Table of Contents
Advertisement
Copy & Paste and Move & Paste
This section describes the Copy & Paste (or Move &
Paste) details.
<Precaution>
* The data copied (or moved) on the clipboard is
replaced with new data every time data is copied (or
moved).
* Note that the data copied in the clipboard is replaced
when pasting over the original data copied.
Executing Copy (or Move) and CLIP
1. Set the point to start COPY (or MOVE) and the point to
start the PASTE feature.
Set the COPY (or MOVE) starting point to the [CLIPBOARD
IN] key, the ending point to the [CLIPBOARD OUT] key, and
the PASTE starting point to the [AUTO PUNCH IN] key.
For more details on how to set (store) to the memory key
refer to page 34.
2. Press the [EDIT] key to proceed to the "Copy Clip?" (or
"Move Clip?") message.
To execute the Copy & Paste feature select "Copy Clip?".
Flashing
To execute the Move & Paste feature select "Move Clip?".
Flashing
3. Use the [CH STATUS/CH SEL] key to select the track to
COPY (or MOVE).
Both mono tracks and multiple tracks (including ALL tracks)
can be selected. During the Copy & Paste (or Move & Paste)
process it is only possible to change the paste destination
track of mono tracks or when copying (or moving) with
two tracks that are odd and even number tracks situated
next to each other. In any other case, when copying (or
moving) multiple tracks, the data is pasted to the original
copy site (or move) of the same track.
4. Press the [ENTER/YES] key.
Press the [ENTER/YES] key to complete the data copy (or
move) process. "Completed!" appears on the display then
the "Copy Paste" (or "Move Paste") message flashes.
This means that the sound data has been copied (or moved)
to the clipboard, and that the system is ready to proceed to
the following paste process.
The recorder is ready to paste if there is no problem with
the COPY/CLIP (or MOVE/CLIP) process. At this stage, it is
possible to check the sound data in which COPY/CLIP (or
MOVE/CLIP) was executed.
To check the data on the clipboard, refer to the instructions
described in "Checking Data in the Clipboard".
<Precaution>
• If COPY (or MOVE) is executed without selecting a track
to COPY (or MOVE), then " Select Track! " will appear
on the LCD with a flashing " Copy Clip! " (or " Move
Clip! ") message. In this case, repeat the procedure by
using the [CH STATUS/CH SEL] key to choose the track
to COPY (or MOVE).
• If the CLIPBOARD IN point and CLIPBOARD OUT point
is stored in the reverse time relationship when
attempting to COPY (or MOVE), then a " Void In Point! "
or " Void Out Point! " warning appears on the display
and prevents any further process. In such case, reset
the proper time relationship of the CLIPBOARD IN/
OUT points prior to COPY (or MOVE).
<Check the Clipboard Data>
Prior to pasting any sound data, follow the instructions
below to check for the presence of any sound data copied
(or moved) on the clipboard.
• Press the [PLAY] key while the [STOP] key is depressed.
The sound data copied or moved on the clipboard
appears (if the data is copied " Copy Clip Play!" appears,
and if it is moved data then " Move Clip Play!" appears),
and that data is played (clipboard play).
To monitor the sound played, make the adjustments
with the channel fader corresponding to the track
copied (or moved). The [CH STATUS/CH SEL] key
that was copied (or moved) flashes during playback.
The recorder automatically stop when clipboard play
is over.
• Press the [EDIT] key after checking the data.
When the earlier mentioned COPY (or MOVE) is
completed, the LCD will then return to the same
display (flashing " Copy Paste " or " Move Paste ").
Pasting Data
5. Press the [ENTER/YES] key when "Copy Paste" (or
"Move Paste") is flashing.
The menu to select the paste repeat frequency appears
("Repeat = 01"), then "01" and "Sure?" flashes. (Note that
"01" refers to paste once.) The [CH STATUS/CH SEL] key of
the track copied (or moved) flashes.
6. Use the [CH STATUS/CH SEL] key to select the paste
destination track.
• There is no need to select a track when pasting on the
same track.
• The mono track is the only track in which the paste
destination can be changed. The other condition in
which the paste destination can be changed is when the
data from two tracks (odd and even) next to each other
(1-2, 3-4, 5-6, 7-8, etc.) are copied (or moved) on the
clipboard. The paste destination track can be changed
by pressing the [CH STATUS/CH SEL] key in this case.
73
or
Advertisement
Chapters
Table of Contents
