Delta Electronics AC Motor Drive VFD-VE Series User Manual page 80

Pr. Explanation
Multi-function Output 1
02-11
RA, RB, RC(Relay1)
Multi-function Output 2
02-12
MRA, MRC (Relay2)
Multi-function Output 3
(MO1)
02-13
Multi-function Output 4
02-14
(MO2)
Multi-function Output 5
02-35
(MO3)
Multi-function Output 6
02-36
(MO4)
Multi-function Output 7
02-37
(MO5)
Multi-function Output 8
02-38
(MO6)
Multi-function Output 9
02-39
(MO7)
Multi-function Output
02-40
10 (MO8)
Multi-function Output
02-41
11 (MO9)
Multi-function Output
02-42
12 (MOA)
Revision August 2008, 03VE, SW V2.04
Settings
44: Reset initial reel diameter
45: Reset initial reel diameter 0
46: Reset initial reel diameter 1
47: Reset PID control integration of tension
48: Mechanical gear ratio switch
49: Reserved
50: Reserved
0: No function
1: Operation indication
2: Operation speed attained
3: Desired frequency attained 1 (Pr.02-19)
4: Desired frequency attained 2 (Pr.02-21)
5: Zero speed (frequency command)
6: Zero speed with stop (frequency command)
7: Over torque (OT1) (Pr.06-06~06-08)
8: Over torque (OT2) (Pr.06-09~06-11)
9: Drive ready
10: User-defined Low-voltage Detection
11: Malfunction indication
12: Mechanical brake release (Pr.02-31)
13: Overheat
14: Software brake signal
15: PID feedback error
16: Slip error (oSL)
17: Terminal count value attained (Pr.02-16)
18: Preliminary count value attained (Pr.02-17)
19: Baseblock (B.B.) Indication
20: Warning output
21: Over voltage warning
22: Over-current stall prevention warning
23: Over-voltage stall prevention warning
24: Operation mode indication
25: Forward command
26: Reverse command
27: Output when current >= Pr.02-32
28: Output when current < Pr.02-32
29: Output when frequency >= Pr.02-33
30: Output when frequency < Pr.02-33
31: Y-connection for the motor coil
32: Δ connection for the motor coil
33: Zero speed (actual output frequency)
34: Zero speed with Stop (actual output frequency)
35: Error output selection 1 (Pr.06-23)
36: Error output selection 2 (Pr.06-24)
37: Error output selection 3 (Pr.06-25)
38: Error output selection 4 (Pr.06-26)
39: Position attained (Pr.10-19)
40: Speed attained (including zero speed)
41: Multi-position attained
42: Crane function
43: Motor zero-speed output (Pr.02-43)
44: Max. reel diameter attained
45: Empty reel diameter attained
46: Broken belt detection
47: Break release at stop
48: Error PID feedback of tension
49: Reserved
Chapter 4 Parameters|
Factory
VF VFPG SVC FOCPG TQRPG
Setting
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○
11
○ ○ ○ ○
○ ○ ○ ○
1
○ ○ ○ ○
○ ○ ○ ○
0
○ ○ ○ ○
0
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
0
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○
○ ○ ○ ○
○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
4-31