Page 1
SEALED WELL STEAM TABLES INSTALLATION & OPERATING MANUAL...
Page 2
STEAM TABLE MANUAL Model: STESW- SEALED WELL STEAM TABLE INSTALLATION OPERATING MANUAL FOR YOUR SAFETY: Do not store or use flammable liquids and vapors in the vicinity of this or any other appliance. Warning: Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death.
STESW-4-240 Capped Nut 1/4-20 Capped Nut STESW-5-240 #10-32 x 3/8" Phillips Drive Machine Screw Screw *Note: STESW-2-120 has a qty of 8 acket PARTS INCLUDED Tools Required: Sockets or wrenches for Capped Nuts: 7/16" or 11mm Item Item # Item...
Page 4
STEAM TABLE MANUAL 1. Confirm all parts/hardware are included 2. A) Place the Body upside down on a clean surface to avoid scratching. Loosen the Screws on the inside and outside of the Body. Note: Do NOT fully remove Screws from the Body. B) Insert the Legs into the slots created by the outer shell of the Body and the brackets on the inside corners of the Body.
Page 5
STEAM TABLE MANUAL 4. A) Attach the Side Shelf Brackets using the Capped Nuts provided. The Left & Right Side Shelf Brackets have threaded studs which will point to the outside of the Steam Table when installed. Note: Do not fully tighten Capped Nuts. B) Install the Side Shelf on the Side Shelf Brackets. The Side Shelf will be positioned between the Body and the Side Shelf Brackets and the slots on the Side Shelf will go over the threaded studs on the Left &...
3000 12.5 STESW-4-240 4-Well 3000 NEMA 5-50 6-20 STESW-5-240 5-Well 3750 3750 15.6 NEMA 5-50 6-20 NEMA 5-20 : For STESW-2-120 NEMA L5-30 : For STESW-3-240 NEMA 6-20 NEMA 5-50 : For STESW-4-240 & STESW-5-240 NEMA 6-20 www.bk-resources.com | orders@bk-resources.com...
18 months from date of shipment from the factory. BK Resources will replace, without charge, any defective parts or component material, upon demonstration to its satisfaction that a breach of warranty did not exist.
Page 10
STEAM TABLE MANUAL Modelo: STESW- MESA DE VAPOR INSTALACIÓN Y MANUAL DE OPERACIÓN POR SU SEGURIDAD: No almacene o use líquidos y vapores inflamables alrededor de éste o cualquier otro aparato eléc- trico. Advertencia: La instalación incorrecta, ajuste, alteración, servicio o mantenimiento puede causar daño a la propiedad, lesión o muerte.
Page 11
Item Item # Capped Nut 1/4-20 Capped Nut #10-32 x 3/8" Phillips Drive Machine Screw Screw *Note: STESW-2-120 has a qty of 8 Tools Required: Sockets or wrenches for Capped Nuts: 7/16" or 11mm Phillips screwdriver acket cket STESW-2-120 -2-120...
Page 12
STEAM TABLE MANUAL 1. Confirmar que todas las partes/equipo están incluídos 2. A) Coloque la estructura boca abajo en una superficie limpia para evitar rayones. Afloje los tornillos en la parte interna y externa de la estructura. Nota: No remueva totalmente los tornillos de la estructura. B) Inserte las patas dentro de las ranuras creadas por la repisa externa de la estructura y los soportes en las esquinas internas de la estructura.
Page 13
STEAM TABLE MANUAL 4. A) Fije los soportes de la repisa lateral, utilizando las tuercas cubiertas que se incluyen. Los soportes de repisa izquierdos y derechos tienen pernos roscados que apuntarán hacia la parte externa de la Mesa de Vapor cuando esté instalada Nota: No apriete completamente las tuercas cubiertas. B) Instale la repisa lateral en los soportes laterales de la repisa.
