Advertisement
Main
Sub
Contents
code
code
09
01
Duplex motor forward rotation
check
02
Duplex motor reverse rotation
check
04
Duplex motor RPM adjustment
05
Duplex motor switchback time
adjustment
10
-
Toner motor operation
14
-
Trouble cancel (except for U2)
16
-
U2 trouble cancel
20
01
Maintenance counter clear
21
01
Maintenance cycle setting
02
Mini maintenance cycle setting
(Valid only when the destination is
set to Japan AB series.)
22
01
Maintenance counter display
02
Maintenance preset display (Valid
only when the destination is set to
EX Japan)
03
Jam memory display
04
Jam total counter display
05
Total counter display
06
Developing counter display
The duplex motor is driven in forward direction (in the paper exit direction) for 30 sec.
During the process, the display section displays the sub code.
After completion of the process, the machine goes into the sub code input standby mode.
When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
The duplex motor is driven in reverse direction for 30 sec.
During the process, the display section displays the sub code.
After completion of the process, the machine goes into the sub code input standby mode.
When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
When any key input is made, it is displayed on the display section.
When the [START] key is pressed, the set code data are acquired and stored in the EEPROM, and
the machine goes into the sub code input standby mode.
When, however, the [START] key is pressed outside the set range, it is not assured.
Set range: 1 - 13
At that time, when the [Interrupt] key is pressed, the data are not rewritten and the machine goes into
the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated without rewriting the data.
When any key input is made, it is displayed on the display section. When the [START] key is pressed,
the set code data are acquired and stored in the EEPROM, and the machine goes into the sub code
input standby mode.
Set range: 50 ~ 76
(Change quantity 1
1-2 phase 3 steps)
At that time, when the [Interrupt] key is pressed, the data are not rewritten and the machine goes into
the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated without rewriting the data.
When the [START] key is pressed, the toner motor is driven for 30 sec.
After completion of the process, the machine goes into the main code input standby mode.
When the [Interrupt] key is pressed, the machine goes into the main code input standby mode.
*
Trouble to write into the EEPROM such as H trouble is canceled and hardware reset is
performed.
*
U2 trouble is canceled and hardware reset is performed.
When the [Start] key is pressed, the maintenance count value is cleared and "000000" is displayed.
(Alternate display of "000" and "000")
The current set maintenance cycle code is displayed (initial display), and the set data are stored.
Code
0
1
2
3
4
5
The current set maintenance cycle code is displayed (initial display), and the set data are stored.
Code
0
1
2
The maintenance counter value is displayed.
The copy quantity corresponding to the code that is set with SIM21-01 is displayed.
(For example: 50,000 sheets)
The LED of the latest jam position is lighted. Every time when the magnification ratio display key is
pressed, the jam memory data is acquired sequentially from the latest. The jam position is judged by
the acquired data and the corresponding LED is lighted. The 7-seg display indicates the jam number.
At that time, "A" is displayed on the upper first digit. When the last one is displayed, the latest one will
be displayed again. Max. 30 jams from the latest are stored. When the [Interrupt] key is pressed, the
machine goes into the sub code input standby mode. When the [CA] key is pressed, the simulation is
terminated.
The jam total counter value is displayed.
The total counter value is displayed.
The developing counter data is acquired and displayed on the 7-seg display.
When the [Interrupt] key is pressed, the machine goes into the sub code input standby mode.
When the [CA] key is pressed, the simulation is terminated.
AR-M205 SIMULATIONS 7-6
Details of operation
Default: 4
Default: 50
Setting
5,000 sheets
7,500 sheets
10,000 sheets
25,000 sheets
50,000 sheets
* Default
Free (999,999 sheets)
Setting
5,000 sheets
* Default
10,000 sheets
Free (999,999 sheets)
Advertisement
