Specifications - Peavey IMPULSE 12 D Operating Manual

Enclosure: Peavey Impulse
Frequency response: 52 Hz to 20 kHz
Low frequency limit (-3 dB point): 60 Hz
Usable low frequency limit (-10 dB
point): 52 Hz
Internal power amplifiers (@120 VAC line):
Woofer - 1200 watts peak available
power Continuous Power: 550 watts
@ less than 1% distortion
Tweeter - 150 watts peak available
power Continuous Power: 75 watts @
less than 1% distortion.
Nominal sensitivity (1W @1M, swept
sine input in anechoic environment):
100 dB (average)
Maximum sound pressure level: 131 dB
music peak
Nominal radiation angles: 100˚
horizontal by 30˚ vertical
Transducer complement: 12"
Neodymium Dual Voice Coil Scorpion
woofer, Model SDC1288 and RD
with 4.75" long aluminum composite
ribbon tweeter
Box tuning frequency (Fbox): 61 Hz
Electroacoustic crossover
frequency: 2,000 Hz
Crossover type: Internal Electronic
two-way crossover with driver EQ, level
matching, bass boost and subsonic
filtering.
Crossover Slopes: 24 dB/octave
(fourth order) low pass, 24dB/octave
(fourth order) high pass, both with
staggered poles and driver EQ. Unit has
horn spatially aligned with woofer, so
there is no need for phase alignment or
time delay of the signals.
Electronic Input Impedance
(Nominal):
10 k ohms unbalanced
20 k ohms balanced line level
2.4 k ohms balanced mic level
Impulse

SPECIFICATIONS

® 12D Input Connections: Input 1: One
combo female XLR/ 1/4" phone jack
providing balanced operation, with
switch-selectable mic- or line-level
sensitivity.
One 3-conductor balanced Euro-style
jack connector
Input 2: One combo female XLR/
1/4" phone jack providing balanced
operation, with switch-selectable mic-
or line-level sensitivity.
Two RCA phono-type jacks, which are
buffered and mixed to monophonic
for a summed signal. These are NOT a
stereo input, as the Impulse
single full-range sound source.
Output Connections: One male XLR
balanced output, one ¼" TRS balanced
phone-type jack, one 3-conductor
balanced Euro-style jack connector.
Cabinet material: Injection-molded
polypropylene with internal ribbing
and bracing, and with textured finish.
Molded material is dark gray, as is the
metal grille. Available in a white version
as well.
Mounting: Subwoofer pole-mounting
®
or speaker stand via molded-in pole
™ 2.6
mount, flying via Versamount
4 rubber feet for floor or stage use.
Dimensions: H x W x D
Front: 24.89" (63.2 cm) x 15.63" (39.7
cm) x 15.38" (39.1 cm)
Rear: H x W 23.13" (58.8 cm) x 7.50"
(19.1 cm), 13.50" (34.3 cm) at second
angle break
Weight: 39 lbs. (17.7 kg)
12D
®
ELECTRONICS AND AMPLIFIER
SPECIFICATIONS:
Electronic input impedance
(nominal): Balanced inputs: 20 k ohms
line level sensitivity selected, 2.4 k
ohms mic level sensitivity selected
Mic switch sensitivity Increase: 30 dB
Infrasonic filter protection: 36 dB/
octave roll-off
Woofer Drive Mode: Servo-controlled
feedback for lower distortion and
® 12D is a
precise signal tracking.
Push-button EQ Modes of DynaQ:
Flat frequency response
Filtered roll-off of high and low
frequencies (Speech Mode)
Dynamic boost to high frequencies
(Contour)
Dynamic boost to both high and low
frequencies, (Fletcher-Munson type
compensation, Contour and Bass
enhancer)
Sleep Mode: When Sleep Switch
is engaged, unit will shut down the
electronics after 16 minutes of no signal
™ 70+, and
input. Unit will come back on within 3-5
seconds of an applied signal.
Nominal amplifier frequency
response: +0, -1 dB from 10 Hz to 20 kHz
Hum and noise: Greater than 90 dB
below rated power
DDT dynamic range: Greater than 22 dB
THD and IM: Typically less than 0.1 %
Damping factor: Greater than 100 @
1000 Hz, 8 ohms
Power requirements of Peavey
Impulse
Nominal 700 watts, 120 VAC, 60 Hz
®
12D system (domestic):