Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for studiobricks One
Summary of Contents for studiobricks One
- Page 1 One, OnePlus, & OneXXL Assembling guide Last update | January 2022...
- Page 2 During unpacking, remove the highest parts and those IMPORTANT! Please note that no part of the cabin on top of others, first. Alternate parts on one side and should touch the building except for the feet. Leave at least another to ensure the stability of the packaging. Any heavy...
- Page 3 Organization Diferences between Studiobricks One, One Plus and One XXL Assembly Platform setup for Studiobricks One XXL Building the structure for Studiobricks One XXL 9 Platform setup for Studiobricks One/Plus Building the structure for Studiobricks One/Plus 12 Common steps Finishing...
-
Page 4: Before The Assembly
Before the assembly 1. Starting 1.1 Delivery Your Studiobricks One booth will arrive in a box. NOTE! If you detect any damages on the box during delivery please record these damages on the shipping documents. In case of damage a claim for reimbursement can be done by the insurance company. - Page 5 Before the assembly 1.3 Parts List of parts for Studiobricks One and One Plus: List of parts for Studiobricks One XXL: Bricks Bricks Floor (with 8 battens) Floor ring (with 8 battens) Silentblocks Studiobricks One/One Plus Silentblocks Floor carpet piece...
- Page 6 Before the assembly 1.4 Tools To build this booth you will need the following tools: a rubber mallet, snap blade utility knife, a screwdriver, a spirit level and a stepladder. 1.5 Organization Please keep in hand all tools that will be needed during the assembly.
- Page 7 Studiobricks One models have the same, therefore the same assembling instructions, except for some small differeneces: 1) The Studiobricks One Plus is the same as the Studiobricks One, but with some 30 cm. 2) The Studiobricks One XXL is the same as the...
- Page 8 The Studiobricks One models are equipped with silentblocks on the bottom of the ring floor piece. Stack a felt piece in each silentblock to prevent them from staining and denting the floor over time.
- Page 9 2.2 Start brick: building the structure Studiobricks One XXL You will now go on slotting all the panels in numerical order and clockwise. It´s easier if you slot in panel A5 a bit later. brick: We advise to tilt the piece a bit before placing it in place.
- Page 10 Assembly Floor Floor carpet panels: carpet panels Once you’ve completed level A except for A4 and A5 brick it’s time to place the 3 panels that make up the floor. Like the wall bricks, the floor panels are made of sound isolating materials to prevent sound from scaping downwards.
-
Page 11: Platform Setup
IMPORTANT! The floor and the ceiling frame come together, make sure to separate them before you start assembling. The Studiobricks ONEs booth are equipped with silentblocks for optimal acoustics in the bottom of the floor piece. Stack a felt piece in each silentblock to... - Page 12 Assembly 2.4 Building the brick: structure Studiobricks One & One Plus You will now go on slotting all the panels in numerical order and clockwise. It´s easier if you slot in panel A5 a bit later. brick: We advise to tilt the piece a bit before placing it in place.
- Page 13 Assembly Floor carpet panel: l batten: Floor carpet panel Once you’ve completed level A except for A4 and A5 brick, put the floor carpet piece. Like the wall bricks, the floor panel is made of sound isolating materials to prevent sound from scaping downwards.
- Page 14 Assembly 2.5 Common Vertical battens steps Vertical battens: Insert the 3 vertical battens between A1, A2, A3 and A4 bricks as seen in the image on the left. Adjust securely with a rubber mallet. The battens should be inserted with the middle line pointing in the same direction as the wall.
- Page 15 Assembly Self-adhesive rubber pieces: Rubber pieces Remove the paper that protects the adhesive from the 3 pieces of rubber. Then, place the self-adhesive rubber pieces covering the visible part of the batten.
- Page 16 B: Shorter ones go on the back corners. • C: Second longest goes to the right of the door. Studiobricks One XXL don’t uses “A” battens. In instead of this, XXL model uses 1 “B” batten + 1 horizontal batten.
- Page 17 Assembly Level B: brick Now we can start building level B. Make sure dowels fit perfectly. On this floor it is very important to fit the brick completely straight so as not to force them. B1 brick: Start with the B1 brick. Place it on the left side of the entrance door as indicated by the image.
- Page 18 B2 bricks) in the frontside; and 1 corner batten type B (joining B1 and B2 bricks) in the backside as shown in the image. Studiobricks One XXL don’t uses “A” battens. In instead of this, XXL model uses 1 “B” batten + 1 horizontal batten.
- Page 19 Assembly Door: Outside booth Door handle must be first installed before the rest of the booth due to safety reasons as the door should remain closed during the assembly. Assembly of the door handle: We recommend that you use a manual screwdriver to avoid possible scratches on the door frame.
- Page 20 Assembly Acoustic sealing: Once installed, to get the best possible insulation the handle must be turned up.
