Advertisement
Table of Contents
- 1 Installation
- 2 General Instructions
- 3 Gas Connection
- 4 Electrical Connection
- 5 Special Hints
- 6 Certified Installation
- 7 Methods of Installation
- 8 Ventilation -Heights
- 9 How to Use the Refrigerator
- 10 Instructions for Use
- 11 Electric Equipment
- 12 Gas Equipment
- 13 Ice Making
- 14 Mounting Door Panel
- 15 Panel Dimensions
- Download this manual
REFRIGERATOR FOR LP-GAS AND ELECTRIC OPERATION
RM2300
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Don't touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the vi-
cinity of this or any other appliance.
DSC #308
RM2400
RM2600
quality leisure line products
SERVICE OFFICE
DOMETIC SALES CORP.
509 South Poplar
LaGrange, IN 46761
RM2500
RM2800
Installation
Instructions for use
Gas equipment
Electric equipment
Maintenance
Fault tracing
Door panel
Page
5 - 8
9-10
10
10-11
11
11
12
Advertisement
Table of Contents
Related Manuals for Dometic RM2300
Summary of Contents for Dometic RM2300
- Page 1 DSC #308 RM2400 RM2600 emetic quality leisure line products SERVICE OFFICE DOMETIC SALES CORP. 509 South Poplar LaGrange, IN 46761 RM2500 RM2800 Installation Instructions for use Gas equipment...
- Page 2 REFRIGERATORS WITH PIE20 IGNITER RM2300/2400 @;:aq\ Fig.1 Item Description Retainer Thermo electric safety valve Thermo couple element Coupling Thermostat Cut-off valve Nipple Switch Lighter Burner Electrode Terminal Sealing ring Snap catch Burner housing Burner retainer Terminal 12/120V Burner jet Plug...
- Page 3 REFRIGERATORS WITH AUTOMATIC IGNITION RM2500 Fig.2 Item Description Plug Thermo electric safety valve Thermo couple element Coupling Thermostat Cut-off valve Nipple Switch Reigniter Burner Electrode Terminal block Sealing ring Snap catch Burner housing Terminal block Burner jet Cover Cover Flue baffle Heater Bushing Clamping plate...
- Page 4 REFRIQERATORS WITH AUTOMATIC IQNITION RM2600 RM 2800 Fig.3 Item Description Thermo electric safety valve Thermo couple element Coupling Thermostat Cut-off valve Nipple Switch Reigniter Gas tube Terminal block Snap catch Burner Electrode Terminal block Burner jet Cover Nipple Flue baffle Heater Nipple Flue cap...
-
Page 5: Installation
The 12 V circuit must be fused. Maximum circuit fuse size: 15 Amps. for the models RM2300 and RM2400, 20 Amps. for RM2500, 30 Amps. for RM2600 and 40 Amps. -
Page 6: Special Hints
Be careful not to damage the sealing strip applied to the floor of the enclosure when the refrigerator is put in place. In the front frame and in the base at the rear of the refrigerator there are holes for screws for fixing the refrigerator in the enclo- sure. -
Page 7: Certified Installation
The methods of installation are shown in figures 10 a and 10 b. It is essential that all maxlmum or minimum dimensions are strictly maintained as the performance of the refrigerator is dependent on an adequate flow of air over the rear of the refrigerator. - Page 8 Side 0 L: Bottom 0 M: Rear 1 N: See example below Clearance M between the rearmost part of the refrigerator and the wall behind the refrigerator Clearance N on top of the condenser is related to the minimum ventilation height...
-
Page 9: How To Use The Refrigerator
When the recreational vehicle is stationary it must be leveled to be comfortable to live in. If the refrigerator is properly installed, the freezer shelf parallel to the floor, the refrigerator will then also perform properly. A bubble level should be placed on the freezer shelf. -
Page 10: Electric Equipment
The Igniter The refrigerator is fitted either with a piezo igniter (see fig. 1) or an automatic reigniter (fig. 2 and 3) which does not normally need any maintenance. If the igniter does not work properly contact an authorized service center. -
Page 12: Mounting Door Panel
INSTRUCTIONS FOR MOUNTING THE DOOR PANEL The refrigerator is normally delivered without door panel(s). Before starting the mounting work check that the panel dimen- sions are in compliance with those given in the table and read the instructions through. When mounting the panel, proceed as follows.