Download  Print this page

Advertisement

Ninja ZX-10R
2006 Ninja ZX-10R
Racing Kit Manual
This manual contains only the information of the racing kit parts. Refer to the base
manual listed below for information of the original model.
Base Manual
Part Number
Ninja ZX-10R
99924-1365-01
Motorcycle Service Manual
© 2006 Kawasaki Heavy Industries, Ltd.
First Edition (1): Feb. 2, 2006

Advertisement

   Summary of Contents for Kawasaki NINJA ZX-10R

  • Page 1 This manual contains only the information of the racing kit parts. Refer to the base manual listed below for information of the original model. Base Manual Part Number Ninja ZX-10R 99924-1365-01 Motorcycle Service Manual © 2006 Kawasaki Heavy Industries, Ltd. First Edition (1): Feb. 2, 2006...
  • Page 3 Congratulation on your purchase of racing kit parts for the 2006 Ninja ZX-10R. This manual provides how to install racing kit parts for the 2006 Ninja ZX-10R and how to tune up basically. As for the basic knowledge, refer to the base Service Manual for the Ninja ZX-10R (P/No.
  • Page 4: Table Of Contents

    General Specifications ...3 Racing Kit Service Data ...5 Periodic Maintenance Chart...5 Engine Parts Installation ...7 Air Intake Parts ...7 Camshaft Chain Tensioner...8 Camshafts, Sprockets ...9 Cylinder Head ... 11 Cylinder Compression ...12 Pistons...13 Crankshaft Main Journal Bushings ...15 Connecting Rod Bolts ...17 Connecting Rod Big End Bushings...19 Clutch Adjustment (Back-Torque Limiter Setting) ...20 Transmission ...26...
  • Page 5: General Specifications

    13262-0135 13262-0183 Teeth (Out/In) Gear Ratio 13262-0136 13262-0171 Teeth (Out/In) Gear Ratio 2006 Ninja ZX-10R Racing 10°BTDC @1 100 r/min (rpm) Racing gasoline Racing oil Between upper and lower levels of oil level gauge. 1.611 (87/54) Type B 13127-0030 13262-0267...
  • Page 6 Input 3 Gear Selection Table 3rd Gear Gear Identification Slit Number Table Standard (Type A) Input Output Input Output Input Output Input Output Input Output Input Output Engine Sprocket 13144-0021 #520-16T 13144-0022 #520-17T 13262-0134 (19/21) 13262-0284 (19/21) 13262-0272 (16/21) Type B 4th Gear A (=C) 13262-0286 (19/20)
  • Page 7: Racing Kit Service Data

    These values show the specifications when standard cylinder head and gasket are used. Periodic Maintenance Chart The scheduled maintenance must be done in accordance with this chart to keep the motorcycle in good running condition. OPERATION Engine Clutch plate - - check*...
  • Page 8 OPERATION Connecting rod big end bearing - - check* Transmission gear, bearing - - check* Engine sprocket - - check* Coolant - - change Radiator hoses, connections - - check* Frame Brake operation - - check* Brake pad wear - - check* Brake fluid level - - check* Brake fluid - - change* Brake master cylinder cup and dust seal - -...
  • Page 9: Engine Parts Installation

    Engine Parts Installation Air Intake Parts Remove the air cleaner element or cut the cleaner element off remaining the wire net to reduce the air flow resistance. When removing the air cleaner element, remove the element and relational parts as ○...
  • Page 10: Camshaft Chain Tensioner

    Camshaft Chain Tensioner Replace the cam chain tensioner with the kit to decrease the flutter of tensioner. Apply the engine oil to the tensioner rod, O-ring and tensioner body, insert them into the tensioner body. Check to see that the tensioner rod turns freely in the body, if not, polish the tensioner ○...
  • Page 11: Camshafts, Sprockets

    Ninja ZX-10R Service Manual. If you adjust the valve timing, install the sprocket to the camshaft between the adjustable range of the long bolt holes.
  • Page 12 Method of measuring clearance of valve and piston –2. Adjust the valve clearance and valve timing. ○ Remove the cylinder head, and put a small piece of modeling clay on the hollow of piston ○ to prevent valve from coming in contact. Install the cylinder head and adjust the camshaft chain timing.
  • Page 13: Cylinder Head

