Quick Change Gears - Grizzly G0554Z Owner's Manual

14" x 40" gear-head floor lathe
Table of Contents

Advertisement

Quick change Gears

the quick change gears are used with the feed
rate controls to set the required feed rate.
Serious personal injury
can result if you make
contact with the gears,
pulleys, and belt inside
the left door of the lathe
when the machine is run-
ning or starts unexpect-
edly.
nect the lathe from power
before opening the left
side door.
the Model g0554z lathe ships with the 25t
installed in the top position, the 120t/127t in the
middle position, and the 50t installed in the bot-
tom position, as shown in Figure 60. this configu-
ration of gears will cover most feed rates and inch
threading. the 30t, 32t, and two 40t gears are
provided for additional feed rates and inch/metric
threading.
pivot
hex nut
Side
Front
View
View
Top
Middle
120
Bottom
127
Figure 60. Quick change gears.
-44-
ALWAyS
discon-
top
Middle
TPI
Bottom
1 2 3 4 5 6 7 8
in
25
127
C
4 4
120
A
.0294
D
50
.0103
C
8
A
.0147
D
.0051
C
16 18 20 22 23 24 26 28
B
25
.0073
D
127
.0025
120
E
32 36 40 44 46 48 52 56
A
50
.0042
F
.0014
Tools Needed
hex Wrench 5mm .............................................. 1
Wrench or socket 16mm ................................... 1
Wrench or socket 18mm ................................... 1
To configure the quick change gears:
1.
disConnECt lAthE FroM poWEr!
2.
Engage the feed gears so that the change
gears will not rotate in the following steps,
then open the left side door.
3.
loosen the pivot hex nut and move the
middle gears away from the bottom gear,
then re-tighten the hex nut to keep the pivot
assembly in place.
4.
loosen the hex nut that secures the middle
gears and lower them away from the top
gear.
5.
to change either the top or bottom gears:
a. remove the cap screw and flat washer
that secures the gear, then the gear.
Note: Take care not to misplace the key
from the gear shaft.
b. Clean away debris and grime from the
gear and apply a light coat of machine oil
to protect it from rust before you store it.
c. repeat Step b for the replacement gear,
then align it with the key and insert it on
the gear shaft.
Note: When cutting metric threads, the
bottom gear must mesh with the 120T
gear of the middle gears. In order to do
this, you need to install the bottom gear
with the raised hub facing in toward the
lathe.
d. re-install the flat washer and cap screw.
5
5
5
6
6
1
1
3
2
2
4
.0261
.0235
.0214
.0205
.0196
.0181
Note: DO NOT overtighten the cap screw.
.0091
.0082
.0075
.0072
.0069
.0063
The cap screw merely holds the gear in
9 10 11 11
12 13 14
1
2
place and overtightening it will make it
.0131
.0117
.0107
.0102
.0098
.0090
harder to remove later and may restrict its
.0045
.0041
.0036
.0036
.0035
.0031
rotation.
.0065
.0058
.0053
.0051
.0049
.0045
.0023
.0020
.0019
.0018
.0017
.0015
.0038
.0034
.0031
.0030
.0028
.0026
.0013
.0011
.0010
.0009
.0009
.0008
7
1
2
.0168
.0059
.0084
.0030
.0042
.0015
Model g0554z (Mfg 01/09+)
.0024
.0008
Qty

Advertisement

Table of Contents
loading

Table of Contents