Page 14
EXPLODED VIEW PARTS LIST Soporte de la tabla de cortar STESW-CBB STESW-CBB STESW-CBB STESW-CBB Description Item STESW-2-120 Item # STESW-3-240 Item # STESW-4-240 Item # STESW-5-240 Item # Tabala para cortar STESW-2-CB STESW-3-CB STESW-4-CB STESW-5-CB Cutting Board Bracket STESW-CBB STESW-CBB...
Page 16
NEMA 5-50 NEMA 5-50 6-20 6-20 5-Well 5-Well 3750 3750 NEMA 5-50 NEMA 5-50 STESW-5-240 STESW-5-240 15.6 NEMA 5-20 : For STESW-2-120 NEMA L5-30 : For STESW-3-240 NEMA 6-20 NEMA 5-50 : For STESW-4-240 & STESW-5-240 NEMA 6-20 www.bk-resources.com | orders@bk-resources.com...
18 meses de la fecha de envío de la fábrica. BK Resources reemplazará, sin cargo, cualquier parte defec- tuosa o material de los componentes sobre la demostración de satisfacción de que un incumplimiento de garantía no existió.
STEAM TABLE MANUAL Modèle : STESW- TABLE CHAUDE MANUEL D’INSTALLATION D’UTILISATION POUR VOTRE SÉ CURITÉ : ne pas entreposer ni utiliser des liquides et des vapeurs inammablesà proximité de cet équipement ou de tout autre appareil. Mise en garde : l’installation, l’ajustement, l’altération, l’...
Page 19
Capped Nut 1/4-20 Capped Nut #10-32 x 3/8" Phillips Drive Machine Screw Screw *Note: STESW-2-120 has a qty of 8 Tools Required: Sockets or wrenches for Capped Nuts: 7/16" or 11mm Phillips screwdriver -120 120 Frontage Road, Altamont, IL 62411 | P: 888-310-4393 | F: 618-483-9898 | F: 888-310-4394...
Page 20
STEAM TABLE MANUAL 1. Confirmez que toutes les pièces et tout le matériel sont inclus. 2. A) Placez la Structure à l’envers sur une surface propre afin d’éviter les égratignures. Desserrez les vis à l’intérieur et à l’extérieur de la Structure. Note : ne retirez PAS complètement les vis de la Structure.
Page 21
STEAM TABLE MANUAL 4. A) Fixez les Supports de Tablette Latérale en utilisant les Écrous à Chapeau fournis. Note : ne serrez pas complètement les Écrous à Chapeau. B) Installez la Tablette Latérale sur les Supports de Tablette Latérale. La Tablette Latérale sera posit ionnée entre la Structure et le Support de Tablette Latérale.
Page 22
STESW-5-240 EXPLODED VIEW PARTS LIST Support de Planche à Découper STESW-CBB STESW-CBB STESW-CBB STESW-CBB Description Item STESW-2-120 Item # STESW-3-240 Item # STESW-4-240 Item # STESW-5-240 Item # Planche à Découper STESW-2-CB STESW-3-CB STESW-4-CB STESW-5-CB Cutting Board Bracket STESW-CBB STESW-CBB...
Page 24
3000 NEMA 5-50 3500 STESW-5-240 5-Well 3750 15.6 NEMA 5-50 6-20 5-Well 3750 NEMA 5-50 STESW-5-240 NEMA 5-20 : For STESW-2-120 NEMA 6-20 NEMA L5-30 : For STESW-3-240 NEMA 5-50 : For STESW-4-240 & STESW-5-240 NEMA 6-20 www.bk-resources.com | orders@bk-resources.com...
à compter de la date d’installation initiale, sans dépasser 18 mois à compter de la date d’expédition de l’usine. BK Resources remplacera, sans frais, toute pièce ou tout composant matériel défectueux, après démonstration adéquate qu’il n’y a pas eu violation de la garantie.
Need help?
Do you have a question about the STESW-2-120 and is the answer not in the manual?
Questions and answers