Page 1: Lcd Monitor
SyncMaster 400TSn/460TSn LCD Monitor User Manual...
Page 2: Safety Instructions
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Page 3 Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Do not connect multiple appliances to the same power outlet. • Do not disconnect the power cord while using the product. •...
Page 4 Do not install it in a badly ventilated location such as a bookcase or closet. • When putting the product down, make sure to put it down softly. • Do not place the front of the product on the floor. •...
Page 5 When cleaning the product, make sure to disconnect the power cord. • When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. • Since the product housing is easily scratched, make sure to use the specified cloth only.
Page 6 Safety Instructions Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.
Page 7 Safety Instructions Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces the weariness of your eyes. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
Page 8 Safety Instructions Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater. • This may reduce the lifetime of the product, and may result in fire. Do not drop any objects onto the product or cause any impact to the product.
Page 9: Package Contents
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking Manuals Quick Setup Guide...
Page 10 Others Remote Control Sold separately DVI Cable LAN Cable Note • You can purchase and connect a separate network box or TV tuner box. For information on how to use these, refer to their respective user manuals. • You can only connect one external box. Your LCD Display Front MENU button [MENU]...
Page 11 Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu val- ues. When OSD is not on the screen, push the button to adjust volume. ENTER button [ENTER] Activates a highlighted menu item.
Page 12 Introduction │ ] / OFF [O] POWER S/W ON [ Switches the LCD Display On/Off. POWER IN The power cord plugs into the LCD Display and the wall plug. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input)) DVI / PC / HDMI IN [HDMI]...
Page 13 Introduction DC OUT [5V/1.5A] Connect this to the POWER connector of a TV tuner box or network box. AV IN [VIDEO] (VIDEO Connection Termi- nal) Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.
Page 14: Remote Control
Note See Connecting Cables for further information regarding cable connections. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. Note The TV menu is available when a TV tuner box is installed.
Page 15 POWER 3. Number Buttons Introduction POWER Number Buttons button + VOL - MUTE TV/DTV MENU INFO COLOR BUTTONS TTX/MIX STILL AUTO S.MODE LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT MagicInfo P.MODE DUAL/MTS SWAP Turns the product On. Turns the product Off.
Page 16 4. DEL button 5. + VOL - MUTE 7. TV/DTV 8. MENU INFO 11.COLOR BUTTONS TTX/MIX 13.STILL 14.AUTO 15. S.MODE 16.MDC 17.LOCK SOURCE ENTER/PRE-CH 20. CH/P 21.D.MENU 22.GUIDE RETURN Introduction The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV.
Page 17 EXIT 27.MagicInfo 28. P.MODE DUAL/MTS 30. PIP 31.SWAP Mechanical Layout (400TSn) Mechanical Layout Introduction Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Exits from the menu screen. Selects SRS TruSurround XT mode. MagicInfo Quick Launch Button.
Page 18: Installation Vesa Bracket
Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Dimensions Introduction...
Page 19: Wall Bracket Installation
• Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Page 20 Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.
Page 21 Remove the 4 screws on the back of the product. Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. •...
Page 22 Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.
Page 23 • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
Page 24: Wall Bracket Assembly
• Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Page 25 Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.
Page 26 Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes. •...
Page 27 Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. Fix the product to the wall bracket. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.
Page 28: Connecting A Computer
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display.
Page 29: Connecting To Other Devices
Turn on both your computer and the LCD Display. • The DVI cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.
Page 30: Connecting To A Camcorder
Connecting to a Camcorder Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the LCD Display . Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display .
Page 31: Connecting Using A Dvi To Hdmi Cable