-
Page 21: Door Installation
Door installation: Door As the door is very heavy we recommend assistance for this step. At least one operator should be inside during installation of the door. The next step is to place the door. While an operator holds the left side of the booth, present the door and drop it until it fits perfectly. - Page 22 Assembly A5 brick: Place brick A5 as seen in the image to the left, fitting it with the A4 brick and the door. Now level A is complete. Vertical battens: Insert the vertical battens between A4 and A5 bricks as seen in the image on the left. Adjust securely with a rubber mallet.
- Page 23 Assembly Corner batten: Now we will place 1 corner batten type C (joining A4 and A5 bricks) in the frontside as shown in the image. Adjust securely with a rubber mallet. B4 brick: Corner batten Place brick B4 fitting it with the B3 brick. B5 brick: Place brick B5 fitting it with the B4 brick and the door.
- Page 24 Assembly Vertical battens: Vertical battens Insert the vertical battens between B4 and B5 bricks as seen in the image on the left. Adjust securely with a rubber mallet. The battens should be inserted with the middle line pointing in the same direction as the wall. Self-adhesive rubber pieces: Remove the paper that protects the adhesive from 4 pieces of rubber.
- Page 25 Assembly Level C: brick Now we can start building level C. Make sure dowels fit perfectly. On this floor it is very important to fit the brick completely straight so as not to force them. C1 brick: Start with the C1 brick. Place it on the left side of the entrance door as indicated by the image.
- Page 26 Assembly C3 brick: Place brick C3 as seen in the image, fitting it with the C2 brick. C4 brick: brick Place brick C3 as seen in the image, fitting it with the C2 brick. brick...
- Page 27 Assembly C5 brick: Place brick C5 fitting it with the C4 brick and the door. Vertical battens: brick Insert the 4 vertical battens on level C as seen in the image on the left. Adjust securely with a rubber mallet. The battens should be inserted with the middle line pointing in the same direction as the wall.
- Page 28 Corner battens Place the corner battens (joining all bricks on level C) as shown in the image. Studiobricks One XXL don’t uses “A” battens. In instead of this, XXL model uses 1 “B” batten + 1 horizontal batten. Adjust securely with a rubber mallet.
- Page 29 Assembly D1 brick: Place brick D1 fitting it with the C1 brick and the door. D2 brick: brick Place brick D2 fitting it with the D1 brick. brick...
- Page 30 Assembly D3 brick: Place brick D3 as seen in the image, fitting it with the D2 brick. brick D4 brick: Place brick D4 as seen in the image, fitting it with the D3 brick. brick...
- Page 31 Assembly D5 brick: Place brick D5 fitting it with the D4 brick and the door. brick Vertical battens: Insert the vertical battens on level D as seen in the image on the left. Adjust securely with a rubber mallet. The battens should be inserted with the middle line pointing in the same direction as the wall.
- Page 32 Corner battens Place the corner battens (joining all bricks on level D) as shown in the image. Studiobricks One XXL don’t uses “A” battens. In instead of this, XXL model uses 1 “B” batten + 1 horizontal batten. Adjust securely with a rubber mallet.
- Page 33 Assembly Roof ring: With the help of one or more persons, position the roof ring on top of the D bricks. Carefully slide it into position and press until the battens snap into place. Adjust securely with a rubber mallet.
-
Page 34: Cable Port
Assembly 2.6 Finishing Cable port: 1 - outside A2 brick: First put in the trim cable gland into the cable port hole. It’s located outwards A2 brick. Remove the cap from the trim cable gland. Put it back once the cable is passed by pressing until you hear a click. -
Page 35: Ventilation Kit
Assembly Ventilation kit: The ventilator sits inside the booth. To install it put the two provided screws into the holes and tighten them leaving half a centimetre stand out. Fix the ventilator to the wall. The small white air vent sit outside the A2 brick. - Page 36 Assembly Voltage transformer (USA only): If you are a customer from the U.S. you will find a voltage transformer to be able to connect the ventilation kit to 110V. You have to configure its input and output parameters following this steps: 1: Switch the input selection switch in the back of the transformer to 110V.
- Page 37 Assembly Mounting the additional table with- out hinges (for VO Edition package option or desk as an option): If you have bought the additional table or the VO Edition package you will see that there is a gap in the absorbers of the A2 brick that clearly indicate the position of the table.
- Page 38 If you purchased your booth without a Bass Trap and decide to install one later, you will have to remove the absorber from the D4 brick using a flat screwdriver to pry and release the clips.
- Page 39 The switch cable is supplied separately (you will find it in the small box). Connect the cable to the led light. You will find the triple connector at one end of the light. A good way to hide the cable is to pass it through the...
- Page 40 Assembly How to install the wall pole and pole halter on a Studiobricks One Plus/XXL (for VO Edition): Voice Over Edition comes with a preinstalled Wall Poll on brick B3. The next step is to place the Pole Halter to the desired height.
- Page 41 Assembly Lacquer: We provide you with a small bottle of lacquer in case you need to fix some small scratches which can occur during assembling.
- Page 42 Assembly 2.7 Moving your Studiobricks One booth: ROOF ROOF RING FLOOR RING FLOOR...
- Page 43 Last update | January 2022...
Need help?
Do you have a question about the One and is the answer not in the manual?
Questions and answers