plug the IR con-
nection cable into the Multiroom IR Input f jack on
the AVR 525's rear panel.
If other Harman Kardon compatible source equipment
is part of the main room installation, the Remote IR
Output h jack on the rear panel should be connected
to the IR IN jack on source equipment. This will enable
the remote room location to control source equipment
functions.
NOTE: All remotely controlled components must be
linked together in a "daisy chain. " Connect the IR OUT
jack of one unit to the IR IN of the next to establish
this chain.
Multiroom Connections
The AVR 525 is equipped with multizone capabilities
that allow it to send a separate audio source to the
remote zone from the one selected for use in the
main room.
Depending on your system's requirement, three
options are available for audio connection:
Option 1: Use high-quality, shielded audio intercon-
nect cable from the AVR 525's location to the remote
room. In the remote room, connect the interconnect
cable to a stereo power amplifier. The amplifier will be
connected to the room's speakers. At the AVR 525,
plug the audio interconnect cables into the Multiroom
Audio Output j jacks on the AVR 525's rear panel.
Option 2: Connect the Multiroom Audio Output j
jacks on the AVR 525 to the inputs of an optional
stereo power amplifier. Run high-quality speaker wire
from the amplifier to the speakers in the remote room.
Option 3: Taking advantage of the AVR 525's built-in
seven-channel amplifier, it is possible to use two of the
amplifier channels to power speakers in the remote
room. When using this option you will not be able to
use the full 7.1-channel capabilities of the AVR 525 in
the main listening room, but you will be able to add
another listening room without additional external
power amplifiers. To use the internal amplifiers to
power a remote zone, connect the speakers for
the remote room location to the Surround Back/
Multiroom Speaker Outputs ‚. Before using the
remote room you will need to configure the amplifiers
for surround operation by changing a setting in the
Advanced Select menu, following the instructions
shown on page 34.
NOTE: For all options, you may connect an optional IR
sensor in the remote room to the AVR 525 via an
appropriate cable. Connect the sensor's cable to the
Multiroom IR Input f on the AVR 525 and use the
Zone II remote to control the room volume. Alter-
natively, you may install an optional volume control
between the output of the amplifiers and the speakers.
A-BUS Installation Connections
The AVR 525 is among the very few receivers avail-
able today that offers built-in A-BUS Ready
tion. When used with an optional A-BUS keypad or
control module, you have all the benefits of remote
zone operation without the need for an external power
amplifier.
To use the AVR 525 with an approved A-BUS prod-
uct, simply connect the keypad or module that is in
the remote room to the AVR 525 using standard
"Category 5" wiring that is properly rated for the in-
wall use specific to the installation. Terminate the
wiring at the receiver end to a standard RJ-45 jack
in compliance with the instructions furnished with the
A-BUS module.
No further installation or adjustment is needed, as the
A-BUS connector on the AVR 525 routes the signals
in and out of the keypad to their proper destination for
power, signal source and control. The output fed to the
A-BUS jack is determined by the AVR 525's multi-
room system, and the menus may be used as is.
RS-232 Connections
The AVR 525 includes an RS-232 serial port connec-
tion that may be used to control the unit via compati-
ble optional, external keypads or control systems. The
physical connection to the AVR 525 from the control
device is a standard D-9 connection, but to assure
compatible and proper operation, specific software
commands and pin wiring schemes are required.
Due to the complexity of RS-232 connections
we recommend that they be made only by trained
installers familiar with their use. To obtain additional
information on the use of the AVR 525 with RS-232
control, please contact Harman Kardon's customer
service department or consult our Web site at
www.harmankardon.com.
AC Power Connections
This unit is equipped with three accessory AC outlets.
They may be used to power accessory devices, but
they should not be used with high-current draw equip-
ment such as power amplifiers. The total power draw
to each outlet may not exceed 100 watts.
The Switched AC Accessory Outlet ⁄ will receive
power only when the unit is on. This is recommended
for devices that have no power switch or a mechanical
power switch that may be left in the "ON" position.
NOTE: Many audio and video products go into a
Standby mode when they are used with switched out-
lets, and cannot be fully turned on using the outlet
alone without a remote control command.
The Unswitched AC Accessory Outlet ¤ will
receive power as long as the unit is plugged into a
powered AC outlet.
® opera-