Symptoms And Treatment - Kenwood Sovereing DV-5700 Instruction Manual

Kenwood multiple dvd vcd cd player dv-5700 instruction manual
Hide thumbs Also See for Sovereing DV-5700:
Table of Contents

Advertisement

Symptoms and Treatment

Playback starts but the video is not output.
¶ The Pure Audio function is set to on.
¶ The input selection of the TV and/or AV amplifier is
incorrect or these devices are not turned on.
¶ Connection cords are connected improperly.
Playback starts but the audio is not output.
¶ The "Speaker Setting" is incorrect.
¶ The input selection of the TV and/or AV amplifier is
incorrect or these devices are not turned on.
¶ The volume of the TV and/or AV amplifier is not ad-
justed properly.
¶ Audio output cords are connected improperly.
The picture is disturbed during forward search or
reverse search.
¶ The picture disturbance during forward search or re-
verse is normal. This is not a malfunction.
The picture is not neat or the video or audio quality
is poor.
¶ Connection cords are connected improperly.
¶ A device generating noise is installed near the signal
path.
¶ The disc is dirty or damaged. To prevent this, remove
dirt and handle discs carefully so as not to damage
them.
¶ There may be condensation of dew on the optical
lenses. In this case, leave the player with power ON
for a few hours to dry up the condensation, then retry
operation.
It takes long time before playback starts.
¶ The disc type should be detected and motor rotation
stabilized before starting playback. This is normal and
not a malfunction.
72
A warning is displayed on the TV screen and play-
back is not possible.
¶ The reproduced video may be disturbed or audio may
be skipped when the disc surface is stained with fin-
gerprints or dirt. Clean the disc surface by wiping it in
the radial directions using a soft cloth.
¶ If the disc is placed obliquely or on another disc, place
the disc correctly.
¶ Playback may be unavailable due to viewing restric-
tion or region code problem.
The top and bottom edges of the picture are cut off.
¶ The video format of the played disc does not match
that of the connected TV.
VCD cannot be played with menu playback.
¶ Menu playback is not available when P.B.C. is Off or
the sequential play mode of the player is set to
"SEQ.2".
¶ Menu playback is possible only with P.B.C.-compat-
ible VCDs.
DVD VIDEO cannot be played.
¶ DVD VIDEO cannot be played when the sequential
mode of the player is set to "SEQ.2". Switch it to
"SEQ.1".
Subtitles are not displayed.
¶ Subtitles are not displayed when the played DVD does
not contain the recording of subtitles.
¶ The subtitle language is set to "Off".
Audio (or subtitle) language cannot be changed.
¶ The language cannot be switched when the played
DVD does not contain the recording of multiple au-
dio (or subtitle) languages.
Viewing angle cannot be changed.
¶ The viewing angle cannot be switched when the played
DVD does not contain the recording of multiple angles.
The viewing angle can neither be switched in part
where no angle is recorded.
Chapter 7: Other Information
The viewing restriction (Rating) cannot be changed.
¶ If you have lost the password, initialize the default
setting by the user to the factory setting as described
below.
While holding the 7 button on the main unit, press
the POWER button. When the display shows "INIT
OK!", switch the power on again.
The selected audio or subtitle languages is not
played.
¶ If the played DVD does not contain the default lan-
guage set by the user, the priority language specified
for the disc will be selected.
The TV screen does not show any message when a
button is pressed.
¶ If "On Screen Message" is set to "Off", switch it "On".
The messages in the menus are not displayed in the
selected language.
¶ If the played DVD does not contain the recording of
the default language set by the user, the priority lan-
guage specified for the disc will be selected.

Advertisement

Table of Contents
loading

Table of Contents