Subscribe to Our Youtube Channel
Related Manuals for Arctiko ULUF
Summary of Contents for Arctiko ULUF
- Page 1 ORIGINAL OPERATING INSTRUCTIONS ULUF models Ultra low temperature freezers -90°C Ultra low temperature freezers -86°C Low temperature freezers -40°C...
-
Page 2: Table Of Contents
Contents Contents Page Page Low temp. alarm Introduction Probe failure Further information about the appliance Power failure Symbols Description of compressor failure alarm Abbreviations Logging interval Alarm setting instructions Safety Select language Intended use Light Personal safety Probe at main screen Advanced settings Handling &... -
Page 3: Introduction
Introduction Safety Arctiko is obligated as a supplier to ensure the users safety when operating Please take a few minutes to read and become familiar with the advantages of your appliance. To meet the high quality demands required by the medical one of our appliances. -
Page 4: Handling & Transportation
Directive, WASTE ELECTRICAL AND ELECTRONIC EQIUPMENT (WEEE). occurred during shipping. If damage is observed, report to the shipping company and your local Arctiko distributor. 2. Remove all packaging materials, plastic and straps. All packing material is Disconnect power supply before operation. -
Page 5: Installation
Installation Location Place the appliance in a location that satisfies the following conditions in or- der to achieve optimal operating results: Preparing the appliance - Firm and levelled floor: - Placing the appliance on a firm and flat floor reduces the risk of excessive noise and vibration. - Unpack the appliance: - Remove all packaging materials, plastic bags and straps. -
Page 6: Electrical Connection
This is normal as the chamber temperature may be outside the UNIT AMPS (A) alarm limits during the temperature pull down. You can safely mute or ULUF 15 cancel the alarm (see section “How to mute and accept alarms”). ULUF 65 ULUF 125 ULUF 450 3. -
Page 7: Product Description
Cabinet description Product description 20. Main control unit The ULUF range offers the best ultra low and low temperature freezing with high performance and stability. Standard features is filter-less construction for 19. Power supply less maintenance, low noise level, low energy consumption, low heat 21. -
Page 8: Cabinet Description
Cabinet description Probes and portholes As standard, the appliance is equipped with a temperature probe inside the appliance. The probe monitors the temperature in the chamber and controls the operation of the compressor. 1. Top panel 12. Inner doors Compressor Foam Insolated. -
Page 9: Vacuum Valve
Remote alarm contact The Main control unit is located in the compressor compartment behind the top panel. The display is mounted in the top-panel. The remote alarm contact is located in the compressor compartment. 1. ON/OFF 7. Ambient temperature 13. Alarm indicator 2. -
Page 10: Cooling System
ULUF 15 it is placed on the right side. into levels inside the cabinet ensuring a uniformity of only ± 2°C. -
Page 11: Controller Operation/Settings
Controller operation/settings How to change the setpoint Main menu Press “ENTER” to access main menu Press “ENTER” to access Press “ENTER” to enter the ‘Custom settings’ password Press “ENTER” to access ‘Setpoints’ The password is “0000” - Press to increase or Press “ENTER”... -
Page 12: High Temp. Alarm
Attention! Attention! The factory setting for door alarm activation is 5 minutes. To change this setting, contact When changing the high temperature setting, remember to have the setpoint of the the distributor/seller of the appliance. The user can only enable/disable this function. appliance in mind. -
Page 13: Probe Failure
The Power failure icon will remain in the display until the alarm is accepted. Attention! The factory log setting is one minute. To provide the best service and support Arctiko STRONGLY recommends keeping this setting. When logging every minute, the capacity of the memory is more than 20 years. -
Page 14: Alarm Setting Instructions
Alarm setting instructions Select language The default language of the controller is English. The language can be changed in the “Select language” menu. The available languages are English, German, Russian, French, Spanish, Swedish, Turkish and Polish. Changing the language will change the text throughout the controller and can be done at any time without interrupting the operation of the appliance. -
Page 15: Probe At Main Screen
Automatic defrost Press “ENTER” to access menu Press “ENTER” to access Press “ENTER” to type password custom settings Automatic defrost is NOT possible on the ULUF range. – Please see Maintenance /defrosting. Manual defrost - Press until the “Probe The manual defrost function of the G214 controller is NOT possible to be The password is “0000”... - Page 16 Hysteresis Service The hysteresis in combination with the setpoint defines the temperatures for The service menu offers information on compressor and fan activation time, starting and stopping the cooling compressor in the appliance. E.g. with a probe temperatures and firmware versions of controller. There are no setpoint of -80°C and a hysteresis of 2, the compressor will start when the changeable settings in the service menu.
