Black & Decker BL188 Original Instructions Manual page 9

LED work light
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (8)will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Bit tip storage
A bit storage slot (9) is built into the base of the tool.
Troubleshooting
Problem Possible cause
Unit will not start. Battery pack not
installed properly.
Battery pack not
charged.
Unit starts immedi- The switch has
ately upon inserting been left in the "on"
battery position.
Battery pack will not Battery pack not
charge. inserted into charger.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off Battery pack has
abruptly. reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior.
Protecting the environment
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Possible solution
Check battery pack
installation.
Check battery pack charg-
ing requirements
The switch must be
moved to "off" to prevent
the tool from immediately
starting when battery is
inserted.
Insert battery pack into
charger until LED lights.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Allow battery pack to cool
down.
Place on charger
and allow to charge.
(Original instructions)
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Voltage
V
DC
No-load speed Min
Max. torque Nm
Chuck capacity mm
Max Drilling capacity
Steel/wood mm
Weight kg
Charger
Input voltage V
AC
Output voltage
V
DC
Current mA
Approx. charge time
Hrs
Battery BL1518
Voltage V 18
DC
Capacity Ah 1.5
Type Li-Ion
Level of sound pressure according to EN 62841:
Sound pressure (L ) 87.5 dB(A), uncertainty (K) 5 dB(A)
pA
Sound power (L ) 98.5 dB(A), uncertainty (K) 5 dB(A)
WA
Vibration total values (triax vector sum) according to EN 62841:
2
Drilling into metal (a ) 1.9 m/s , uncertainty (K) 1.5 m/s
h.D
Impact drilling into concrete (a ) 10.4 m/s
h.ID
ENGLISH
BL188 H2
0-450 / 0-1800
-1
1.08 (1.46 with
battery)
90590289 90634972
100- 240 220 - 240
8 - 20 8 - 20
400 1000
3 - 5 1.5 - 2
BL2018 BL4018
18 18
2.0 4.0
Li-Ion Li-Ion
2
2 2
, uncertainty (K) 1.5 m/s
18V
52
13
13/35
9