Advertisement
Quick Links
Advertisement
Related Manuals for HIKVISION DS-2CD2563G0-IS
Summary of Contents for HIKVISION DS-2CD2563G0-IS
- Page 1 Dome Network Camera Quick Start Guide...
- Page 2 QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR...
- Page 3 OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
- Page 4 more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help FCC conditions This device complies with part 15 of the FCC Rules.
- Page 5 Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
-
Page 6: Cautions And Warnings
Cautions&Warnings These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. Laws and Regulations The device should be used in compliance with local laws, electrical safety regulations, and fire prevention regulations. Transportation Keep the device in original or similar packaging while transporting it. -
Page 7: Maintenance
Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion. Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas. -
Page 8: Time Synchronization
Make sure the running environment meets the requirement of the device. The operating temperature shall be -30 °C to 60 °C (-22 °F to 140 °F), and the operating humidity shall be 95% or less (no condensing). DO NOT place the device in extremely hot, cold, dusty or damp locations, and do not expose it to high electromagnetic radiation. -
Page 9: Symbols And Marks
The standard power supply is 12 VDC or PoE, please make sure your power supply matches with your device. Make sure that the power has been disconnected before you wire, install, or disassemble the device. Make sure that no reflective surface is too close to the device lens. - Page 10 MicroSD card Grounding Disposal Purchase separately Other situations Other situations omitted Waterproof Skip this step if not necessary...
- Page 12 PM4x10 PA4x25...
- Page 13 microSD...
- Page 14 A.1-A.3 B.1-B.4...
- Page 15 5.5mm Ø 40mm Ø...
- Page 16 PA4x25...
- Page 18 5.5mm Ø PA4x25...
- Page 25 0° - 75° -30° - 30°...
- Page 26 0° - 360°...
- Page 29 RESET microSD Power Interface Alarm Interface Audio Interface Network Interface...
- Page 30 RESET microSD Power Interface Alarm Interface Audio Interface Aviation Plug...
- Page 31 Activate and Access Network Camera Scan the QR code to get Activate and Access Camera. Note that mobile data charges may apply if Wi-Fi is unavailable.
- Page 32 Reset and Restore Camera Press Reset button for about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. For the position of the reset button, refer to the figure in the page 19 or page 20.
- Page 33 UD18998B...
Need help?
Do you have a question about the DS-2CD2563G0-IS and is the answer not in the manual?
Questions and answers
Для подключения к программе Hik-Connect, нужен верификационный код , где взять ?
You can create or change the verification code for the camera during the setup process when selecting Hik-Connect as the Platform Access Mode. The code is needed to add the camera to the Hik-Connect app.
This answer is automatically generated