    Cylinder Head Before reassemble the cylinder head grind off the stepped portions of the port and smooth the inside of ports to make intake/exhaust gas flow smooth. Grind off the stepped portions only at the mating surface between the carburetor holder ○...
  • Page 14: Cylinder Compression

    The combustion chambers are modified by cutting work but the edges shown must be hand finished for smooth corners. ○ When grinding the cylinder head surface or using thinner gasket, adjust the valve timing to keep that the valve to piston clearance is not less than the minimum value (IN: 0.7 mm, EX: 1.2 mm).
  • Page 15: Pistons

    Pistons Kit Piston: SB (1) 13001-0077 Kit pistons are exclusive the two piston rings for reduce the compression height (between the center of piston pin hole and the shoulder of the piston) and the mechanical friction loss. Kit piston has more reduced the weight compared the original piston. To adjust the cylinder compression to 14.3, use the kit pistons and grind off the cylinder head under surface to 0.4 mm.
  • Page 16 (2) 13001-0078 Kit pistons are exclusive the two piston rings for reduce the compression height (dimension between the center of piston pin hole to shoulder of the piston) and the mechanical friction loss. Kit piston has more reduced the weight compared the original piston. To adjust the cylinder compression to 14.5, use the kit pistons and remodel the original cylinder head.
  • Page 17: Crankshaft Main Journal Bushings

    Note: Use the kit pistons (13001-0077, -0078) following below. Use the kit connecting rod assemblies (13251-0015). ○ Use the kit piston rings (13008-0019). ○ There are the machining edges for the valve relief portions of the piston heads. Must be ○...
  • Page 18 Crankshaft Main Journal Diameter Marks None: 34.984~34.992 mm “1” Mark: 34.993~35.000 mm None [C] 1: [D] Crankcase Main Bearing Inside Diameter Marks 38.000~38.008 mm ○: None: 38.009~38.016 mm Mark portion: # 1~5 Crankshaft Main Journal Bushings Kit Bushing Kit Bushing Color #1.5 Blue...
  • Page 19: Connecting Rod Bolts

    Crankshaft Main Journal Bushing Selection Crankshaft Crankcase Crankshaft Main Journal Bushing Clearance (recommend) ○ Make the clearances between the crankshaft main journals within the prescribed allowances. Excessive clearances will cause the oil pressure at the crankshaft main journals to drop and lead to the damage of the bearing. Connecting Rod Bolts 1.
  • Page 20 2. Kit Connecting Rod Connecting Rod Bolt Use the kit connecting rod bolts (with the original connecting rod bolts) and nuts. The kit connecting rod can use the original connecting rod bolt (92153-0491). When using the original connecting rod bolts, make recesses at both ends of the original connecting rod bolt to measure its length and determine the bolt stretch.
  • Page 21: Connecting Rod Big End Bushings

    Connecting Rod Big End Bushings The connecting rod bushing in the kit has improved its anti-seizure feature than standard one. Connecting Rod Big End Bushing/Crankpin Clearance ※When adjust the clearance by measurement in case aiming the clearance 0.050 mm. Crankpin Diameter Marks ○: 34.493~34.500 mm None: 34.484~34.492 mm Connecting Rod Big End Bore Diameter Marks...
  • Page 22: Clutch Adjustment (back-torque Limiter Setting)

