Download  Print this page

Control Re-Assigning Device Keys; Operating Other Components - Kenwood VR-9070 Instruction Manual

Kenwood instruction manual audio video surround receiver
Hide thumbs

Advertisement

Basic remote control operations for other components
4
Repeat step 3 three more times for the remaining digits. Use
"2" for the second digit, "3" for the third digit, and "4" for the
fourth digit.
5
To check the codes of your other components, repeat steps
1 through 4 , but substitute the appropriate key (i.e., DVD/
6CH, VIDEO 1, VIDEO 2, VIDEO 3, CD/DVD, MD/TAPE, PHONO,
AV AUX, TV MODE) for the component you are checking.
• As suggested earlier on, write down each of the four-digit code.
• PHONO key has to be re-assigned to another key before a setup
code can be programmed.
Re-assigning device keys
The remote control can be setup to control second TV or VCR, or any
combination of eight home entertainment components.
For example, to control the operation of two different VCR using the
remote control, the user need to re-assign the unused VIDEO 2 key to
operate the second VCR (VIDEO 1) as follows:
1
Press and hold the LEARN key until
release the LEARN key.
2
Press the Numeric key to enter 9 , 9 , 2 .
will blink twice.
3
Press VIDEO 1 key once, then press the VIDEO 2 key once.
• The user now can operate VIDEO 2 as a second VCR along with
VIDEO 1.
• Refer to the table in the previous page for the combination of
source keys and the other components assignment.
4
To re-assign other device keys, repeat steps 1 through 3 by
substituting the key sequence from the below chart for the
most popular components:
To re-assign key
Sequence
TV MODE as 2nd VIDEO 1 key LEARN 9 9 2 VIDEO 1
TV MODE as 2nd VIDEO 2 key LEARN 9 9 2 VIDEO 2
TV MODE as 2nd CD/DVD key LEARN 9 9 2 CD/DVD
TV MODE back to TV MODE key LEARN 9 9 2 TV MODE TV MODE
VIDEO 1 as 2nd TV MODE key LEARN 9 9 2 TV MODE VIDEO 1
VIDEO 1 as 2nd VIDEO 2 key LEARN 9 9 2 VIDEO 2 VIDEO 1
VIDEO 1 as 2nd CD/DVD key LEARN 9 9 2 CD/DVD VIDEO 1
VIDEO 1 back to VIDEO 1 key LEARN 9 9 2 VIDEO 1 VIDEO 1
5
To clear the re-assignment and reset the remote control to its
original operation mode:
1 Press and hold the LEARN key until
release the LEARN key.
2 Press the Numeric key to enter 9 , 9 , 2.
3 Press VIDEO 2 key twice.
• When a re-assignment is done,
choice. At that time, you will need to program the remote control
in order to control the new component.
• If an invalid key sequence is entered,
normal operation.
• When in Tuner mode, re-assignment is not available.
40
EN
blinks twice, then
·
Perform
TV MODE
TV MODE
TV MODE
blinks twice, then
will blink twice to confirm your
blink once and return to

Operating other components

This operation lets you operate the registered components.
Source keys
1
Use the Source keys to select the component you desire.
• Pressing the source keys also changes the input selector on the
receiver.
2
Press the SOURCE key.
• To return to the receiver operation mode, press the RCV MODE key.
3
Press the operation keys you desire.
The remote control mode remains at the selected input. If you
wish to operate another component, repeat step 2 or 3.
Resetting the Remote Control
• To initialize the remote control, press the LEARN key until the
blinks twice. Then press the Numeric key to enter 9, 8, 1. The
will blink twice.
SOURCE
(Source power)
y

Advertisement

Table of Contents
loading

  Related Manuals for Kenwood VR-9070