Connecting Using a DVI to HDMI Cable Note • Connect the DVI output terminal of a digital output device to the HDMI terminal of the LCD Display using a DVI to HDMI cable. • Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the DVI / PC / HDMI AUDIO IN terminal of the LCD Display.
Page 32: Connecting A Usb Device
Note Connect the LAN cable. Connecting a USB device Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance.
Page 33: Using The Software
Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic) Insert CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
Page 34: Installing The Monitor Driver (Manual)
Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) ® Microsoft Windows Vista™‚ Operating System Insert your Manual CD into your CD-ROM drive.
Page 35 Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. Click "Update Driver..." in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Page 36 Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence. ® ® Microsoft Windows XP Operating System Using the Software...
Page 37 Insert CD into the CD-ROM drive. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced...". Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver..."...
Page 38 "OK" button. Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Click the "Close" button then click "OK" button continually. Using the Software...
Page 39 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open"...
Page 40 Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location..." then click "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click "OK"...
Page 41 Installation MagicInfo Pro Installation Insert CD into the CD-ROM drive. Click the MagicInfo Pro installation file. When the Install Shield Wizard window appears, click "Next." Select "I agree to the terms of the license agreement" to accept the terms of use. You are required to log in to the MagicInfo Pro Server program.
Page 42 Choose a folder to install the MagicInfo Pro program. Click "Install." Using the Software...
Page 43 The "Installation Status" window appears. It is recommended restarting the system for the normal operation of the MagicInfo Pro Server program. Click "Finish". Using the Software...
Page 44: System Requirements
10. When the installation is complete, the MagicInfo Pro executable icon appears on your desktop. 11. Double-click the icon to start the program. System Requirements Minimum P1.8 Recommen- P3.0GHz IRTOUCH IRTouch Screen Control Panel Double click the mark on the tabletop (as the following indication), or follow "Start" -> "All programs" ->...
Page 45 Using the Software General Control Panel menu The control panel provides adjustment and configuration with USB and IR touchscreen of serial port and supports compatibility of multi-touchscreens at the same PC. This window shows the basic information of the touchscreen and calibration. If several touchscreens are mounted on the PC and status is set "multi-screens display", user may use the button [Select Monitor] and must choose monitor related to each touchscreen before calibration, otherwise the touchscreen won't work.
Page 46 Select the touchscreen you want in the list and Click [Calibrate]. After calibration, the item "Cali- brated" will show "Yes". Calibration compromising of steps: select a touchscreen in the information list, then click "calibrate" button when the calibration window shows up. Calibration is done by clicking on 4 calibration points so that user only clicks the center of the bull's-eye in sequence.
Page 47 Modes Setting Click on touch Mouse single click event happens immediately at the point when the finger contact the touchscreen, not for dragging objects. In this mode the touchscreen responds fastest, it's usually used for big button applications. Click on Release Mouse click event happens at the point where the finger leaves touchscreen;...
Page 48: Serial Port Settings
either fast or slow. Notice: the higher the value, the slower the pop-up time. "Delay" unit is "millisecond". The "area" is used for adjusting the jitter-range of the touch surface within limit of error (unit: pixel). The higher the value, the wider the jitter-range. Right Click menu will pop up so long as the finger contacts the screen for a while within the range.
Page 49 Click [Change Port] to set and change setting of the selected Serial Port. Attachment The general setting of touchscreen Select "Mouse Emulation" mode, then choose "Enable Touch" Send Right ClickEnable DoubleClick. In general functions of Enable Delay Touch and False touch rejection may not selected to avoidslowing the touch response.
Page 50 Installment Send Right Click : To enable right-click function (default). Click and press on any area on the screen for two second, the right-click menu will pop-up. Right-click is only available in Mouse Emulation mode. The “Delay” value is 1000(1second); The “Area” value is set to 32px at opti- mum.
