Subscribe to Our Youtube Channel
Related Manuals for Lytx DC-ACW-01
Summary of Contents for Lytx DC-ACW-01
- Page 1 Aux Camera Quick Start Guide Model List: Wi Fi Model Ethernet Model DC-ACW-01 DC-ACE-01 Side Mount Rear Mount DC-ACW-02 DC-ACE-02...
- Page 2 * It can achieve up to a speed of 72.2Mbps with single stream in 802.11n draft, 54Mbps as specified in IEEE 802.11g, or 11Mbps for IEEE 802.11b to connect to the wireless LAN. 1.1 Needed information for accessing to WiFi Model : DC-ACW-01 & DC-ACW-02 SSID ( last 6 digit follow...
-
Page 3: Side Mounting
AI IP Camera Quick Start Guide 1.2 Appearance Description and Device overview. The overview of the aux camera is shown below: Side Mounting Hose Clamp*2 Rear Clip Front Clip Aux Cam... -
Page 4: Rear Mounting
AI IP Camera Quick Start Guide Rear Mounting Rear Frame Plate Rear Clip Front Clip Aux Cam... - Page 5 AI IP Camera Quick Start Guide 1.3 Cable Interface M12 Ethernet D-Coded Cable for Video Signal Pin 1: TxData+ Pin 2: RxData+ Pin 3: TxData- Pin 4: RxData- 2 bare wire power cables Red wire: Provides primary power and must be connected to a continuous power source.
- Page 6 AI IP Camera Quick Start Guide 1.4 Required Tools In addition to all guides and reference documents that you should read before beginning installation, the following tools are required for installation: Wire cutter Tape measure Wire crimper ...
-
Page 7: Installation
AI IP Camera Quick Start Guide 2. Installation 2.1 Note The following materials are included in package. Make sure the device in the package is in good condition and all the assembly parts are included. 2.2 Packing list... - Page 8 AI IP Camera Quick Start Guide 2.3 Caution Please do not lift a camera by its cable. (NG) Please do not open the cover.
- Page 9 AI IP Camera Quick Start Guide 2.4 Mounting Location Recommendations Side Mounting Rear Mounting...
- Page 10 AI IP Camera Quick Start Guide 2.5 Install Side Mounting Screwdriver used in the metal hose clamp Angle Adjustment of side mounting. How to adjust the Aux camera when user had been fixed into the bracket of back mirror? First of all, using a Phillips screwdriver to release the Phillips screw A, Then user can adjust the angle, after done, meantime tightens the screws A.
- Page 11 AI IP Camera Quick Start Guide 2.6 Install Rear Mounting First of all, Use a Phillips screwdriver to release the Phillips screw A of both side. And tilting the camera to -90∘. Meantime user can see the hole of installation from top view. User can screw the screws B into the plate to fix entire camera, after done, user can adjust the angle for needing.
- Page 12 AI IP Camera Quick Start Guide 2.7 Cable connection For Wi-Fi Model, power-only installations: Red: Connect to 12V CONSTANT power source. Black: Connect to clean CHASSIS GROUND. Ground...
- Page 13 AI IP Camera Quick Start Guide For Ethernet Model, Video cable installation First of all, follow the power-cable installation to connect the power-cable. Then, connect the video cable and checking the length of cable, If necessary, use the extension cable to add the cable for your need. Mount the number O-ring for the waterproof connector onto the video cable port and install the remaining components of the waterproof connector in the sequence shown below.
- Page 14 AI IP Camera Quick Start Guide 2.8 Cable waterproof and insulation Please make sure the cable of all cannot be out of vehicle, and do not touch the rain or any water, If It cannot be prevent, please make sure get the waterproof as below shown.
- Page 15 AI IP Camera Quick Start Guide 2.9 Reset Button Use the Phillips screwdriver to remove the bottom cover of camera. This button is hidden in the bracket. Normally, the user will not see the reset button. When the user need to use this button. First of all, open the bracket, then you can see the button.
- Page 16 AI IP Camera Quick Start Guide 3. Check Item Please confirm the following to ensure that the equipment is installed correctly. Check Item Result All screw fully tightened The camera is securely installed to the mount or wall The ambient temperature meets the device specifications. Insulation and waterproofing measures have been taken to protect cables installed in humid environments, and the drip loops are in correct positions.
- Page 17 AI IP Camera Quick Start Guide...
-
Page 18: Fcc Caution
AI IP Camera Quick Start Guide FCC CAUTION General caution (applicable to all products); Class A: (Section 15.105) FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 19 AI IP Camera Quick Start Guide (Section 15.21) CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. Labeling ( Section 15.19)(a)(3) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 20 End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. “Hereby, Lytx , declares that this IP Auxiliary Camera is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.”...
Need help?
Do you have a question about the DC-ACW-01 and is the answer not in the manual?
Questions and answers