    Clutch Adjustment (Back-Torque Limiter Setting) The Ninja ZX-10R engine is equipped with the Kawasaki back-torque limiter mechanism in the clutch. The back-torque limiter works to reduce the chance of rear wheel hop caused by engine braking during hard braking and down shifting. The back-torque limiter operating condition can be changed by changing the total thickness of clutch plates and changing the number of leaf springs.
  • Page 23 When decreasing the length [A], total thickness of clutch plates, use the kit spring retainers (provided as optional production parts) to keep the preload of clutch springs according to the table below. Length [A] 53.0 ~ 53.5 mm 52.5 ~ 52.9 mm 51.9 ~ 52.4 mm ※...
  • Page 24 [A] Spacers [B] Needle Bearing [C] Bushing [D] Clutch Housing [E] Clutch Hub [F] Sub Clutch Hub Friction Plates (48 Slots) Steel Plates (t 2.6 mm) Washer Spring Friction Plates (36 Slots) Steel Plates (t 2.9 mm) Spring Plate Spring Retainer...
  • Page 25 • Engage the cam followers (Clutch Hub) with the cams (Sub Clutch Hub). • To measure the effective stroke of clutch spring plate, set a dial gauge [A] against the raised center [B] of the clutch spring plate. • Move the clutch housing gear back and forth [C]. The difference between the highest and lowest gauge readings is the amount of the effective stroke of clutch spring plate.
  • Page 26 Spring Plate Assembly The spring plate assembly are available for increase the spring constant. When outbreak the starting judder, use the spring plate assembly of the kit parts. Whenever the plate thickness is difference for adjusting the clutch plate, take care the length [A]. Part Number Spring Constant 2004 ~ 2005 ZX-10R (Standard)
  • Page 27 [A] Spacers [B] Needle Bearing [C] Bushing [D] Clutch Housing [E] Clutch Hub [F] Sub Clutch Hub Friction Plates Spring Plate Assembly Steel Plates Spring Plate Spring Retainer...
  • Page 28: Transmission

    Transmission Type B ~ D of the kit gears are available of the 2006 model ZX-10R. To change the gear ratios with combination the gears. Remove the three steel balls (600A0500) from the output shaft assembly. This is done to start easily the engine with the second gear.
  • Page 29 Use the type B ~ D input shafts with the shim adjustment since their sizes are, different from the standard shaft, designed taking the shim adjustment into account in order to make the dog lengths of the 3 – 5 &...
  • Page 30: Alternator

    Alternator Racing kit of the 2006 model ZX-10R are available the alternator. To quicken response by reducing the flywheel mass and to reduce the weight, use the kit alternator. Also use the kit alternator improve the engine ability Kit Alternator Rated Output 10 A @ 8 000 rpm (original: 30 A @ 5 000 rpm) ※...
  • Page 31 Installation Stator The stator is fixed to the cover (14031-0063) by the bolts. Run the alternator lead from the inside of the cover as shown in the illustration. A. Fix the stator to the cover by the bolts. Regulator Installation Use the kit alternator and the kit regulator (21066-0010) as a set.
  • Page 32 2. In case of without Starter Motor ※ Refer to the illustration of 1. Kit Alternator Installation. Remove the related parts of the starter motor and insert the plugs to the hole of the starter motor inserted as shown in the illustration. 1.
  • Page 33 Part Name Part No. Plug 92066-1332 Plug 92066-1333 O-ring 92055-1262 Bolt 130G0625 312B0600 Calk the bolt for unplug the plug. Insert the plug into the hole of the starter motor and tighten the nut. Apply liquid gasket. Replace the pulsing rotor with the kit rotor (21007-0085).
  • Page 34: Water Temperature Sensor

    Water Temperature Sensor The original water temperature sensor installed in the cylinder head must be remain and connected to the main harness because the electronic control unit (E.C.U.) needs the output signal from the original water temperature sensor. Radiator (Kit) 2006 model ZX-10R racing kit provides the sub radiator (39060-0030) to improved the cooling function.
  • Page 35 Connect the main radiator and sub radiator with the brackets (11054-0459). Fix the brackets (11054-0459) on the sub radiator by the bolts (130L0612). ○ Fix a wire netting in front of sub radiator for prevent the fin damages due to the stepping stone.
  • Page 36 Water Pipe Installation Use the main radiator only. Divide the original water hose (39062-0109) between the cylinder head and the radiator and insert the water pipe (39192-0011). Install the kit water temperature sensor (for water temperature gauge of kit meter, 21176-1099) to the kit water pipe.
  • Page 37 Use the kit sub radiator with the main radiator. Water Inlet of Radiator Body Divide the original water hose (39062-0109) between the cylinder head and the radiator and insert the water pipe (39192-0039). Install the kit water temperature sensor (for water temperature gauge of kit meter, 21176-1099) to the kit water pipe.
  • Page 38: Oil Catch Tank (kit)

