1. Manuals
  2. Brands
  3. Tormach Manuals
  4. Enclosure
  5. 770M
  6. Installation manual

Tormach 770M Installation Manual

Enclosure kit
Hide thumbs Also See for 770M:
Table of Contents

Advertisement

Quick Links

Download this manual
TECHNICAL DOCUMENT
Version 0522A
INSTALLATION GUIDE
770M ENCLOSURE KIT
Page 1
Specifications subject to change without notice.
©Tormach® 2022

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 770M and is the answer not in the manual?

Questions and answers

Related Manuals for Tormach 770M

Summary of Contents for Tormach 770M

  • Page 1 TECHNICAL DOCUMENT Version 0522A INSTALLATION GUIDE 770M ENCLOSURE KIT Page 1 Specifications subject to change without notice. ©Tormach® 2022...

  • Page 2: Product Information

    Verify the received goods against the packing list. If there is any damage or shortages, you must contact Tormach within 30 days of receipt. Create a support ticket with Tormach Technical Support at tormach.atlassian.net/servicedesk for guidance on how to proceed.

  • Page 3: Installation

    3. Attach the left rear panel to the left chip pan with three M6 × 1.0 - 12 screws. Figure 2-1: Left rear panel attached to the left chip pan. Page 3 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 4 2. Attach the left side panel to the left chip pan with five M6 × 1.0 - 12 screws. Figure 2-3: Left side panel attached to the left chip pan. Page 4 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 5 3. Loosely attach one horizontal window retainer to the bottom of the left side panel's window opening with two M5 × 0.8 - 10 screws. Figure 2-4: Side window retainers attached to the left side panel. Page 5 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 6 2. Attach the left front panel to the left side panel with seven M5 × 0.8 - 10 screws. Figure 2-6: Left front panel attached to the left side panel. Page 6 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 7 3. Loosely attach one horizontal window retainer to the bottom of the right side panel's window opening with two M5 × 0.8 - 10 screws. Figure 2-7: Side window retainers attached to the right side panel. Page 7 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 8 1. Attach the left top panel to the panels on the left side of the enclosure with 12 M5 × 0.8 - 10 screws. Figure 2-10: Left top panel attached to the left side of the enclosure. Page 8 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 9 2. Connect the left and right top panels with one M5 × 0.8 - 10 screw. Figure 2-13: Left and right top panels connected. Page 9 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 10 3. Attach three cable tie anchors to the right top panel with three M5 × 0.8 - 10 screws. Figure 2-14: Location to attach three cable tie anchors. Page 10 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 11 2. Attach the front upper panel to the right and left top panels with four M5 × 0.8 - 10 screws. Figure 2-16: Front upper panel attached to the right and left top panels. Page 11 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 12 Install the Rear Splash Shield Attach the rear splash shield to the right chip pan below the electrical cabinet with four M6 × 1.0 - 12 screws. Page 12 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 13 The linear rail mount's clamping screws must face up. Figure 2-20: Right lower linear assembly attached to the inside of the enclosure's lower right side. Page 13 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 14 3. Repeat Steps 1 to 2 for the remaining three linear rails, with the linear rail mount's clamping screws face in the following directions: Up on the lower linear assemblies Down on the upper linear assemblies Figure 2-22: Four linear assemblies attached to the enclosure. Page 14 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 15 NOTICE! To prevent window damage from over-tightening, use your fingers to tighten the screws. Figure 2-24: Window retainers attached to the front door. 6. Repeat Steps 1 through 5 to assemble the remaining front door. Page 15 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 16 4. To the edge of the front door that's closest to the left side of the enclosure, attach one door seal with three M5 × 0.8 - 10 screws. Figure 2-27: Door seal attached to the edge of the front door. 5. Repeat Step 4 for the remaining front door. Page 16 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 17 Read the OHMS value that displays. The value should be less than 5 OHMS. If the value is greater than 5 OHMS, don't install the floodlight. Create a support ticket with Tormach Technical Support at tormach.atlassian.net/servicedesk for guidance on how to proceed.
  • Page 18 Verify that the trim covers the entire perimeter of the window. When finished, use shears or a knife to cut the excess trim. Figure 2-31: Rubber trim pushed onto the window opening. 2. Remove and discard the protective plastic film from the windows. Page 18 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)

  • Page 19: Install The Access Panel

    2. Push a strip of rubber trim to the edge of the access panel opening on the left rear panel. Verify that the trim covers the entire perimeter of the opening. When finished, use shears or a knife to cut the excess trim. Page 19 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 20 Find the stainless steel wear guard that you set aside earlier. Attach it to the lower front panel with two M5 × 0.8 - 10 screws. Page 20 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 21 2.1 INSTALLATION Figure 2-38: Stainless steel wear guard attached to the lower front panel. Page 21 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)
  • Page 22 The machine has one maintenance label on each window. Figure 2-39: Window maintenance label. Write down today's date on each label with a permanent marker. You have completed assembling and installing the 770M Enclosure. Replace the Windows When required, replace the windows with the following parts:...

  • Page 23: Exploded Views And Parts Lists

    3.1 EXPLODED VIEWS AND PARTS LISTS Read the following sections for reference: 3.1.1 Enclosure Exploded View 3.1.2 Enclosure Parts List 3.1.1 Enclosure Exploded View Page 23 ©Tormach® 2022 tormach.com Specifications subject to change without notice. TD10536: Installation Guide: 770M Enclosure (0522A)

  • Page 24: Enclosure Parts List

    3.1.2 Enclosure Parts List Description Quantity Enclosure Panel, 770, Lower Front (PN 37600) Enclosure Panel, 770M, Left Front (PN 37603) Enclosure Panel, 770M, Right Front (PN 37601) Enclosure Panel, 770, Upper Front (PN 37605) Enclosure Panel, 770M, Left Side (PN 37604)
  • Page 25 Screw, Socket Head Cap, M5 × 0.8 - 20 (PN 30357) Screw, Socket Head Cap, M8 × 1.25 - 22 (PN 37190) Washer, Flat, M8 (PN 30531) Decal, Enclosure, 770M, Front Left Panel (PN 38745) Page 25 ©Tormach® 2022 tormach.com Specifications subject to change without notice.

This manual is also suitable for:

37548

Table of Contents