Download  Print this page

Information Specifications - Kenwood VR-9070 Instruction Manual

Kenwood instruction manual audio video surround receiver
Hide thumbs

Advertisement

Specifications
AUDIO section
Rated power output during STEREO operation
100 watts per channel minimum RMS, both channels driven,
at 8 Ω from 20 Hz to 20 kHz with no more than 0.09% total
harmonic distortion. (FTC)
Effective power output during SURROUND operation
FRONT (20 ~ 20 kHz, 0.09 % T.H.D., at 8 Ω one channel driven)
............................................................................... 100 W + 100 W
CENTER (20 ~ 20 kHz, 0.09 % T.H.D., at 8 Ω one channel
driven) .................................................................................. 100 W
SURROUND (20 ~ 20 kHz, 0.7 % T.H.D., at 8 Ω one channel
driven) ................................................................... 100 W + 100 W
SURROUND BACK (20 ~ 20 kHz, 0.7 % T.H.D., at 8 Ω one
channel driven) .................................................... 100 W + 100 W
Total harmonic distortion ....................... 0.009 % (1 kHz, 50 W, 8 Ω)
Frequency response
CD/DVD .................................. 10 Hz ~ 100 kHz, +0 dB ~ –3.0 dB
PHONO 'RIAA' response .............. 40 Hz ~ 20 kHz, +1.5 dB ~ –3.0 dB
Maximum input level
PHONO (MM) .................................. 40 mV, 1 % T.H.D., at 1 kHz
Signal to noise ratio (IHF'66)
PHONO (MM) ........................................................................ 75 dB
CD/DVD ................................................................................. 95 dB
Input sensitivity / impedance
PHONO (MM) ........................................................... 4 mV / 47 kΩ
CD/DVD, MD/TAPE, AV AUX, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH
.............................................................................. 300 mV / 47 kΩ
Output level / impedance
TAPE REC ............................................................... 300 mV / 1 kΩ
PRE OUT (FRONT CHANNEL) ................................... 1 V / 500 Ω
PRE OUT (CENTER CHANNEL) ................................. 1 V / 500 Ω
PRE OUT (SURROUND CHANNEL) .......................... 1 V / 500 Ω
PRE OUT (SURROUND BACK CHANNEL) ............... 1 V / 500 Ω
PRE OUT (SUBWOOFER) .......................................... 1 V / 500 Ω
Tone control
BASS ................................................................ ±10 dB (at 100 Hz)
TREBLE ............................................................ ±10 dB (at 10 kHz)
Loudness control
VOLUME at –30 dB level ...................................... +6 dB (100 Hz)
DIGITAL AUDIO section
Sampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96 kHz
Input level / impedance / wave length
Optical .............................. –15 dBm ~ –24 dBm, 660 nm ±30 nm
Coaxial ................................................................... 0.5 Vp-p / 75 Ω
Output level / impedance / wave length
Optical .............................. –21 dBm ~ –15 dBm, 660 nm ±30 nm
Notes
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
52
EN
Caution : Read this page carefully to ensure safe
operation.
VIDEO section
VIDEO inputs / outputs
VIDEO (composite) .................................................. 1 Vp-p / 75 Ω
S VIDEO inputs /outputs
S VIDEO (luminance signal) ................................... 1 Vp-p / 75 Ω
S VIDEO (chrominance signal) ....................... 0.286 Vp-p / 75 Ω
COMPONENT VIDEO inputs /outputs
COMPONENT VIDEO (luminance signal) .............. 1 Vp-p / 75 Ω
COMPONENT VIDEO (CB/CR-signal) ............... 0.64 Vp-p / 75 Ω
FM tuner section
Tuning frequency range ................................. 87.5 MHz ~ 108.0 MHz
Usable sensitivity (MONO)
................. 1.3 µV (75 Ω)/ 13.2 dBf (75 kHz dev, SINAD 30 dB)
50 dB quieting sensitivity
STEREO .............................. 28 µV (75 Ω)/ 40.2 dBf (75 kHz dev)
Total harmonic distortion
MONO (1 kHz, 75 kHz dev) .......................... 0.5% (65 dBf input)
STEREO (1 kHz, 67.5 + 67.5 kHz dev) ......... 0.7% (65 dBf input)
Signal to noise ratio
MONO (1 kHz, 75 kHz dev) ........................ 75 dB (65 dBf input)
STEREO (1 kHz, 67.5 + 67.5 kHz dev) ....... 68 dB (65 dBf input)
Stereo separation (1 kHz) ........................................................... 40 dB
Selectivity (±400 kHz) ................................................................. 70 dB
Frequency response (30 Hz ~ 15 kHz) .................... +0.5 dB, –3.0 dB
AM tuner section
Tuning frequency range
...................................................................... 530 kHz ~ 1,700 kHz
Usable sensitivity (30% mod, S/N 20 dB)
........................................................................ 16 µV / (600 µV/m)
Signal to noise ratio (30% mod, 400 Hz)
.......................................................... 50 dB (60 dBµV EMF input)
GENERAL
Power consumption ................................................................... 3.4 A
Standby Power consumption ...................................... less than 1 W
AC outlet
SWITCHED ......................................... (total 150 W, 1.25 A max.)
Dimensions ..................................................... W : 440 mm (17-5/16")
Weight (Net) ................................................................ 12 kg (26.5 lb)
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer
to the model and serial numbers whenever you call upon your dealer for
information or service on this product.
Model __________________ Serial Number ________________________
H : 166 mm (6-9/16")
D : 396 mm (15-9/16")

Advertisement

Table of Contents
loading

  Related Manuals for Kenwood VR-9070