Table of Contents
Advertisement
Quick Links
Group 1
1.1 Table of contents
1.1 Table of contents ............................................................................................................ 1
1.2 Group directory............................................................................................................... 7
1.3 Menu level index............................................................................................................. 8
1.4 Publisher....................................................................................................................... 10
1.5 Introduction................................................................................................................... 12
1.6 Document information .................................................................................................. 13
2. Safety................................................................................................................................. 14
2.1 Scope of risks ............................................................................................................... 14
2.2 Safety instructions and recommendations.................................................................... 14
2.3 Intended use................................................................................................................. 17
2.4 Sources of danger ........................................................................................................ 17
2.5 Safety sticker ................................................................................................................ 21
2.6 Operating staff .............................................................................................................. 22
2.7 Dangers due to electric energy..................................................................................... 22
2.8 Personal protective equipment ..................................................................................... 22
2.9 Protective devices ........................................................................................................ 22
2.10 Safety measures at the place of installation ............................................................... 23
2.11 Dangers through consumables................................................................................... 23
3. Accident prevention.........................................................................................................25
3.1 Storage and handling (normal use) .............................................................................. 25
3.2 First aid measures ........................................................................................................ 26
3.3 Fire fighting measures .................................................................................................. 26
3.4 Measures in the event of accidental release (spillage)................................................. 27
4. Technical data .................................................................................................................. 28
4.1 Dimensions, weights, connections ............................................................................... 28
4.2 Ambient conditions ....................................................................................................... 28
4.3 System interfaces ......................................................................................................... 28
4.4 Power parameters ........................................................................................................ 29
4.5 Font forms .................................................................................................................... 29
4.6 Forms of printing........................................................................................................... 30
4.7 Font combinations ........................................................................................................ 30
4.8 Manner of working ........................................................................................................ 30
4.9 Software ....................................................................................................................... 31
5. Transport/Start up ............................................................................................................ 32
Release 3.00
Table of contents
Page 1
Leibinger-Jet 2 se
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Leibinger Jet 2
Summary of Contents for Leibinger Jet 2
-
Page 1: Table Of Contents
4.4 Power parameters ......................29 4.5 Font forms ........................29 4.6 Forms of printing......................30 4.7 Font combinations ......................30 4.8 Manner of working ......................30 4.9 Software ........................31 5. Transport/Start up ......................32 Release 3.00 Leibinger-Jet 2 se... -
Page 2: Table Of Contents
6.3.1.3 Status line in normal operation..............50 6.3.1.4 Status line in error condition................50 6.3.1.5 Software Reset....................51 6.3.2 Ink switch ......................52 6.3.3 Hardware Reset ....................52 6.3.4 Potentiometer – Display illumination ..............53 6.3.5 Menu structure .....................54 6.4 Interfaces........................57 Release 3.00 Leibinger-Jet 2 se... - Page 3 7.2.5 Graphics editor.....................79 7.2.6 Shift code input ....................80 7.2.7 Barcode input.......................82 7.2.7.1 Barcode information ..................82 7.2.7.2 Barcode selection..................84 7.2.7.3 Barcode parameter..................85 7.3 Job administration ......................86 7.3.1 Opening job......................86 7.3.2 Factory setting & default jobs................87 Release 3.00 Leibinger-Jet 2 se...
- Page 4 7.7.1 Direct start and time/date ...................112 7.7.2 Monitoring functions (Control functions).............113 7.7.2.1 Printgo- and strokego monitoring ..............113 7.7.3 Encoder......................114 7.7.4 Encoder parameters...................114 7.7.5 Job change ......................115 7.7.5.1 Printing with the function “external job selection” ........115 7.7.6 Service/test- and diagnosis functions..............117 Release 3.00 Leibinger-Jet 2 se...
- Page 5 9.4.1.1 Cleaning the print head ................144 9.4.1.2 Cleaning the deflector unit and gutter ............145 9.4.2 Weekly cleaning work ..................146 9.4.2.1 Cleaning of the spindle and guides of the nozzle seal ........146 9.4.3 Other cleaning work ...................147 Release 3.00 Leibinger-Jet 2 se...
- Page 6 12.2 Interface layout plan ....................159 12.3 Calculation of the print speed ................... 161 12.4 Fonts......................... 164 12.5 List of graphics ......................166 12.6 Technical drawings....................167 List of keywords/Index....................... 169 List of illustrations ......................175 Release 3.00 Leibinger-Jet 2 se...
