Cleaning The Unit; Troubleshooting - Vitek VT-8552 Instruction Manual

ENGLISH
Unpack the unit completely and remove any
–
advertising stickers that can prevent the unit
operation.
Check the unit for damages; do not use it in
–
case of damages.
Before switching on, make sure that the oper-
–
ating voltage of the power adapter corre-
sponds to voltage of your mains.
SWITCHING ON
Place the unit on a flat steady and dry surface.
–
When using the unit in the vertical position,
–
place it so that the electrostatic collector (2)
is at the bottom.
Insert the power adapter (7) cord connector
–
into the connection socket (3).
Plug the power adapter (7) into the mains.
–
Switch the unit on by pressing the "ON/OFF" but-
–
ton (6), the button (6) illumination will light up.
To switch the fan mode on, press the button (5)
–
"FAN", the button (5) illumination will light up.
To switch the unit off, press the "ON/OFF"
–
button (6), the unit will be switched off and the
illumination of buttons (5, 6) will go out.
The air purifier can operate for a long time, but,
–
as when operating any other electric appli-
ance, you have to follow the safety regulations:
unplug the unit when you don't need to use it.
Note:
If the electrostatic collector (2) is not installed or
–
installed improperly, the unit will not switch on.
Soft crackling during the unit operation is
–
connected with high relative air humidity in
the room, it is normal.

CLEANING THE UNIT

Body
Regularly clean the grids (1 and 4), you can
–
use a vacuum cleaner for cleaning them.

TROUBLESHOOTING

Problem Possible causes
The unit 1. The power adapter is not connected
would not to the mains. The power adapter
switch on connector is not connected to the
socket (3).
2. No voltage in the mains.
3. The electrostatic collector is not
installed or installed improperly.
4. Malfunction of the unit
IM VT-8552.indd 4
To clean the coal filter, remove the grid (4),
–
having pressed the grid lock. Remove the coal
filter (pic. 1).
Use a compressed air bottle to blow through
–
the coal filter (pic. 2).
Install the coal filter and the grid (4) back to
–
their places.
Wipe the unit body with a slightly damp cloth
–
and then wipe it dry.
Never immerse the unit into water or other
–
liquids.
Do not use abrasives and solvents to clean
–
the unit body.
Cleaning the electrostatic collector (2)
It is recommended to clean the electrostatic col-
lector (2) plates once a week.
Disconnect the power adapter from the
–
mains.
Remove the electrostatic collector (2), pull-
–
ing it by the handle (pic. 3). Do not touch
the plates until you remove the remaining
static charge. To do this, let the plates touch
any grounded object, such as water pipe or
tap.
Wipe the plates with a slightly damp cloth to
–
remove dust particles (pic. 4); dry the electro-
static collector for some time. Before installa-
tion, make sure that the electrostatic collector
plates are completely dry.
Install the electrostatic collector (2) back to its
–
installation place.
STORAGE
•
Clean and dry the unit body and the electro-
static collector before taking the unit away for
long storage.
•
Keep the unit in a dry cool place away from
children and disabled persons.
Solution
1. Plug the power adapter into the mains.
Insert the power adapter connector into
the connection socket (3).
2. To check, plug another appliance
into the same socket.
3. Check whether the electrostatic
collector is installed properly.
4. Apply to an authorized service center
for repairing the unit.
4
21.06.2018 17:26:15