Larson Electronics EPS-DCSW-50A-600V Instruction Manual

Larson Electronics EPS-DCSW-50A-600V Instruction Manual

Advertisement

Thank you for your purchase of the Larson Electronics EPS-DCSW-50A-600V.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

INSTALLATION SHOULD ONLY BE CONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
RISK OF FIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IF NOT QUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
WARNING
TO AVOID THE RISK OF FIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTED AND MAINTAINED BY A QUALIFIED ELECTRICIAN ONLY, IN ACCORDANCE WITH ALL
APPLICABLE ELECTRICAL CODES.
TO AVOID ELECTRIC SHOCK:
BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
ALL FASTENERS SHOULD BE PROPERLY SEATED.
The Larson Electronics EPS-DCSW-50A-600V Hazardous Location Non-Fused Disconnect Switch/Breaker provides
operators with a Class II, Divisions 1 & 2, Groups E, F, G, Class III, Divisions 1 & 2 copper-free aluminum enclosure that
provides overcurrent and short circuit protection for service entrance, feeder or branch circuits, lighting, heating,
appliance and motor circuits. This 50 amp hazardous location disconnect switch and breaker features an EHD frame with
a 3-Pole 4-wire configuration. The EPS-DCSW-50A-600V operates on a maximum of 250V DC and features two cast 2"
conduit hubs; one on the top and one on the bottom.

WIRING

Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product
where weatherproofing may be required. Universal voltage driver permits operation at 250V DC 60Hz.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in the diagram 
Secure each pair of wires according to the diagram. Utilize a junction box or
similar
device
and
take
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
Larson Electronics, LLC
50 Amp Explosion Proof Disconnect Switch
Class 1 Division 1 - Groups C, D - 600V Rated
Instruction Manual
precautionary
steps
Phone: (800) 369-6671
, in all locations especially in outdoor areas
for
weatherproofing
all
Fax: (903) 498-3364
EPS-DCSW-50A-600V
www.larsonelectronics.com
1 of 2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EPS-DCSW-50A-600V and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Larson Electronics EPS-DCSW-50A-600V

  • Page 1 This 50 amp hazardous location disconnect switch and breaker features an EHD frame with a 3-Pole 4-wire configuration. The EPS-DCSW-50A-600V operates on a maximum of 250V DC and features two cast 2" conduit hubs; one on the top and one on the bottom.
  • Page 2 Inspect for good working condition prior to storage and before re-use. REPLACEMENT PARTS The EPS-DCSW-50A-600V is designed to provide years of reliable performance. Should the need for replacement parts arise, please contact Larson Electronics. THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

Table of Contents