Page 51 Specification Each value should be gradually set in "Delay Touch Settings" after fulfillment of "Enable Delay Touch". "Delay" is set to 40 and "Area" to 16. Enter count : It means how many times you click to approach the setting value within 3 seconds. Then driver will install the function of "False touch rejection"...
Page 52: Source List
Adjusting the LCD Display Input Available Modes • PC / DVI • • HDMI • MagicInfo Note The TV menu is available when a TV tuner box is installed. Source List MENU → ENTER → [Input] → ENTER → [Source List] →...
Page 53 → , → ENTER Name the input device connected to the input jacks to make your input source selection easier. HDMI Picture [PC / DVI / MagicInfo Mode] Available Modes • PC / DVI • • HDMI • MagicInfo Note The TV menu is available when a TV tuner box is installed.
Page 54 Entertain High brightness For watching motion pictures such as a DVD or VCR. Internet Medium brightness For working with a mixture of images such as texts and graphics. Text Normal brightness For documents or works involving heavy text. Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
Page 55: Color Tone
Sharpness MENU → → ENTER → [Picture] → [Sharpness] → , → ENTER Adjusts the Sharpness. Color Tone MENU → → ENTER → [Picture] → → →ENTER → [Color Tone] → , → ENTER The color tones can be changed. (Not available in Dynamic Contrast mode of On.) Cool Normal...
Page 56 MENU → → ENTER → [Picture] → [Red] → , → ENTER Green MENU → → ENTER → [Picture] → → → → ENTER → [Color Control] → → ENTER → [Green] → , → ENTER Blue MENU → → ENTER → [Picture] → ENTER →...
Page 57 Coarse MENU → → ENTER → [Picture] → → [Coarse] → , → ENTER Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine MENU →...
Page 58 (Not available in Dynamic Contrast mode of On.) Note The direct button on the remote control is the 'AUTO' button. Signal Balance This is used to make up for the weak RGB signal transmitted by a long signal cable. MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] (Available in PC mode only) (Not available in Dynamic Contrast mode of On.) Signal Balance...
Page 59 MENU → → ENTER → [Picture] → ance] → ENTER → → [Signal Control] → → → ENTER→ [B-Gain] → , → ENTER R-Offset MENU → → ENTER → [Picture] → ance] → ENTER → → [Signal Control] → → → → ENTER→ [R-Offset] →...
Page 60: Dynamic Contrast
Dynamic Contrast MENU → → ENTER → [Picture] → → → → → → → → → ENTER → [Dynamic Contrast] → , → ENTER Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast.
Page 61 (Not available in Dynamic Contrast mode of On.) Dynamic Standard Movie Custom Note The direct button on the remote control is the 'P.MODE' button. Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference. MENU →...
Page 62: Color Temp
→ , → ENTER Adjusts the picture Color. Tint MENU → → ENTER → [Picture] → → [Tint] → , → ENTER Adds a natural tone to the display. Color Tone MENU → → ENTER → [Picture] → → → ENTER → [Color Tone] →...
Page 63 → , → ENTER Color temp is a measure of the 'warmth' of the image colors. (Not available in Dynamic Contrast mode of On.) Note This function is only enabled if the Color Tone is set to Off. Size MENU → → ENTER → [Picture] → → → → → ENTER → [Size] →...
Page 64: Film Mode
→ , → ENTER Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. Film Mode MENU → → ENTER → [Picture] → → → → → → → ENTER → [Film Mode ] →...
Page 65 Sound Available Modes • PC / DVI • • HDMI • MagicInfo Note The TV menu is available when a TV tuner box is installed. Mode MENU → → → ENTER → [Sound] → ENTER → [Mode] → , → ENTER The LCD Display has a built-in high fidelity stereo amplifier.
Page 66 Note • You can hear the sound even when sound value is set to 0. • If you adjust sound using Custom function, Mode will turn to Custom mode. Bass MENU → → → ENTER → [Sound] → → ENTER → [Custom ]→ENTER→ [Bass] →...
Page 67 SRS TS XT MENU → → → ENTER → [Sound] → → → → ENTER → [SRS TS XT] → , → ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers.
Page 68: Clock Set
You can choose one of 11 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer. MENU →...
Page 69 On Timer MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → → ENTER→ [On Timer] → , / , → ENTER Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at the time the LCD Display turns on automatically.
Page 70: Energy Saving
Change the transparency of the background of the OSD. High Medium Opaque Safety Lock PIN MENU → → → → ENTER → [Setup] → → → → ENTER → [Safety Lock PIN ] → [0 9, 0 9, 0 9, 0 9] → [0 9, 0 9, 0 9, 0 9] → [0 9, 0 9, 0 9, 0 9] The password can be changed.
Page 71: Video Wall
→ , → ENTER When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected.
Page 72 Format MENU → → → → ENTER → [Setup] → → → → Wall ]→ → ENTER → [Format] → , → ENTER The Format can be selected to see a divided screen. Full Provides a full screen without any margins. Natural Displays a natural image with the original aspect ratio intact.
