Safety and Precautions: Thank you for purchasing the new SAMSUNG digital satellite receiver. For your safety and proper operation of your receiver, please take time reading this manual fully before installing and operating the receiver. Safety notice: DANGER! HIGH VOLTAGE! RISK OF ELECTRIC SHOCK! Lethal voltages are present inside the unit.
Accessories: User Manual: 1 Batteries: 2 UHF TV cable: 1 Remote Control Unit: 1 R A D I O T V S A T LANG I N FO M U T E V O L V O L M E N U S I G N A L HELP...
System Connection: Please unplug all unites from mains outlet before installation. Once all connections are made please check again before connecting the equipment to the mains outlet. The following shows a typical installation of a satellite receiver. If you require further assistance for the installation of your satellite receiver, please contact your local distributor.
Front Panel: A. Standby: To switch the receiver on / off. B. Menu: To enter the main menu. C. Volume +/-: To increase or decrease volume level. D. Exit: To back step or exit from menu. E. Display: Displays channel mode and channel number (see below*). F.
Rear Panel Please refer to the diagram above for all the connection possibilities of your receiver. Do not connect the unit to the mains socket until all other connections have been made and checked. IF Input: Connect the cable from your dish to this connector. Loop Out: If you have a second satellite receiver, connect the second satellite receiver’s LNB input to this connector.
Remote Control Unit: By-Pass SCART priority VCR loop through Display radio channel list Display TV channel list To switch your receiver on from stand by or off to stand by To change volume, or to move cursor left, right in menu To select menu option, or to updated on entry Programme Guide :...
Quick Start: After initialisation, the Language selection screen will be displayed. By using the LEFT/RIGHT keys, you may select the different menu languages available. Once you have selected the desired menu language, press OK to continue with set-up. After selecting the menu language, the receiver will display the Channel Tuning Menu: (Menu, Channel Setup, OK) Preset Entry: Move the cursor to highlight the “Satellite”...
Downloading Channels: With a “Signal Found” message displayed the signal meters in the Channel Tuning Menu,and depending on whether you have selected a Satellite or Bouquet search. Press the OK key to begin auto search (Satellite, Network or Bouquet). A uto C hannel Search TV channels Searching 11.381 GHz …...
Viewing your channels: There are several ways to access the stored channels: Using the UP/DOWN keys on the remote handset to access the channels sequentially. Using the numeric keys (0-9) by typing the channel number to access the channels directly. Using the TV key on your handset to display the TV channel list.
Favourite Channels : Before you can use the “Favourite Channels List ” , you must first add your favourite channels into the favourites list. Please refer to the instructions below: 1. In view mode press the TV button to display the TV channel list. 2.
Selecting different audio channels: In digital satellite broadcasts, multiple audio languages can be simultaneously transmitted by the programme provider. Default audio setting: The user can first select a default audio language via the “Preferences” menu for the receiver. Once the default audio language has been stored, all newly found TV/Radio channels will then be stored with the selected default audio language.
At any time you can check the memory status on you receiver. The indicator shows the amount of receiver memory used by the stored channels. Press: Menu, Channel Setup, Memory Status : Memory Used SAMSUNG Use INFO key for diagnostic info Pic. Size: Frames/Sec: Asp. Ratio:...
Changing the PIN: The factory default PIN is set to: 0000. At any time the user may change this PIN code by accessing the “Change PIN” menu: Channel Lock Menu Lock Enter new PIN: Confirm: Lock/Unlock Channels Change PIN Note: Channel Lock is only effective if Installation/Channel Setup menus are also locked with Menu Lock To change the PIN code, enter in the new PIN into the New PIN box and re-enter the same PIN again...
Advanced users guide: Tuning to different channel frequencies: If the satellite you desire is not in the Preset listing, or you want to tune the receiver to a different set of channels, please follow the instructions below: To access the tuning menu, press the Menu key: Move the cursor to Channel Setup and press OK.
Tuning Modes: Auto Tuning From the select frequencies, the receiver will automatically search for all other frequencies within the tuning range and downloads them automatically into the receiver. Once the channels have been downloaded, all the TV and Radio channels will be displayed separately allowing the user to inspect them and decide whether they are to be stored or aborted.
Setup Satellite: If your desired satellite position is not on the Preset List, you can manually edit an existing satellite or add a new satellite name to the preset list. To add a new satellite to your list, you must first enter the channel tuning mode: Press Menu, Channel Setup, OK: From the Channel tuning menu press F1 to enter manual tuner mode.
Editing channels: Should you wish to modify or view details of a particular channel, you may do so by using the Edit Channel Details menu. Please note that apart from editing the channel name, editing any of the channel parameters will cause the channel to either be lost or changed (different audio/video).
Sort Free to Air Channels : This function automatically separates the scrambled channels from the free-to-air channels by actually checking each channel for video and audio. The user first decides whether to sort TV or Radio channels (or both at the same time), and then selects whether to delete the scrambled channels or simply move them to the end of the channel list.
Reset to factory defaults section in this manual. you may select individual channels for deletion. you may delete all channels in one operation. TV Channels TV 124 SAMSUNG Warning Radio List radio channels 1 Sky 1...
Installation: LNB: The installation menu provides access to LNB settings and features. These can expand the receivers capabilities as well as customising the receiver to your preference. Press Menu and select Installation to access the Installation menu: High DiSEqC Tone LNB Power DiSEqC 1.0 The default LNB setting is as per the diagram above.
TV/VCR settings: The TV/VCR menu contains various options that allow you to configure the receiver to suit your system: Press Menu, select Installation to access the TV/VCR Menu: TV Type UHF Channel Enable TV SCART RGB Enable TV SCART S-Video Enable VCR SCART S-Video The following options are available: TV Type:...
Preferences: This menu allows you to customise the receiver to suit your individual needs. To access the Preferences menu: Press Menu, select system. Select Menu Language: You may change the default menu language. The number of languages available depends on the receiver’s software version. EPG Type: You can change the Electronic Programme Guide format between FULL EPG or...
Reset to factory defaults: The Reset To Factory Defaults option is provided to enable the user to completely reset the receiver. Unlike the Clear All Channel Information option which allows the user to clear only the channel list, the Reset To Factory Defaults option will clear all changes made by the user, including Installation, Channel Setup and Parental Control changes.
Trouble shooting: If you suspect there is a fault with your receiver, please check the following trouble shooting guide before calling an authorised service agent. Warning! Under no circumstances attempt to repair the receiver yourself. Tampering with the receiver may result in fatal electric shock and will invalidate your warranty. Symptom: No receiver display Receiver is ON, but no picture or sound...
Technical Specifications: Electrical Specification Video Inputs: Video Outputs: Audio Inputs: Audio Outputs: Mains power: Connectors 4 x Phono/RCA: RS232: Modulator/Bypass: Satellite IF input: Satellite IF loop out: Tuner Loop though Digital tuner with LNB input, and loop output Full power loop through supported Frequency Range at LNB input: Input connector: Impedance:...
Page 29
Transport, A/V Decoding Demultiplexor: PID Filters: PCR recovery: Video Decoder: Bitstreams Supported: Video Resolution: Video Memory: Audio Decoder: Type: Layers: Audio Modes: Output Sample Rates Supported: Data rates supported PAL/NTSC Encoder: Supported Outputs: UHF/VHF Modulator: Tuning Range: (UHF): (VHF): Processor and memory System CPU: RAM: ROM:...