Effect Settings For Audio Input - Korg sampler Basic Manual

Effect settings for AUDIO INPUT

In Program, Combination, Sequencer, Song Play, and Disk
modes, external audio sources can be input from the
AUDIO INPUT 1, 2, S/P DIF IN, and mLAN (if the EXB-
mLAN option is installed) jacks, or from an audio CD
inserted in the CDRW-1 option (if installed), and pro-
cessed by the TRITON STUDIO's effects. In these modes,
the insert effects, master effects, and master EQ can be
used. Settings for the external audio input from each
AUDIO INPUT 1, 2, S/P DIF IN, and mLAN (if the EXB-
mLAN option is installed) jack can be made in "Input
(COMBI, PROG, SEQ, S.PLAY, DISK)." Normally, you will
make these settings in the Global mode P0: Basic Setup,
Input/Sampling page, but you can also make them in
Combination, Program, Sequencer, or Disk modes.
In these modes, you can apply the TRITON STUDIO's
effects to the external audio signals from each jack and
sample the result, or use the TRITON STUDIO as a 6-in
(AUDIO INPUT 1, 2, S/P DIF IN L, R, mLAN 1, 2) 6-out
effect processor. You can also use it as a vocoder effect
(093: Vocoder) in which internal sounds are controlled by
an external mic input.
Routing
In Program, Combination, Sequencer, Song Play, and Disk
modes (i.e., in other than Sampling mode), the routing of
the external audio input signals from the various jacks is
specified by "BUS (IFX/Indiv.) Select."
1 Use "Input (COMBI, PROG, SEQ, S.PLAY, DISK)" to
select the source that you want to input.
This setting can be made in any of the following pages.
If you want to save the edited settings into internal
memory, you must write them. Use the Global mode
page menu command "Write Global Settings."
Program, Combination P0: Play, Sampling page
Sequencer P0: Play, Sampling page
Global P0: Basic Setup, Input/Sampling
page
Disk Play Audio CD page
Input-related settings are shared between all of the
above modes. For each input source that you select in
"Input (COMBI, PROG, SEQ, S.PLAY, DISK)," a rout-
ing can be specified independently. If desired, you
may input simultaneously from all input sources.
If you want to make these settings in Global mode,
move to Global mode from the mode (other than
Sampling mode) in which you will be inputting the
external audio signals. If you move from Sampling
mode to Global mode, the Input (SAMPLING) settings
of Sampling mode will be maintained, and it will not
be possible to view the settings of this page.
These settings are ignored in Sampling mode. Audio
input settings for Sampling mode are made in a simi-
lar way, in Sampling P0: Recording, Input/Setup
page Input (SAMPLING).
When you apply effects to external input signals from
the AUDIO IN 1, 2, S/P DIF IN, and mLAN inputs,
oscillation may be heard depending on the type of
effect and the parameter settings of the effect. If this
occurs, adjust the input level, output level, and effect
parameters. Particular care should be taken when
using high-gain effects.
2 Set the parameters for Input1 and 2.
Input1 and 2 correspond to the following inputs.
Analog AUDIO INPUT
S/P DIF S/P DIF
mLAN mLAN
"Level": Sets the level of the input signal that you
selected in "Input (COMBI, PROG, SEQ, S.PLAY,
DISK)." Normally you will set this to 127. If the sound
is distorted even though you lower this setting signifi-
cantly, it is possible that the sound is distorting before
the AD converter. Adjust the [LEVEL] knob or the out-
put level of the external audio source.
"Pan": Sets the pan of the input signal that you
selected in "Input." When inputting a stereo audio
source, you will normally set Input1 to L000, and
Input2 to R127 (or Input1 to R127 and Input2 to L000).
When inputting a mono audio source, you will nor-
mally set this to C064.
"BUS (IFX/Indiv.) Select": In the same way as when
making settings for the oscillator(s) of a program, Spec-
ifies the bus to which each external audio input will be
sent. ( p.140)
"Send1 (to MFX1)," "Send2 (to MFX2)": In the same
way as when making settings for the oscillator(s) of a
program, sets the master effect send levels for each
external audio input. This can be set only if "BUS (IFX/
Indiv.) Select" is set to L/R or Off. ( p.141)
If "BUS (IFX/Indiv.) Select" is set to IFX1–5, the master
effect send levels are set by the "Send1" and "Send2"
parameters following the insert effect (in each Insert FX
page).
If "BUS (IFX/Indiv.) Select" has a setting other than
Off, and you raise the "Level" value, the external
audio source will be input to the TRITON STUDIO.
At this time if audio cables are connected to the rear
panel AUDIO INPUT 1 and 2 jacks, noise may be
input to the TRITON STUDIO via the AD converter
even if no audio input is actually present, and
depending on the settings, may be output from
AUDIO OUTPUT L/R, 1, 2, 3, or 4. If you will not be
using an external audio source, but are using only the
internal sounds of a program, combination, or song,
set "BUS (IFX/Indiv.) Select" to Off, or set "Level" to
0.
Similarly, if you will not be using the S/P DIF IN con-
nector or mLAN connector, set these inputs to "BUS
(IFX/Indiv.) Select" Off, or set their "Level" to 0.
If no audio cables are connected to the rear panel
AUDIO INPUT 1 and 2 jacks, the data that is input to
the TRITON STUDIO from the AD converter will be
set to zero, and no noise will be output.
1 Input1
2 Input2
Lch Input1
Rch Input2
1 Input1/Input2
2 Input1/Input2
143