Related Manuals for Woods GSS54
Summary of Contents for Woods GSS54
- Page 1 GRADING SCRAPERS GSS54, GSS60, GSS72, GSM84, GSM96 GSS54B, GSS60B, GSS72B, GSM84B, GSM96B...
-
Page 2: Introduction
TO THE OWNER: Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ..............2 SPECIFICATIONS . -
Page 4: Specifications
SPECIFICATIONS GSS54 GSS60 GSS72 GSM84 GSM96 Product Weight (lbs) (With Scarifiers) Product Weight (lbs) (Without Scarifiers) Tractor H.P. 30 max 45 max 45 max 65 max 65 max Working Width (in.) 53.3 59.3 71.3 83.3 95.3 Overall Width (in.) 58.1 64.5... -
Page 5: Safety 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Power unit must be equipped with ROPS or Safety is a primary concern in the design and ROPS cab and seat belt. Keep seat belt securely manufacture of our products. Unfortunately, our fastened. -
Page 6: Maintenance
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Watch for hidden hazards on the terrain during equipment for eyes, hair, hands, hearing, and head; operation. and respirator or filter mask where appropriate. Stop power unit and equipment immediately ... -
Page 7: Safety & Instructional Decals
Replacement safety decals can be ordered free from your FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH. Woods dealer. To locate your nearest dealer, check the 55122-D Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637. - Page 8 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 3 – 55121 WARNING FALLING OFF CAN RESULT IN BEING RUN OVER. Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in “locked up” position at all times.
-
Page 9: Operation 9
The weight may be attained with front wheel weights, ballast in tires, front tractor weights The GSS54, GSS60 and GSS72 scrapers are compatible or front loader. Weigh the tractor and equipment. Do with Category 1, 3-point tractors equipped with side not estimate. -
Page 10: Adjusting Top Link
Quick Hitch Connection 2. Lock into position with lock pins provided. The lowest shank position will result in the greatest ground NOTICE penetration. The 3/4" bolt and sleeve in the lower hole provide ✰✱ ✶ 3. Lower scraper and drive tractor ahead to begin the attachment point for a Category 1 quick coupler. -
Page 11: Cleaning
CLEANING ❖ ❊ ❇ Inspect machine and replace worn or damaged parts. Sand down scratches and the edges of areas of ✫ ❐ ◆ After Each Use missing paint and coat with spray paint of matching Remove large debris such as clumps of dirt, grass, color (purchase from your dealer). -
Page 12: Owner Service
OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety information in this manual. ARNING ... -
Page 13: Replacing Scarifier Shank Tooth
REPLACING SCARIFIER SHANK TOOTH REPLACING CUTTING EDGE 1. Remove scarifier shank from the scarifier bar. All scraper models use two 1/2" x 6" (12.7 x 152 mm) cut- ting edges. They are interchangeable and reversible. 2. Refer to Figure 7. Remove the worn tooth by driving a chisel between the shank (1) and tooth (2). -
Page 14: Assembly
GRADING SCRAPER Assemble Grading Scraper Assembly of this Grading Scraper is the responsibility of the WOODS dealer. It should be delivered to the 1. Remove the banding, straps and lag bolts that owner completely assembled and adjusted for normal holds the scraper and mast plates to the pallet. -
Page 15: Dealer Check Lists 15
DEALER CHECK LISTS PRE-DELIVERY CHECK LIST front tractor wheels. When adding weight to attain 20% of tractor and equipment weight on (Dealer's Responsibility) front tractor wheels, you must not exceed the ROPS weight certification. Weigh the tractor Inspect the equipment thoroughly after assembly to be and equipment. -
Page 16: Parts
Pin, Bent 5/8 x 3 w/ Clip (GS54S) SU105 Cat 1 Drawbar Pin w/ Lynch Pin 1026530 Operator’s Manual Holder (not 1004635 Scarifier & Tip Assembly (GSS54) included) 1004636 Scarifier Tip 51243 5/16 NC x 1 GR5 Carriage Bolt 1002018 Sleeve .81 x 1.25 x 2.12... - Page 17 GSS60 & GSS72 GRADING SCRAPER (Model Without Scarifiers Not Shown) PART DESCRIPTION PART DESCRIPTION Grading Scraper Frame 6239 5/8 NC Hex Lock Nut (Not Serviced Separately) 1005338 Pin, Bent 5/8 x 3 w/Clip (GSS60) 1033040RP Side Skid 1005338 Pin, Bent 5/8 x 3 w/Clip (GSS72) 1029053 Mast Plate - Left 1026530...
- Page 18 GSM84 & GSM96 GRADING SCRAPER (Model Without Scarifiers Not Shown) PART DESCRIPTION PART DESCRIPTION Grading Scraper Frame 6239 5/8 NC Hex Lock Nut (Not Serviced Separately) 1005338 Pin, Bent 5/8 x 3 w/Clip (GSM84) 1033040RP Side Skid 1005338 Pin, Bent 5/8 x 3 w/Clip (GSM96) 1029053 Mast Plate - Left 1026530...
-
Page 19: Appendix 19
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. -
Page 20: Bolt Size Chart & Abbreviations
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG...............Agriculture MPa ............Mega Pascal ASABE ....American Society of Agricultural & N .............. -
Page 21: Repair Parts Warranty
Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice. -
Page 22: Product Warranty
The limited warranty covers any defects in the material and/or workmanship. Following the proper, recommended installation by an authorized Woods Dealer and normal use of a Woods mounting and backhoe or loader, if a tractor incurs damage resulting from the attachment, Woods will cover the existing tractor warranty in the event the manufacturer voids its tractor warranty because of the attachment.
Need help?
Do you have a question about the GSS54 and is the answer not in the manual?
Questions and answers