Page 73: Safety Screen
→ , → ENTER Sets how many parts the screen should be divided vertically. Five adjustment levels: 1, 2, 3, 4, and 5. Screen Divider MENU → → → → ENTER → [Setup] → → → → Wall ]→ → → → → ENTER → [Screen Divider] The screen can be divided into several images.
Page 74 Horizontal Dot MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → ENTER → [Pixel Shift] → → ENTER → [Horizontal Dot] → , → ENTER Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4.
Page 75 Timer Timer MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → ENTER → [Timer] → , → ENTER You can set the timer for Screen Burn Protection. If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish.
Page 76 Use this function to set the execution period for each mode set in the timer. Time MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → → → → ENTER → [Time] → , → ENTER Within the set period of time specify a time for execution.
Page 77: Resolution Select
Eraser MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → → → →ENTER → [Eraser] This function prevents after-images on the screen by moving a rectangular pattern. Resolution Select MENU →...
Page 78 → , → ENTER Adjusts the Power On time for the screen. Caution: Set the Power On time to be longer to avoid overvoltage. Side Gray MENU → → → → ENTER → [Setup] → → → → → → → → → → → ENTER →...
Page 79 Note Available in PC mode only Note The Reset function is not available when Video Wall is On. Color Reset MENU → → → → ENTER → [Setup] → → → → ENTER → [Reset ]→ → ENTER → [Color Reset ] →...
Page 80 → , → [0~9] • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. MagicInfo Available Modes •...
Page 81 • To setup MagicInfo on a Windows screen, refer to the MagicInfo Server Help. It is highly recommended not to turn off the AC power during an operation. • For pivoted LCD Displays, ticker transparency is not supported. • For pivoted LCD Displays, a screen resolution of up to 720*480(SD) is supported for movies. •...
Page 82 5. The Windows Desktop is displayed and the MagicInfo pro icon (the image will be inserted) appears. Move the cursor over the icon. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop.
Page 83: Slide Show
Auto Automatically fits the image to the window. Original Shows the properties of the original file. Slide Show Displays the properties of the original file as they are. Adjusting the LCD Display...
Page 84 Interval Controls the time intervals between image files for a slide show. (5 Sec, 10 Sec, 20 Sec, 30 Sec, 60 Sec) Rotation Displays an image file by turning it clockwise by 90 degrees. Adjusting the LCD Display...
Page 85 Zoom Displays a reduced picture. Close Closes the image control Menu. Adjusting the LCD Display...
Page 86 Music The MP3 file format is supported. Movie The MPEG1, WMV file format are supported. Play Plays a movie file. Adjusting the LCD Display...
Page 87 Full Size Plays a movie file in full screen. OFFICE / HTML PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF, HTML, HTM files are displayed. Note • Install the proper viewer(freeware) program to see the MS Office(Word, Excel, Power Point) or PDF doucuments.
Page 88: Schedule View
Internet Connects to the Internet Setup Sets various functions in MagicInfo mode. A password must be entered to access Setup mode. Schedule View Displays a schedule. Adjusting the LCD Display...
Page 89 TCP/IP Changes the TCP/IP settings. Connection Modifies the network settings. Adjusting the LCD Display...
Page 90 Password The password can be changed. • The password should be between 6 and 12 characters in numeric format. (You should enter a password between 6 and 12 characters in numeric format) • If you enter the wrong password three times, the setup configuration is reset and a warning message appears from the server.
Page 91: Play Option
Play Option You can set the repeat play and screen settings. Repeat : Determines the repeat option for playing movies and music. • None - Select No Repeat to play a movie or tune in the list only once. • File Repeat - Select Repeat File to play a movie or tune in the list repeatedly.
Page 92: Troubleshooting
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display.
Page 93: Check List
• Do not use benzene, thinner or other flammable substan- ces, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen sur- face.)
Page 94: Problems Related To The Screen
Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. The screen is blank and the power indicator is off. Ensure that the power cord is firmly connected and the LCD Display is on.
Page 95: Problems Related To Audio