    Oil Catch Tank (Kit) Use the oil catch tank for the engine blowby gas. Oil Catch Tank: 52001-0002 Tank Capacity: Approximately 570 cc Oil Catch Tank Installation Install the mounting bracket (11054-0455) with regulator under the cross pipe of the frame by the bolts (use the original regulator mounting bolts).
  • Page 40: Cover Gaskets (kit)

    Oil Pan: Alternator Cover: ECU (Kit) The 2006 model ZX-10R kit ECU has following functions. Refer to the Kawasaki FI Calibration Tool Instruction manual for the ECU function set up method. 1. Auto Shift Functions Be sure use the point type sensor.
  • Page 41: Frame Parts Installation

    Frame Parts Installation Throttle Parts (Kit Parts) The following throttle cases, grip and reels are available as kit parts. These kit parts quicken throttle response to the twist grip. 1) Throttle Case Parts Throttle Case, Upper Throttle Case, Lower Bolts (2) Grip, Right 2) Throttle Reels Tow types are available.
  • Page 42: Final Drive Parts (kit Parts)

    Final Drive Parts (Kit Parts) 1) Drive Chain #520 Joint endless drive chain is available as an kit parts. 2) Chain Guard 1. Guard: 55020-0236 2. Bolt: 130J1020 3. Swingarm (Left Side) Brake Pads (Kit Parts) The front and rear brake pads for racing use are available. The front pads are for higher braking force, and the rear pads are for higher braking force.
  • Page 43: Seat Height Adjustment

    Seat Height Adjustment Loosen the nut (1) and insert the spacer (2) as required. Tighten the nut (1) to 59 N·m (6.0 kgf·m, 43 ft·lb) of torque. When changing the seat height, adjust the spring preload of the rear shock absorber. As the rear suspension tends to be softer when raising the seat height with the adjusting ○...
  • Page 44 Seat Height Adjustment...
  • Page 45: Front Fork Springs (kit Parts)

    Front Fork Springs (Kit Parts) The kit front fork springs are available for racing. 1) Front Fork Specifications Items Rebounded damping setting (Upper) Compression damping setting (Lower) Fork oil Fork oil level Oil lock Oil seal Spring length Spring constant Spacer length Sub spring stroke 2) Front Fork Spring...
  • Page 46 Fork Spring Installation...
  • Page 47: Electrical System

    Electrical System Battery Use the original battery with 12 V 10 Ah or more capacity. Main Harness and Sub Harness (Kit Part) Main harness and sub harness are available for racing use as kit parts. Select one of them in accordance with your race regulation. Main Harness (with Original Meter and Kit Meter): 26031-0328 Sub Harness (with Original Meter): 26031-0425 Sub Harness (with Kit Meter): 26031-0426...
  • Page 48 Main Harness Combination Parts Table Use the kit main harness or sub harness with the following parts as a set. Parts Meter Assembly (Original) Tachometer with Water temperature Gauge (Kit) Water Temperature Gauge Lead (Kit) Water temperature sensor (Kit) Relay Box (Kit) ○...
  • Page 49 When using the kit main harness (Original meter: 26031-0426), the following original parts are not required. Original Main Harness Ignition Switch Rear Brake Light Switch Side Stand Switch Relay Box Turn Signal Relay Head Light, Tail/ Brake Light License Plate Light Front Right Turn Signal Light Front Left Turn Signal Light Rear Right Turn Signal Light...
  • Page 50 Kit Main Harness Installation...
  • Page 51 When using the recommended auto shifter to connect the [11] auto shifter connector. ○ When using the kit tachometer, always connect the water temperature sensor connector at the cylinder head rear side. ○ For recommended auto shifter, refer to the Kawasaki FI Calibration Tool Instruction Manual of another sheet. NOTE...
  • Page 52 1. To connect the Fuel Pump. 2. To connect the E.C.U (Black). 3. To connect the atmospheric pressure sensor (Black). 4. To connect the inter face box (Black). 5. To connect the vehicle down sensor (Gray). 6. Relay Box (27002-1062) 7.
  • Page 53 Sub Harness (Original Meter) Installation 1. To connect the original meter (Black). 2. To connect the right switch housing (Black). 3. To connect the left switch housing (Black). 4. Semitransparent connector (not use) 5. To connect the shift up indicator (Green). Install the harness (26031-0426) for the original meter as shown in the illustration.
  • Page 54 Sub Harness (Kit Meter) Installation 1. Shift up Indicator Lamp (23016-0006) 2. To connect the shift up indicator lamp (Green). 3. Tachometer with Water Temperature Gauge (25031-1142) 4. To connect the tachometer with water temperature gauge (Black). 5. To connect the right switch housing (Black). 6.
  • Page 55 Kit Sub Harness (26031-0427) Installation Install the kit sub harness (26031-0244) as shown in the illustration. 1. E.C.U. 2. Sub Harness (26031-0427) 3. To connect the auto-shifter (Blue). 4. To connect the speed limit switch (Black). 5. To connect the inter face box (Black). Connect the [3] auto shifter and the [4] speed limit switch, extending the lead as required.
  • Page 56: Wiring Diagram (with Original Meter)