-
Page 7: Group Directory
Hydraulics diagram ..................158 Interface layout plan ..................159 Calculation of the print speed ..............161 Fonts......................164 List of graphics .................... 166 Technical drawings ..................167 Index ......................169 List of illustrations ..................175 Release 3.00 Leibinger-Jet 2 se... -
Page 8: Menu Level Index
7.7.6.3 Menu level 16, 38, 39 ............119 7.7.6.4 Menu level 16, 35 ..............120 7.7.6.5 Menu level 16, 34 ..............120 7.7.6.6 Menu level 16, 29 ..............121 7.7.6.6 Menu level 43 ............... 122 Release 3.00 Leibinger-Jet 2 se... - Page 9 Group 1 Menu level index Page 9 7.7.6.7 Menu level 16, 59 ..............123 7.7.6.8 Menu level 16, 64 ..............124 Release 3.00 Leibinger-Jet 2 se...
-
Page 10: Publisher
Group 1 Publisher Page 10 1.4 Publisher For questions regarding the operation and running of the LEIBINGER-JET 2 as well as in service case please contact the listed dealer address. Dealer address Paul Leibinger GmbH & Co. KG Special factories for numbering machines Daimlerstraße 14... - Page 11 Nevertheless errors cannot be excluded. Consequently no guarantee can be assumed for the correctness of the content of this manual and no claims can be asserted against Paul Leibinger GmbH & Co. KG. We shall be grateful for information regarding possible printing errors as well as for suggestions for the further optimisation of the device manual.
-
Page 12: Introduction
It is only through the use of inks and solvents from Paul Leibinger GmbH & Co. KG that optimum operating characteristics can be achieved. Should other inks and solvents be used all guarantee claims will expire. -
Page 13: Document Information
Group 1 Introduction Page 13 1.6 Document information The instruction Release 3.00 of 17 February 2006 is valid for Leibinger-Jet 2 se machines from the software-version V40.1.00.00. Release 3.00 Leibinger-Jet 2 se... -
Page 14: Safety
Page 14 2. Safety 2.1 Scope of risks The high performance printer LEIBINGER- JET 2 has been built in accordance with state-of- the-art standards and recognized safety requirements and has been equipped with protective devices. Operational and safety checks of the installation were carried out before it left the factory. In... - Page 15 Failure to observe this instruction can lead to material damage, the loss of guarantee and to injury! Indicates service activities! This work must only be carried out by trained personnel or by Leibinger service technicians! Release 3.00 Leibinger-Jet 2 se...
- Page 16 Group 2 Safety instructions Page 16 Indicates important user information for safe and effective working. Indicates recommendations for use and other useful pieces of information. Release 3.00 Leibinger-Jet 2 se...
-
Page 17: Intended Use
Page 17 2.3 Intended use The high performance printer LEIBINGER-JET 2 serves exclusively the contact-free marking, inscribing and coding of surfaces using the continuous ink jet process. The high performance printer can be used on the most varying materials (e.g. metal, synthetic material, glass, paper, wood, pressed materials, rubber etc.) with both, smooth as... - Page 18 Parts of the device are still under voltage after blowing the protecting device! Disconnect the device from the main supply prior to opening. Remove mains plug! Dangerous electrical voltage! Measurement under voltage has carried out only by electrical experts! Release 3.00 Leibinger-Jet 2 se...
- Page 19 Dangerous material in the machine! Danger of serious damage through burns, skin irriation and poisoning! Warning! Read and understand the device manual before using this machine. Incorrect operation can lead to injury or damage to the device! Release 3.00 Leibinger-Jet 2 se...
- Page 20 Risk of injury! Ink escapes from the head aperture. Spraying of ink into the eyes can cause blindness. Eye protection is necessary! Risk of injury! Upon contact the contents causes skin irritation. Protective equipment is necessary! Release 3.00 Leibinger-Jet 2 se...
-
Page 21: Safety Sticker
Group 2 Safety instructions Page 21 2.5 Safety sticker Figure 1 Release 3.00 Leibinger-Jet 2 se... -
Page 22: Operating Staff
2.6 Operating staff Only trained personnel must operate the device. The personnel must have appropriate training to enable them to be able to operate the LEIBINGER-JET 2 high performance printer professionally. Within the working area of the LEIBINGER-JET 2 device the operator is responsible with regard to third parties. -
Page 23: Safety Measures At The Place Of Installation
(residue of lubricants etc.). The working place surroundings should be kept clean at all times in order to ensure unrestricted access to the LEIBINGER-JET 2 device. 2.11 Dangers through consumables Inks are coloured liquids on a water or solvent basis. The safety instructions on the containers of the consumables as well as the instructions in the group Accident prevention must be especially adhered to in order to exclude dangers for persons and the surroundings. - Page 24 52900 of the inks and solvents used. Upon written request we shall be pleased to send you a copy. Please indicate the Leibinger article no. in all cases. In the following you will find examples for the marking of inks and solvents.