Adjust color using Custom under OSD Color Adjustment menu. The color image is distorted by dark shadows. Adjust color using Custom under OSD Color Adjustment menu. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The Power Indicator blinks.
Page 96 Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Problems related to MagicInfo Note Making a Bootable USB Flash Disk. Making a Bootable USB Flash Disk 1) You can turn a common 512-MB or bigger USB storage media into a bootable disk using a USB bootable disk creation tool.
Page 97 Set the resolution at the Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Man- ual). How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the LCD Display with a soft cloth, using either a cleaning solution or plain water.
Page 98: Specifications
Dimensions (W x H x D) / Weight (With Stand) 971 x 645 x 311 mm / 38.2 x 25.4 x 12.2 inch / 28.6 kg / 63.1 lbs SyncMaster 400TSn 40 " Diagonal (101 cm) 885.17 mm (H) X 497.66 mm (V) 0.648 mm (H) X 0.648 mm (V)
Page 99 VESA Mounting Interface 600 mm x 400 mm Environmental considerations Operating Storage Audio Characteristics Audio Input 1 Audio Input 2 PC Audio Input Frequency Response Plug and Play Capability This LCD Display can be installed on any Plug & Play compatible system. The interaction of the LCD Display and the computer systems will provide the best operating conditions and LCD Display settings.
Page 100: Preset Timing Modes
Item File Internet Browser Language MagicInfo Pro - Server Requirement Minimum Recommended PowerSaver This LCD Display has a built-in power management system called PowerSaver. This system saves energy by switching your LCD Display to low-power mode when it has not been used for a certain amount of time.
Page 101 Display Mode VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 848 x 480 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 X 768 VESA, 1280 X 960...
Page 102 Display Color 16.7 M Resolution Optimum resolution 1920 x 1080 @ 60 Hz (RB) Maximum resolution 1920 x 1080 @ 60 Hz (RB) Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p ±5 % Separate H/V sync, Composite, SOG TTL level (V high ≥...
Page 103 Plug and Play Capability This LCD Display can be installed on any Plug & Play compatible system. The interaction of the LCD Display and the computer systems will provide the best operating conditions and LCD Display settings. In most cases, the LCD Display installation will proceed auto- matically, unless the user wishes to select alternate settings.
Page 104 PowerSaver This LCD Display has a built-in power management system called PowerSaver. This system saves energy by switching your LCD Display to low-power mode when it has not been used for a certain amount of time. The LCD Display automatically returns to normal operation when you press a key on the keyboard.
Page 105 Specifications Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the...
Page 106: For Better Display
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. •...
Page 107 Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. •...
Page 108 • Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically •...
Page 109 Note ( Please check CD's User Guide at "OSD Function", some model's will not available ) Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down. - Select method •...
Page 110 - Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not available ) Information...
Page 111: Contact Samsung Worldwide
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. U.S.A CANADA MEXICO ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA PANAMA PUERTO RICO REP.
Page 112 022 - 607 - 93 - 33 PORTUGAL 808 20 - SAMSUNG (7267864) http://www.samsung.com/pt SLOVAKIA 0800 - SAMSUNG (726-7864) http://www.samsung.com/sk SPAIN 902 - 1 - SAMSUNG (902 172 678) SWEDEN 075 - SAMSUNG (726 78 64) SWITZERLAND 0848 - SAMSUNG (7267864, CHF 0.08/min)
Page 113 Dot Pitch Vertical Frequency Horizontal Frequency Interlace Non-Interlace Methods Plug & Play Resolution Appendix Asia Pacific 1800-88-9999 http://www.samsung.com/my 0800 SAMSUNG (0800 726 http://www.samsung.com/nz 786) 1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph 1800-SAMSUNG(726-7864) http://www.samsung.com/sg 1800-29-3232, 02-689-3232 http://www.samsung.com/th 0800-329-999 http://www.samsung.com/tw 1 800 588 889 http://www.samsung.com/vn Middle East & Africa 0860-SAMSUNG(726-7864) http://www.samsung.com/za...
Page 114: Correct Disposal
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or con- sequential damages in connection with the furnishing, performance, or use of this material.
Page 115 Appendix...

This manual is also suitable for:

Syncmaster 460tsn

Samsung SyncMaster 400TSN User Manual

Quick Links

LCD Monitor

User Manual

Related Manuals for Samsung SyncMaster 400TSN

Summary of Contents for Samsung SyncMaster 400TSN

This manual is also suitable for:

Table of Contents