Related Manuals for HIRED-HAND Mega-Flow Butterfly
Summary of Contents for HIRED-HAND Mega-Flow Butterfly
- Page 1 Mega-Flow Butterfly Cone Fan Unassembled Owner’s Manual Hired-Hand, Mfg., Inc. PO Box 140 1733 County Road 68 Bremen, Alabama 35033 Part No. 4801-5327 Rev 6/07 Owners Manual Mega-Flow Butterfly Cone Fan - Unassembled...
-
Page 2: Warnings
The Hazards Involved Should Install, Adjust, And/Or Service This Equipment. Read And Understand This Manual In Its Entirety Before Proceeding. Failure To Observe This Precaution Could Result In Severe Bodily Injury Or Death! Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 2 of 12... -
Page 3: Limited Warranty
This warranty gives you specific legal rights and you may also have other rights that vary from area to area. Warrantor: Hired-Hand Mfg., Inc. PO Box 140 1751 County Road 68 Bremen, Alabama 35033 Phone 256-287-7000 Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 3 of 12... -
Page 4: Table Of Contents
2' (61 cm) scale or carpenter's square Needle nose pliers Electric or cordless drill 3/8" (10 mm) Socket -12pt. star Thread Locking Compound (LOCKTITE®) 3/8" (10 mm) Socket head bit Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 4 of 12... - Page 5 Sheave 10.4 Fenner (1011-5000) Bolt 3/8 x 16 x1 Shaft Coated (1002-2374) 1 x 7 5/8 (6403-2110) Bottom Vertical Mounting Bracket (0404-7587). Figure 2 – Internal Fan Assembly Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 5 of 12...
- Page 6 Internal Fan Assembly from Step 4 Bottom Panel (0404-7551) Straight Orifice (0404-8256) Figure 3 – Butterfly Fan Assembly Align Fan Blade with edge of orifice. Detail B Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 6 of 12...
- Page 7 Do Not Attempt To Lift Fan Without Sufficient Workers And Equipment. 15. Carefully lift fan into wall. 16. Securely attach fan to wall with screws (1004-1386). Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 7 of 12...
-
Page 8: Assemble Cone
Mounting holes for Install #14 x1/2" holes Damper Ring Arrange panels for assembly with pilot sm screw Inset C hole on each panel facing upward. Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 8 of 12... - Page 9 NOTE: Lower cone ring fits into outer hole. Figure 10 - Mount the Ring Assembly Figure 11 - Side View of Cone Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 9 of 12...
- Page 10 Cut hole for Cut hole for way up. motor motor Figure 14B Figure 14C Hole in Guard for 1.5Hp 1Ph Motor Hole in Guard for 1Hp 1Ph Motor Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 10 of 12...
- Page 11 (4501-2622) (4501-2957) OUTSIDE BOTTOM INSIDE INSIDE Figure 17 - Affix Labels 30. Connect power to fan and verify proper operation. 31. Fan and Cone installation complete. Part No. 4801-5327 Rev 6/07 Mega-Flow Butterfly Cone - Unassembled Page 11 of 12...
- Page 12 Mega-Flow Butterfly Cone Fan - Unassembled...
Need help?
Do you have a question about the Mega-Flow Butterfly and is the answer not in the manual?
Questions and answers