3=Zone Setup; Enable; Disable - Honeywell Fire-Lite Alarms ES-200X Manual

Programming
• The above increment function may be repeated with each press of the zero key.
As an example, the user could quickly enter 'FLR_3_ROOM 305' as follows:
1. The cursor is on the first letter of the Adjective field. Press the zero key twice to display F.LR_3
2. With the cursor on the first letter of the Noun field, press the zero key twice to recall the display ROOM_304. The cursor
automatically jumps from the first to the last letter of the Noun field.
3. With the cursor on the last letter of the Noun field, press the zero key again to increment the room number to 305.
4. Press the right arrow key to advance the zone field
5. Select a zone number from 000 to 099. Z000 (default zone) is the general alarm zone. Z001 through Z099 may be selected to link
software zones.
MNS Override
EDIT CONTROL
1=MNS OVERRIDE
2=CTRL MOD DLY
WIRELESS
Edit Control Screen #5
Control Module Delay
EDIT CONTROL
1=MNS OVERRIDE
2=CTRL MOD DLY
WIRELESS
Edit Control Screen #5
Wireless
EDIT CONTROL
1=MNS OVERRIDE
2=CTRL MOD DLY
WIRELESS
Edit Control Screen #5
3.6.3 Zone Setup
PROGRAMMING
1=AUTOPROGRAM
2=POINT PROGRAM

3=ZONE SETUP

Programming Screen #2

Enable

ZONE SETUP
1=ENABLE

2=DISABLE

3=SPECIAL PURPOSE
Zone Setup Screen #1
This screens allows the programmer to enable zones, one at a time. A flashing cursor appears next to the Z, prompting the programmer to
enter a three digit zone number (001 - 099). When the third digit is entered, the zone will be enabled and the cursor returns to the original
position next to the Z. Another zone can then be enabled.
Disable
ZONE SETUP
1=ENABLE
2=DISABLE
3=SPECIAL PURPOSE
Zone Setup Screen #1
This screen allows the programmer to disable zones, one at a time. A flashing cursor appears next to the Z, prompting the programmer to
enter a three digit zone number (001 - 099). When the third digit is entered, the zone will be disabled and the cursor will return to the
original position next to the Z. Another zone can then be disabled.
68
The MNS Override feature, when enabled, allows the ECC-50/100 to override the FACP and turn off an
NO
active control module or prevent the control module from activating during a mass notification event. Press-
NO
ing 1 while viewing Edit Control Screen #5 will cause the display to change from the factory default of MNS
NO
Override No to MNS Override Yes. Each press of the 1 key will cause the display to toggle between the two
options.
The control module delay feature, if enabled, will delay activation after being triggered by an alarm condi-
NO
tion. Pressing 2 while viewing Edit Control Screen #5 will cause the display to change from the factory
NO
default of Ctrl Mod Dly No to Ctrl Mod Dly Yes. Each press of the 2 key will cause the display to toggle
NO
between the two options. Delay time varies from 0-180 seconds. See "Control Module Delay" on page 75 to
set the delay time. The control module must first be set to Silenceable No to enable the Delay Timer.
The Wireless selection will update automatically if the system recognizes a wireless device. If the module
NO
is wireless, the display reads Wireless Yes. If the module is wired, the display will read Wireless No.
NO
NO
Pressing 3 while viewing Programming Screen #2 will access the Zone Setup screens as illustrated below:
ZONE SETUP
1=ENABLE
2=DISABLE
3=SPECIAL PURPOSE
Zone Setup Screen #1
Pressing 1 for Enable, while viewing Zone Setup Screen #1, will display the following screen:
Z
Pressing 2 for Disable, while viewing Zone Setup Screen #1, displays the following:
ZONE SETUP
1=ZONES INSTALLED
2=ZONES ENABLED
3=ZONES DISABLED
Zone Setup Screen #2
ZONE TO ENABLE
Enable Screen
ZONE TO DISABLE
Z
Disable Screen
ES-200X Series Manual — P/N LS10131-000FL-E:C 7/25/2018
Master Programming Level
ZONE SETUP
1=ZONE TYPES
2=ZONES AVAILABLE
3=ZONE MESSAGE
Zone Setup Screen #3