Page 1
Tools required for assembly and service may not be included. For technical questions or replacement parts, please call 1‑800‑444‑3353. 4”x24” Model 97593 ® . All rights reserved. No portion of this manual or any artwork Manual Revised 10g...
SKU 97593 For technical questions, please call 1‑800‑444‑3353. NOTICE is used to address practices not related to personal injury. CAUTION, without...
Page 3
Use personal protective equip‑ ment. Always wear eye protection. Safety equipment such as dust mask, SKU 97593 For technical questions, please call 1‑800‑444‑3353. non-skid safety shoes, hard hat, or hearing protection used for appropri- ate conditions will reduce personal injuries.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into SKU 97593 For technical questions, please call 1‑800‑444‑3353. account the working conditions and the work to be performed. Use of the power tool for operations differ- ent from those intended could result in a hazardous situation.
(California Health & Safety Code § 25249.5, et seq.) 10. WARNING: Handling the cord on this product will expose you to lead, SKU 97593 For technical questions, please call 1‑800‑444‑3353. a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm.
To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. SKU 97593 For technical questions, please call 1‑800‑444‑3353. GROUNDING TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING...
Inc., the Canadian Standard Association, and the National Electri- cal Code. (See Outlets for 2‑Prong Plug.) SKU 97593 For technical questions, please call 1‑800‑444‑3353. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2‑Prong Plug.)
Page 8
150% of the rated amperes. Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions per Minute n 0 xxxx/min. (RPM) SKU 97593 For technical questions, please call 1‑800‑444‑3353. Page 8...
Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. SKU 97593 For technical questions, please call 1‑800‑444‑3353. OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION...
(39). Push the Belt Release Lever back in to se- cure the Belt in place, and make sure it’s on-center before starting a job. SKU 97593 For technical questions, please call 1‑800‑444‑3353. Belt Release Lever...
CARBON BRUSH MAINTENANCE. The carbon brushes may require maintenance when the motor perfor- SKU 97593 For technical questions, please call 1‑800‑444‑3353. mance of the tool decreases or stops working completely. To maintain the brushes: a.
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 97593 For technical questions, please call 1‑800‑444‑3353. Troubleshooting Likely Solutions 1.
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 97593 For technical questions, please call 1‑800‑444‑3353. PARTS LIST Qty.
Page 14
ASSEMBLY DIAGRAM (CONTINUED ON NEXT PAGE) SKU 97593 For technical questions, please call 1‑800‑444‑3353. Page 14...
Page 16
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 SKU 97593 For technical questions, please call 1‑800‑444‑3353. Page 16...