    Wiring Diagram (with Original Meter)
  • Page 58: Wiring Diagram (with Kit Meter)

    Wiring Diagram (with Kit Meter)
  • Page 61 Racing Kit Parts List...
  • Page 62 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Valve(s) Ref. Part No. Description 49078 49078-0049 SPRING-ENGINE VALVE,EXHAUST (OPTION) DEC.21,2005 Quantity-ZX1000 Spec Code ’06 DR6F...
  • Page 63 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Camshaft(s)/Tensioner Ref. Part No. Description 12048 12048-0028 TENSIONER-ASSY (OPTION) 13116 13116-1166 ROD-PUSH (OPTION) 49118 49118-0034 CAMSHAFT-COMP,INTAKE (OPTION) 49118A 49118-0077 CAMSHAFT-COMP,EXHAUST (OPTION) 49118B 49118-0078 CAMSHAFT-COMP,INTAKE (OPTION) 92015 92015-1078 NUT,FLANGED,6MM (OPTION) 92055 92055-0053 RING-O,20.8X1.9...
  • Page 64 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Crankshaft/Piston(s) Ref. Part No. Description 13001 13001-0077 PISTON-ENGINE,SB (OPTION) 13001A 13001-0078 PISTON-ENGINE (OPTION) 13002 13002-0013 PIN-PISTON (OPTION) 13008 13008-0019 RING-SET-PISTON (OPTION) 13251 13251-0015 ROD-ASSY-CONNECTING,L=110.45 (OPTION) 92015 92015-1311 NUT,FLANGED,8MM (OPTION) 92033 92033-1161 RING-SNAP,PISTON PIN...
  • Page 65 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Clutch Ref. Part No. Description 13089 13089-0011 PLATE-CLUTCH,STD +40% (OPTION) 13089A 13089-0012 PLATE-CLUTCH,STD +60% (OPTION) DEC.21,2005 Quantity-ZX1000 Spec Code ’06 DR6F...
  • Page 66 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Transmission(1/2)(TYPE-B) Ref. Part No. Description 13127 13127-0041 SHAFT-TRANSMISSION INPUT,13T (OPTION) 13144 13144-0021 SPROCKET-OUTPUT,16T,#520 (OPTION) 13144A 13144-0022 SPROCKET-OUTPUT,17T,#520 (OPTION) 13262 13262-0152 GEAR,OUTPUT 2ND,39T (OPTION) 13262A 13262-0185 GEAR,INPUT 2ND,19T (OPTION) 13262B 13262-0264 GEAR,INPUT 3RD&4TH,19T&20T (OPTION) 13262C 13262-0265...
  • Page 67 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Transmission(2/2)(TYPE-B) Ref. Part No. Description 92200E 92200-0230 WASHER,28.3X34.0X1.4 (OPTION) 92200F 92200-0231 WASHER,28.3X34.0X1.8 (OPTION) 92200G 92200-0232 WASHER,28.3X34.0X2.0 (OPTION) DEC.21,2005 Quantity-ZX1000 Spec Code ’06 DR6F...
  • Page 68 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Transmission(1/2)(TYPE-C) Ref. Part No. Description 13127 13127-0042 SHAFT-TRANSMISSION INPUT,14T (OPTION) 13144 13144-0021 SPROCKET-OUTPUT,16T,#520 (OPTION) 13144A 13144-0022 SPROCKET-OUTPUT,17T,#520 (OPTION) 13262 13262-0152 GEAR,OUTPUT 2ND,39T (OPTION) 13262A 13262-0166 GEAR,OUTPUT 4TH,32T (OPTION) 13262B 13262-0185 GEAR,INPUT 2ND,19T (OPTION) 13262C 13262-0272...
