The Radio; Manual Tuning/Preset Tuning - Panasonic SC-HT900 Operating Instructions Manual

The radio

SELECTOR
TUNING
C.S.M PROGRESSIVE SELECTOR
V.R.S M.R.S
X W
TUNING TUNE MODE
AV SYSTEM
DIGITAL
TV/VIDEO AUX TUNER/BAND DVD/CD
DISC
1
DISC 1
PAGE
GROUP
4
DISC 4
SEQUENTIAL
7
REPEAT FL DISPLAY
PLAY MODE CANCEL
SKIP
: 9
X W
CH
CH
TOP MENU
DIRECT
NAVIGATOR
ENTER
ENTER
DISPLAY
TV VOL s
VOLUME
SUBWOOFER S.POSITION
LEVEL SFC
Manual tuning
1
Press [SELECTOR] to select "FM" or "AM".
Each time you press the button:
DVD/CD>FM>AM>TV>VCR>AUX>DIGITAL IN ([HT900])
^----------------------------------------------------------------------------}
≥Remote control: Press [TUNER/BAND].
2
Press [TUNE MODE] to select
"MANUAL".
Each time you press the button: MANUAL()PRESET
3
Press [X TUNING] or [TUNING W] to
select the frequency of the required
station.
≥Remote control: Press [6] or [5].
TUNED: Displayed when a radio station is
tuned.
ST: Displayed when a stereo FM broadcast is
being received.
Press and hold [XTUNING] or [TUNINGW] until the frequency
starts scrolling to start automatic tuning. Tuning stops when a
station is found.
4
Adjust the volume.
∫ If noise is excessive in FM
Press [FM MODE] to display "MONO".
Press [FM MODE] again to cancel the mode.
The mode is also canceled when you changed
the frequency.
∫ Allocation settings
Each country allocates broadcast bands according to their particular
system.
[For\U.S.A.,\Canada,\and\units\with\PX\printed\on\the\outer\packaging]
You can change the FM step. The step is factory-set to 0.2 MHz, but
you can change it to receive broadcasts allocated 0.1-MHz steps.
VOLUME, DOWN, UP
VOLUME
OPEN/CLOSE
DOWN UP
TUNE MODE FM MODE MEMORY
DISC EXCHANGE DISC SKIP
DISC 1 2 3 4 5
MEMORY
FM MODE
TV VCR
TUNER/BAND
2 3
DISC 2 DISC 3
5 6
Numbered
DISC 5
buttons
8 9
S10/ENTER
0
SLOW/SEARCH
6 5
MENU
PLAY LIST
RETURN
TV VOL r
VOLUME
j i
C.FOCUS MIX 2CH
S SRND
PL
TUNEDST
MONO
[For\Latin\America]
You can change the AM step. The step is factory-set to 9 kHz, but
you can change it to receive broadcasts allocated 10-kHz steps.
1 Press [TUNER/BAND] to select "FM" (for either band).
2 Press and hold [SELECTOR] on the main unit.
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM/AM frequencies preset in channels will be changed by this
procedure. Preset them again.
Preset tuning
Preset channels to make selection simple.
Up to 15 stations can each be set in the FM and AM bands.
Automatic presetting
1
Tune to "FM 87.9 MHz" or
"FM 87.5 MHz" (➡ left).
[For\Latin\America]
Tune to "FM 87.50 MHz" (➡ left).
2
Press and hold [ENTER].
≥Main unit: Press and hold [MEMORY].
Release the button when "FM AUTO" is displayed.
The tuner presets all the stations it can receive into the
channels in ascending order.
"SET OK" is displayed when the stations are set. The last
station to be set is then played.
3
Tune to "AM 520 kHz".
[For\Latin\America]
Tune to "AM 522 kHz" or "AM 520 kHz".
4
Press and hold [ENTER].
≥Main unit: Press and hold [MEMORY].
∫ "ERROR" is displayed
Presetting was unsuccessful. Preset manually.
Manual presetting
1
Tune to the station (➡ left).
2
Press [ENTER].
3
While "PGM" is flashing
Press the numbered buttons to select
a channel.
Alternatively, press [:, X CH] or [9, CH W] then press
[ENTER].
The station occupying a channel is erased if another station is preset
in that channel.
Selecting channels
1
Press [TUNER/BAND] to select "FM"
or "AM".
2
Press the numbered buttons or
[:, X CH] or [9, CH W] to select
the channel.
To select a 2-digit number
Example: To select channel 12, press [S10] ➡ [1] ➡ [2]
RQT6750
27