-
Page 25: Accident Prevention
Keep sources of heat and sparks as well as open flames well away. Use only spark-free tools. Electrical devices must be protected in accordance with the corresponding standard. Avoid contact with the skin and eyes. Do not inhale vapours and spray mist. Release 3.00 Leibinger-Jet 2 se... -
Page 26: First Aid Measures
Decomposition products can constitute a danger to health. Extinguishing waste water must not enter the waste water channels or waters. PROTECTIVE If necessary suitable, independent breathing apparatus is required. MEASURES Release 3.00 Leibinger-Jet 2 se... -
Page 27: Measures In The Event Of Accidental Release (Spillage)
Restrict and suck up spilled substances with a non-combustible absorbent material (e.g. sand, earth, vermiculite, infusorial earth) and collect in a suitable container for removal. Preferably clean areas with spilled substances with a detergent. Avoid solvents. Release 3.00 Leibinger-Jet 2 se... -
Page 28: Technical Data
5-pole connection bush, 24 V, 100 mA, for optical, inductive, capacitive proximity switch NPN/PNP types Pressure synchronisation: Digital incremental shaft encoder with 12-pole bush on (optional) the rear side of the cabinet (5 V, EIA 422 A) Release 3.00 Leibinger-Jet 2 se... -
Page 29: Power Parameters
Capitals and non-capitals, umlauts, special characters Matrix forms: 5x5, 7x5, 9x5, 9x7, 16x10, 11x8, 12x8, 14x10, 24x24, Bern 16 (16x11-matrix), Bern 24 (24x18-matrix) Barm 16 (16x12-matrix) Graphics Graphics character record Graphics 1 to 24 dot Bold print Contrast type Release 3.00 Leibinger-Jet 2 se... -
Page 30: Forms Of Printing
! Automatic jet closure, the print head is ready for writing immediately following starting up ! Automatic, electronic drop call-off regulation for compensating changing ambient operating temperatures. ! Automatic viscosity regulation ! Ability to refill ink and solvent during writing operation Release 3.00 Leibinger-Jet 2 se... -
Page 31: Software
! Job administration allows the storage and the calling up of texts and of all print relevant parameters ! Bar codes (e.g. bar code 39, EAN 8/13 and code 2/5 interleaved) ! Text organiser ! Counter marking ! Shift operation Release 3.00 Leibinger-Jet 2 se... -
Page 32: Transport/Start Up
In order to avoid damage during transport the following instructions must be observed. The LEIBINGER-JET 2 must only be transported in a standing position. It is packed in a cardboard box with special polystyrene inserts for safe dispatch during delivery. Transport of the device must only be made in this packing in order to avoid damage. -
Page 33: Installation
The LEIBINGER- JET 2 must be connected to alternating current 115 - 230 V AC, 47 – 60 Hz with a corresponding plug. The plug socket should be equipped with a clear marking (e.g.: LEIBINGER-JET 2). -
Page 34: Data Interface X2
Page 34 5.3.2 Data interface X2 The operation of the LEIBINGER-JET 2 is normally done via the LCD touch display. The RS 232 input on the rear side of the device (9-pole plug, female, interface X2) can be used as an external data interface for connection to a PC, notebook or host. The standard baud rate is 38400 Baud. -
Page 35: Pin Assignment Plan
! PIN 8 CTS ! PIN 9 +5 VDC supply voltage for programming device (max. 0.5 A) When entering the data the respective description must be observed. Leibinger offers a correspondingly protected cable for the connection. Data connection cable PC to LEIBINGER- JET 2: 54-002 295 SA... -
Page 36: Print Go Interface X5
The transmission ratio between product and shaft encoder speed should be selected in such a manner that a maximum output frequency of 150 kHz is not exceeded. Shaft encoders with 1000, 2500, 5000 and 10000 impulses/revolution are avaiable. Release 3.00 Leibinger-Jet 2 se... -
Page 37: Mechanic Installation
Group 5 Transport/start up Page 37 Leibinger ordering number: see group replacement parts With more difficult operating conditions (dust or humidity) shaft encoders with IP 66 form of protection should be used. Figure 9 Pin assignment Signal Colour 0,5mm² 0,5mm²... -
Page 38: Print Head
The operating staff must not be exposed to danger due to the installation of the device in a production plant. Moving products under the print head may cause risk of crushing/cutting. The instructions of the machines directive must be strictly adhered to. Release 3.00 Leibinger-Jet 2 se... -
Page 39: Start Up
Details of the filling process can be found in the group Equipping/maintenance in the chapter Refilling of ink and solvent! Recreate mains connection and switch on the LEIBINGER-JET 2 with the LCD touch display. Details on the switching on procedure can be found in the group Operation in the chapter Operating procedures and operating elements! Following switching on the device is bleed automatically i.e. - Page 40 Place on the head cover of the print head and press the status field <nozzle closed>. The jet opens and the status display changes. If the notification “Print Yes” appears in the status field <print> the LEIBINGER-JET 2 is ready for operation. The data can now be entered as described in the group Operation in the chapter Operating procedures and operating elements as well as in the group Data entry.