  • Page 69 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: B-10 Transmission(2/2)(TYPE-C) Ref. Part No. Description 92200E 92200-0230 WASHER,28.3X34.0X1.4 (OPTION) 92200F 92200-0231 WASHER,28.3X34.0X1.8 (OPTION) 92200G 92200-0232 WASHER,28.3X34.0X2.0 (OPTION) DEC.21,2005 Quantity-ZX1000 Spec Code ’06 DR6F...
  • Page 70 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: B-11 Transmission(1/2)(TYPE-D) Ref. Part No. Description 13127 13127-0043 SHAFT-TRANSMISSION INPUT,16T (OPTION) 13144 13144-0021 SPROCKET-OUTPUT,16T,#520 (OPTION) 13144A 13144-0022 SPROCKET-OUTPUT,17T,#520 (OPTION) 13262 13262-0279 GEAR,INPUT 2ND,18T (OPTION) 13262A 13262-0280 GEAR,INPUT 6TH,22T (OPTION) 13262B 13262-0281 GEAR,OUTPUT LOW,37T (OPTION)
  • Page 71 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: B-12 Transmission(2/2)(TYPE-D) Ref. Part No. Description 92200E 92200-0230 WASHER,28.3X34.0X1.4 (OPTION) 92200F 92200-0231 WASHER,28.3X34.0X1.8 (OPTION) 92200G 92200-0232 WASHER,28.3X34.0X2.0 (OPTION) DEC.21,2005 Quantity-ZX1000 Spec Code ’06 DR6F...
  • Page 72 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: B-13 Gear Change Drum/Shift Fork(s) Ref. Part No. Description 13145 13145-0021 CAM-CHANGE DRUM (OPTION) DEC.21,2005 Quantity-ZX1000 Spec Code ’06 DR6F...
  • Page 73 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: B-14 Gear Change Mechanism Ref. Part No. Description 13161 13161-0042 LEVER-COMP-CHANGE SHAFT (OPTION) 92026 92026-1534 SPACER,14X20X1.0 (OPTION) 92144 92144-1029 SPRING (OPTION) 92145 92145-0287 SPRING (OPTION) 480J1400 CIRCLIP-TYPE-C,14MM (OPTION) DEC.21,2005 Quantity-ZX1000 Spec Code ’06...
  • Page 74 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Engine Cover(s) Ref. Part No. Description 11004 11004-0022 GASKET-HEAD,T=0.55 (OPTION) 11004A 11004-0023 GASKET-HEAD,T=0.45 (OPTION) 11004B 11004-0026 GASKET-HEAD,T=0.65 (OPTION) 11004C 11004-0034 GASKET-HEAD,T=0.50 (OPTION) 11004D 11004-0052 GASKET-HEAD,T=0.60 (OPTION) 11061 11061-0229 GASKET,IDLE GEAR COVER (OPTION) 11061A 11061-0230 GASKET,STARTER COVER...
  • Page 75 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Fuel Injection Ref. Part No. Description 21175 21175-0096 CONTROL UNIT-ELECTRONIC (OPTION) 21176 21176-1099 SENSOR,TEMP (OPTION) 26011 26011-0071 WIRE-LEAD,TEMP SENSOR EARTH (OPTION) 26011A 26011-1779 WIRE-LEAD,METER-TEMP SENSOR (OPTION) 26031 26031-0240 HARNESS,INTERFACE BOX (OPTION) 26031A 26031-0425 HARNESS,KIT METER...
  • Page 76: Oil Pump

