Motion Detecting Control Panel Models Cmxeocg772 And Cmxeocg982 - Craftsman CMXEOCG322 Owner's Manual

MOTION DETECTING CONTROL PANEL
MODELS CMXEOCG772 AND CMXEOCG982
SYNCHRONIZE THE DOOR CONTROL: To synchronize the door
control to the garage door opener, press the push bar until the garage
door opener activates (it may take up to 3 presses). Test the door
control by pressing the push bar; each press of the push bar will
activate the garage door opener.
Push Bar
1, 5, and
10 Minute HOLD OPEN
TTC LED
Button(TTC)
LIGHT Button
Motion Sensor
PUSH BAR: Press the push bar to open or close the door.
LIGHT BUTTON: Press the LIGHT button to turn the garage door
opener lights on or off. When the lights are turned on they will stay on
until the LIGHT button is pressed again, or until the garage door
opener is activated. Once the garage door opener is activated the
lights will turn off after the specified period of time (the factory default
is 4-1/2 minutes). The LIGHT button will not control the lights when
the door is in motion.
To change the amount of time the lights stay on:
Press and hold the LOCK button (approximately 10 seconds) until the
garage door opener lights flash. The time interval is indicated by the
number of times the garage door opener lights flash:
• 1 flash is 1-1/2 minutes
• 2 flashes is 2-1/2 minutes
• 3 flashes is 3-1/2 minutes
• 4 flashes is 4-1/2 minutes
To cycle through the time intervals repeat the step above. If the push
bar LED is continuously blinking, the LOCK feature needs to be
turned off.
Motion Sensor Switch
Command LED
LEARN Button
LOCK Button
LEARN BUTTON: Any compatible remote control, wireless keypad,
®
or myQ devices can be programmed to the garage door using the
LEARN button.
MOTION SENSOR: The motion sensor automatically turns on the
garage door opener lights when motion is detected. The lights come
on for the set period of time, and then shut off. If using the garage
door opener light as a work light disable the motion sensor, otherwise
the lights may turn off automatically if you are beyond the range of the
motion sensor.
ON (TTC)
OFF (TTC)
The motion sensor switch turns the motion sensor on or off.
LOCK: Prevents the garage door opener from being activated by
remote controls while still allowing activation from the door control
and wireless keypad.
Turn ON:
Press and hold the LOCK button for 2 seconds. The command LED
will flash as long as the lock feature is on.
Turn OFF:
Press and hold the LOCK button for 2 seconds. The command LED
will stop flashing and normal operation will resume.
TIMER-TO-CLOSE (TTC) (Factory default is set to off): The Timer-
to-Close feature automatically closes the door after a specified time
period and can be adjusted using the door control. DO NOT enable
TTC if operating a one-piece door. TTC is to be used ONLY with
sectional doors. The garage door opener will beep and the lights will
flash before closing the door. The TTC feature will deactivate if the
garage door encounters an obstruction twice; or the safety reversing
sensors are incorrectly installed. The garage door will reverse open
and WILL NOT close until the obstructions are clear or the safety
reversing sensors are correctly installed. When the obstruction has
been cleared or the safety reversing sensors have been aligned, the
door will close when the garage door opener is activated. TTC WILL
NOT work if the garage door opener is operating by battery power or if
the safety reversing sensors are misaligned. This feature is NOT
intended to be the primary method of closing the door. A wireless
keypad should be installed in the event of an accidental lock out when
using this feature.
To turn TTC on or off or to set the TTC time interval:
Turn ON:
1. Press and hold the ON button until one of the TTC LEDs light
up.
2. Then press the ON button again to cycle through the time
interval options. The TTC time interval can be set to 1, 5, and
10 minutes (the corresponding TTC LED will light for each
time interval). The garage door opener light bulbs will blink as
confirmation. Once the TTC has been set and the door is
open, the TTC LED for the selected time interval will blink and
begin to count down to close the door.
Turn OFF:
1. Press and hold the OFF button until all TTC LEDs turn off and
a beep is heard from the garage door opener.
Temporarily hold door open (suspend TTC):
1. Press and release the HOLD OPEN button.
2. Press the HOLD OPEN button again to resume normal TTC
operation.
36