HP xw8400 Installation Instructions Manual
Front fan kit installation
Hide thumbs
Also See for xw8400:
- User manual (216 pages) ,
- Service and technical reference manual (210 pages) ,
- Technical reference manual (200 pages)
Advertisement
Quick Links
This document describes how to install a front fan in an HP workstation. The front fan provides extra
cooling for full-length PCI cards.
Kit contents
The kit for your workstation includes the following components:
■ Front fan
■ Installation instructions
■ Warranty
Before you begin
See www.hp.com/accessories/workstations to determine the compatibility of this product with your HP
workstation.
✎
This optional front chassis fan is recommended only if it is required for non-factory-integrated high power
PCI cards. When this fan is installed, HP recommends that you verify that the temperatures of the PCI card
and other components are within the limits recommended by the component suppliers.
Observe warnings and cautions
Å
WARNING: Any surface or area of the equipment marked with these symbols indicates the presence of
a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the
risk of injury from a hot component, allow the surface to cool before touching.
Å
WARNING: Any surface or area of the equipment marked with these symbols indicates the presence of
an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed
area.
Front fan kit installation
1/8
Front fan kit installation
Advertisement
Related Manuals for HP xw8400
Summary of Contents for HP xw8400
-
Page 1: Kit Contents
This optional front chassis fan is recommended only if it is required for non-factory-integrated high power PCI cards. When this fan is installed, HP recommends that you verify that the temperatures of the PCI card and other components are within the limits recommended by the component suppliers. -
Page 2: Step 1-Prepare The Workstation
✎ NOTE: HP accessories are for use in HP workstation products. They have been extensively tested for reliability and are manufactured to high quality standards. HP, therefore, warrants only those accessories that are manufactured or sold by HP. - Page 3 1. Remove the card guide from the chassis. Release the two card guide latches. Pivot the card guide toward the system board 1, and lift it out of the chassis 2. (The following figures show an HP xw8400 Workstation for reference.) 2.
- Page 4 3. Lower the front fan/card guide assembly into the chassis 1, rotate it back 2, and snap it into place. Be sure that the airflow direction arrow on the side of the fan faces the rear of the chassis. Connect the front fan wire connector to the front fan connector on the system board 3.
- Page 5 フ ロ ン ト フ ァ ン キ ッ ト の取 り 付け 本書では、 フ ロ ン ト フ ァ ン を HP Workstation に取 り 付け る 方法を説明 し ます。 フルレ ン グ ス PCI カー ド 用の フ ロ ン ト フ ァ ン を取 り 付け る と 、 冷却機能が向上 し ます。...
- Page 6 ✎ 注記 ： HP ア ク セサ リ は、 HP Workstation 製品に使用 し ます。 ア ク セサ リ は、 広範囲にわた る 信頼性試験を 実施 し てい る と と も に、 高い品質基準に従っ て製造 さ れてい ます。 当社が保証 し てい る ア ク セサ リ は、 当...
- Page 7 ド ガー ド を シ ス テ ム ボー ド の方向に回転 し て ( 図 1 参照 )、 シ ャ ーシか ら 持ち上げて取 り 出 し ます ( 図 2 参照 )。 ( 次の図は、 参考 と し て HP xw8400 Workstation の例を示 し てい ま...
- Page 8 シ ョ ン を再組み立て し ます。 こ の作業には、 サ イ ド ア ク セ ス パネルの取 り 付けお よ び電源の再 投入が含ま れます。 416481-001 フ ロ ン ト フ ァ ン キ ッ ト の取 り 付け © 2006 Hewlett-Packard Development Company, L.P. The HP Invent logo is a registered trademark of Hewlett-Packard Development Company, L.P.