    This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Oil Pump Ref. Part No. Description 13107 13107-0127 SHAFT (OPTION) 16142 16142-0036 COVER-PUMP (OPTION) 16154 16154-0060 ROTOR-PUMP (OPTION) DEC.21,2005 Quantity-ZX1000 Spec Code ’06 DR6F...
  • Page 77 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Generator Ref. Part No. Description 11054 11054-0455 BRACKET,OIL TANK 21001 21001-0042 GENERATOR (OPTION) 21007 21007-0085 ROTOR (OPTION) 21066 21066-0010 REGULATOR-VOLTAGE (OPTION) 26031 26031-0323 HARNESS (OPTION) 52001 52001-0002 TANK-OIL 92022 92022-304 WASHER,6.2X11X1 92143...
  • Page 78 This catalog covers: ’06 ZX1000DR6F Engine GRID NO. This grid covers: Radiator Ref. Part No. Description 11054 11054-0459 BRACKET (OPTION) 35063 35063-0316 STAY,MAIN (OPTION) 35063A 35063-0317 STAY,RH,SUB RAD (OPTION) 35063B 35063-0318 STAY,LH,SUB RAD (OPTION) 39060 39060-0030 RADIATOR,SUB (OPTION) 39062 39062-1072 HOSE-COOLING (OPTION) 39192...
  • Page 79 This catalog covers: ’06 ZX1000DR6F Chassis GRID NO. This grid covers: Rear Hub Ref. Part No. Description 43082 43082-0005 PAD-ASSY-BRAKE,FR,F9633 (OPTION) 43082A 43082-1192 PAD-ASSY-BRAKE,RR,C93 (OPTION) 43082B 43082-1220 PAD-ASSY-BRAKE,RR,C93G (OPTION) 44026 44026-0091 SPRING-FRONT FORK,K=9.5N/MM (OPTION) 44026A 44026-0092 SPRING-FRONT FORK,K=10.0N/MM (OPTION) 44026B 44026-0093 SPRING-FRONT FORK,K=10.5N/MM (OPTION) 55020...
  • Page 80 This catalog covers: ’06 ZX1000DR6F Chassis GRID NO. This grid covers: Handlebar Ref. Part No. Description 27010 27010-0040 SWITCH,SPEED CONTROL (OPTION) 31064 31064-1151 PIPE-COMP,GRIP (OPTION) 32099 32099-0004 CASE,UPP (OPTION) 32099A 32099-0005 CASE,LWR (OPTION) 46075 46075-1143 GRIP,THROTTLE (OPTION) 46091 46091-1809 HOUSING-ASSY-CONTROL,RH (OPTION) 54012 54012-0185...
  • Page 81 This catalog covers: ’06 ZX1000DR6F Chassis GRID NO. This grid covers: Meter(s) Ref. Part No. Description 11053 11053-1673 BRACKET,KIT METER (OPTION) 11054 11054-0423 BRACKET,COWLING STAY,LH (OPTION) 11054A 11054-0424 BRACKET,COWLING STAY,RH (OPTION) 13061 13061-0124 BOSS (OPTION) 23016 23016-0006 LAMP-ASSY,INDICATOR (OPTION) 25031 25031-1142 METER-ASSY (OPTION)
  • Page 82 Doc No. 99929-0011-01...

This manual also for:

2006 ninja zx-10r

Comments to this Manuals

Symbols: 0
Latest comments:
  • henry mendoza Mar 07, 2016 06:00:
    how to open the pasNanger set.
  • jeffrey l Nash Sep 14, 2014 07:05:
    Need a picture of a clutch basket filled with steel plates and friction plates in a 2015 kawasakizx​10r