Technical Data; Service / Warranty - Flymo 18V UltraTrim 260 Operator's Manual

To release retracted or welded trimmer line:
If the trimmer line (13) has disappeared into the spool
trimmer line extension still doesn't work after pulling the trimmer line
may be welded in the spool (22)
(22) (see 4. MAINTENANCE To replace the trimmer
1. Remove the spool
line).
(13)
2. Unwind the trimmer line
3. Clean the spool (22) , the automatic lever
(23)
The automatic lever must move freely.
4. Wind the trimmer line (13) onto the spool
(see 4. MAINTENANCE To replace the trimmer line).
5. Insert the spool (22) again (see 4. MAINTENANCE
To replace the spool).
Problem Possible Cause
Trimmer does not cut Trimmer line is worn or too
short.
Trimmer line is empty.
Trimmer line is pulled into the
spool or welded.
Trimmer line cannot be Trimmer line became too
extended or is used quickly dry and brittle (e. g. during
the winter).
Trimmer line frequently
touched hard objects.
Automatic lever is dirty.
Continuous clattering noise Too much trimmer line was
fed out.
Trimmer line limiter is missing. v Contact the FLYMO Service.
Wheel stops turning Wheel is dirty.
Trimmer can no longer Start lever is stuck.
be stopped
Trimmer does not start Battery is empty.
or stops.
(L1)
LED is flashing green
[ Fig. O4 ]
Trimmer does not start Battery temperature is outside
or stops. the permissible temperature
(Wp)
Error-LED is illuminated range.
red [ Fig. O4 ]
There are drops of water or
moisture between the battery
contacts on the trimmer.
Engine is blocked.
Trimmer does not start Product is defective.
or stops.
Error-LED (Wp) is flashing
red [ Fig. O4 ]
Trimmer does not start
Battery is not put completely
or stops. into the battery holder.
(Wp)
Error-LED is not
illuminated [ Fig. O4 ]
Battery is defective.
Product is defective.
Charging is not possible.
The battery is not connected
Battery charge indicator (Lc)
(correctly).
is continuously illuminated
Battery contacts are dirty.
[ Fig. O3 ]
Battery temperature is outside
the permissible charging
temperature range.
Battery is defective.
(Lc)
Battery charge indicator Mains plug of the charger is
is not illuminated [ Fig. O3 ] not (correctly) plugged in.
Battery charge indicator (Lc) Socket outlet, mains cable or
is not illuminated [ Fig. O3 ] charger is defective.
For any other malfunctions please contact the Husqvarna UK Ltd. Customer
Service. Repairs must only be done by Husqvarna UK Ltd. service departments
or specialist dealers approved by FLYMO.
8
42260-85.960.01.indd 8 42260-85.960.01.indd 8
(22) or if the automatic
.
.
(23) and the trimmer line
(22) again
Remedy
v Extend the trimmer line.
v Replace the spool or the
trimmer line.
v Pull the trimmer line out of
the spool.
v Put the spool in water for
approx. 10 hours.
v Prevent the trimmer line from
touching hard objects.
v Clean the automatic lever.
v Wind the trimmer line onto
the spool.
v Clean the wheel.
v Remove the battery and
loosen the start lever.
v Charge the battery.
v Wait until the battery tem­
perature is between
0 °C – + 45 °C again.
v Remove the water drops /
moisture with a dry cloth.
v Remove the obstacle.
Start again.
v Contact the FLYMO Service.
v Put the battery completely
into the battery holder until
it audibly engages.
v Replace the battery.
v Contact the FLYMO Service.
v Connect the battery to
charger correctly.
v Clean the battery contacts
(e. g. by connecting and
disconnecting the battery
several times. Replace the
battery if necessary.
v Wait until the battery
tem perature is between
0 °C – + 45 °C again.
v Replace the battery.
v Insert the mains plug into the
mains socket (completely).
v Check the mains voltage.
Let the charger be checked
if necessary by an authorised
specialist dealer or the
FLYMO Service.

7. TECHNICAL DATA

(13)
it
Battery Trimmer
Cutting width
Rpm of spool
Trimmer line diameter
(13) .
Trimmer line supply
Trimmer line feed
Weight (without Battery)
Sound pressure level L
1)
pA
Uncertainty k
pA
Sound power level L :
2)
WA
measured / guaranteed
Uncertainty k
WA
Hand / arm vibration a
1)
vhw
Uncertainty k
vhw
Measuring process complying with:
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of expo-
sure. The vibration emission value can vary during actual use of the electric power tool.
System Battery
Battery voltage
Battery capacity
Number of cells (Li-Ion)
Appropriate POWER FOR ALL system Battery Chargers:
AL 1810 CV / AL 1815 CV / AL 1830 CV / AL 1880 CV.
Battery Charger
AL 1810 CV P4A
Mains voltage
Mains frequency
Rated power
Battery charging voltage
Max. battery charging
current
Battery charging time 80 % /
97 – 100 % (approx.)
PBA 18V 2.0Ah W-B
PBA 18V 2.5Ah W-B
PBA 18V 4.0Ah W-C
Permitted charging
temperature range
Weight according to
EPTA-Procedure 01:2014
Protection class
Appropriate POWER FOR ALL system Batteries: PBA 18V.
8. ACCESSORIES
FLYMO Spool and line
FLYMO Trimmer line
FLYMO System Battery
PBA 18V/45 P4A
PBA 18V/72 P4A
FLYMO Battery Charger
AL 1810 CV P4A

9. SERVICE / WARRANTY

Service:
Please contact the address on the back page.
Unit Value
(Art. 9705445-xx / 9705447-xx)
cm 26
R/min. 8400
mm 1.6
m 8
automatic
kg 2.5
77
dB (A)
3
89 / 91
dB (A) 2
3
m/s
2
1.5
EN 50636­2­91 RL 2000/14/EC / S.I. 2001 No.1701
1) 2)
Unit Value (Art. 531382601)
PBA 18V 2.5Ah W-B
V (DC) 18
Ah 2.5
5
Unit Value (Art. 531382201)
V (AC) 220 – 240
Hz 50 – 60
W 26
V (DC) 18
mA 1000
min. 96 / 124
min. 120 / 154
min. 192 / 244
°C 0 – 45
kg 0.17
/ II
As replacement for consumed spool and line.
As replacement for consumed line.
Battery for additional duration or
for replacement.
Charger for the POWER FOR ALL system
Batteries PBA 18V..W­..
Art. FLY098 /
535670090
Art. NLO012 /
577616312
Art. 531382601
Art. 531382701
Art. 531382201
12.10.21 11:36 12.10.21 11:36