X'over Setting; Audio Preset Memory - Kenwood KDC-BT945U Instruction Manual

DSP Setup

X'Over Setting

Fine adjusting the following setting values
corresponding to the X'Over values set in the
section <Speaker Setting> (page
Display Item
"X'Over"
"Front" "FC"
"SLOPE"
"Rear" "FC"
"SLOPE"
"SubWoofer" "FC"
"SLOPE"
"PHASE"
* Function of KDC-X994/ KDC-X794
1
Select the source
Press the [SRC] button. Turn the [VOL] knob and
press it when the desired item is displayed.
Select a source other than "STANDBY".
✍ SRC Select mode 2: Pressing the [SRC] button
repeatedly switches source.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Enter X'Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "Detailed Setup"
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "Front", "Rear", or "SubWoofer".
5
Select the item you want to set
Operation type
Selects the item.
Adjust each item.
Set the value
44
|
KDC-X994/ KDC-BT945U/ KDC-X794/ KDC-MP745U
42).
Range
Front High Pass Filter
Through, 30*, 40, 50*, 60, 70, 80,
90*, 100, 120, 150, 180, 220, 250*
(Hz)
Front High Pass Slope
-6, -12, -18, -24 dB/Oct
Rear High Pass Filter
Through, 30*, 40, 50*, 60, 70, 80,
90*, 100, 120, 150, 180, 220, 250*
(Hz)
Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
Subwoofer Low Pass Filter
30*, 40, 50*, 60, 70, 80, 90*, 100,
120, 150, 180, 220, 250*, Through
(Hz)
Subwoofer Slope
-6, -12, -18, -24 dB/Oct
Subwoofer Phase
Reverse (180°)/ Normal (0°)
( : Factory setting)
>
"X'Over".
Operation
Turn the [VOL] knob.
Press the [4] or [¢] button.
Press the [VOL] button.
6
Repeat steps 3 to 4 to complete the X'Over
settings.
7
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.

Audio Preset Memory

Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
- Car Type Selection (page 42)
- Speaker Setting (page 42)
- Car Type Fine Adjustments (page 43)
- X'Over Setting (page 44)
- Manual Equalizer Control (page 39)
- Listening Position Selection (page 40)
- Listening Position Fine Adjustments (page 40)
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "Detailed Setup"
3
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
4
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "YES".
"Memory Completed" is displayed.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
• Register 6 patterns of Audio Preset Memory.
• Preset number "1":
When you press the Reset, all the sources will be the
setting value which is registered.
• Preset number "1" and "2":
The memory cannot be erased by the Reset button.
• This function cannot be registered when the iPod
Equalizer set in <Preset Equalizer curve Select> (page
> "Preset" > "Memory".
39).