-
Page 17: Advanced Setting Instructions
Press “ENTER” to access Press “ENTER” to access Press “ENTER” to access Press “ENTER” to access Press “ENTER” to access Press “ENTER” to access available for the ULUF range available for the ULUF range “Calibration” “Hysteresis” “Temp. range limits” “Service”... -
Page 18: Advanced Service Settings
If you forgot the password for the appliance, it is possible to reset to the factory setting “0000”. In order to reset the password, you need to require a “reset password” from your Arctiko distributor. - Contact your distributor for the code needed. -
Page 19: Data Log
Attention! Do not remove the USB drive while transferring data. Wait for the “Transfer completed” message to show before removing the drive. - Use to hightlight - Use until highlight the - Enter NEW password again The password has been reset Open and process data on a computer the numbers numbers... - Page 20 3. Select “ALL Files (*.*)” to make sure the relevant files are visable. 4. The files should now be visable. “data00.txt” and “param00.txt”. If more than one readout has been preformed, each readout will create a set of files 5. When the desired file is opened, the following window will appear. with the number increased by one.
-
Page 21: Description Of Data Points
Temperature of compressor 2 (if present) Room temp Ambient temperature Evaporator temp Temperature of evaporator (Not applicable for ULUF-models. ) Events Door open “0” – door closed / “1” – door open Door opening time Duration opening duretion in seconds... -
Page 22: Default Settings
Default settings ULUF 60/120/400/400-D/500/500-D/700/700-D/800/800-D: Default settings ULUF 15/65/125: Description Arctiko default Customer Description Arctiko default Customer settings settings settings settings Custom Settings (Password) 0000 Custom Settings (Password) 0000 Set point Set point -40,0 Freezer -80,0 Freezer Alarm Settings: Alarm Settings:... - Page 23 Default settings ULUF 450/450-2M/550/550-2M/750/750-2M/850/850-2M: Default settings ULUF 490/490-2M/590/590-2M/890/890-2M: Description Arctiko default Customer Description Arctiko default Customer settings settings settings settings Custom Settings (Password) 0000 Custom Settings (Password) 0000 Set point Set point -80,0 Freezer Freezer -80,0 Alarm Settings: Alarm Settings:...
-
Page 24: Alarms
See “Controller operation /Alarm settings” for a detailed description of each Frequent and correctly executed maintenance is essential to ensure high alarm. performance and functionality of the appliance. Arctiko recommends a thorough examination twice a year and cleaning at least once a month. How to mute and accept alarms Never disassemble, repair, or modify the appliance yourself. -
Page 25: Cleaning
Defrosting Arctiko strives for day-to-day delivery of spare parts. However, some special This appliance does not offer automatic defrosting as such function would parts may take longer due to production time. Arctiko guarantees availability increase the chamber temperature (and stored samples) to a value that could of spare parts for all appliances for at least 10 years after the delivery. -
Page 26: Troubleshooting
Notes: Troubleshooting Most malfunctions arise in wrong use of the appliance and can often be solved on the spot. In order to resolve some of the most common malfunc- tions, please see the following troubleshooting scheme: Problem Cause Action Overload or load of warm products Discharge warm or excess may cause the temperature to rise. - Page 27 5080038-11-GB...
Need help?
Do you have a question about the ULUF and is the answer not in the manual?
Questions and answers