-
Page 41: Initial Start Up In A Full Condition
Switch on ink switch (ink on – switch upwards). Recreate mains connection and switch on the LEIBINGER-JET 2 with the LCD touch display. Details on the switching on procedure can be found in the group Operation in the chapter Operating procedures and operating elements! Following switching on the device is bleed automatically i.e. - Page 42 Place the head cover of the print head back on again. If the notification “Print Yes” appears in the status field <print> the LEIBINGER-JET 2 is ready for operation. The data can now be entered as described in the group Operation in the chapter Operating procedures and operating elements as well as in the group Data entry.
-
Page 43: Operation
4 – Refill unit 5 – Print head with head umbilical The fundamental electronic components of the LEIBINGER- JET 2 such as the mains part, the LCD touch display and the controller board are accommodated in the electronics cabinet. The LCD touch display serves the display of the system conditions of the LEIBINGER-JET 2 and the operation of the device. -
Page 44: Functional Principle
6.2 Functional principle 6.2.1 Method of working The Leibinger-Jet 2 works in accordance with the continuous ink jet process. In this a constant ink jet is emitted from a jet nozzle which is broken down into a series of equal size drops under the influence of mechanical oscillations. -
Page 45: Drop Deflection
The values needed for generating the charge voltages for each individual character are stored in memory devices (FPROMS) on the controller board. Release 3.00 Leibinger-Jet 2 se... -
Page 46: Summary Of The Individual Procedures
Character „E“ build with a 7 x 5 matrix Rel. movement direction of the description area Drop brake-off point Abriss-Punkt Gutter Deflector plate Charge electrode with deflector electrode Nozzle (jet) Oscillator Creation of a character Release 3.00 Leibinger-Jet 2 se... -
Page 47: Operating Procedures And Operating Elements
6.3.1 LCD touch display 6.3.1.1 Switching on/switching off procedure Figure 14 The LEIBINGER-JET 2 is switched on by touching any point of the touch display (1) that is still dark. Contact duration approx. 2 sec. The start screen with the software-version number (2) and the execution identification (3) are displayed for 3 sec.. - Page 48 <printstop>. To be able to perform a print order a text must have been entered or an existing job selected. Further information on this subject can be found in the group Data entry in the chapters Text administration and job administration! Release 3.00 Leibinger-Jet 2 se...
-
Page 49: Interval Operation
[E43] In the switched off state the integrated interval function activates the LEIBINGER-JET 2 automatically in accordance with the times set in the menu level <E43> (“Main menu ! service/test/ system parameter ! service/test & diagnostics ! hydraulic test &... -
Page 50: Status Line In Normal Operation
The error is acknowledged by touching the touch field <Error notification> (status line). Figure 18 Status line with error notifications (specimen illustration) [E1] Release 3.00 Leibinger-Jet 2 se... -
Page 51: Software Reset
! The finger has to stay in this position until the square has disappeared and must not taken away before! Attention! Keep the square pressed until it has disappeared. Release 3.00 Leibinger-Jet 2 se... -
Page 52: Ink Switch
Figure 20 1 – Ink switch 6.3.3 Hardware Reset Reset switch: Enables the resetting of the electronics in the event of an error. It is accommodated in the electronics cabinet. Figure 21 1 – Reset switch Release 3.00 Leibinger-Jet 2 se... -
Page 53: Potentiometer - Display Illumination
The potentiometer is located in the electronics cabinet on the controller board (also see figure in chapter 6.5.2). Figure 22 1– Potentiometer - Display illumination Release 3.00 Leibinger-Jet 2 se... -
Page 54: Menu Structure
Group 6 Operation – procedures and elements Page 54 6.3.5 Menu structure Release 3.00 Leibinger-Jet 2 se... - Page 55 Group 6 Operation – procedures and elements Page 55 Release 3.00 Leibinger-Jet 2 se...
- Page 56 Group 6 Operation – procedures and elements Page 56 Release 3.00 Leibinger-Jet 2 se...
-
Page 57: Interfaces
Article no.: see group Replacement parts – periphery Shaft encoder Should alternative shaft encoders be used the minimum impulse issue should be 3 impulses/mm in order to achieve an efficient resolution! Release 3.00 Leibinger-Jet 2 se... -
Page 58: Optional Outputs
6.4.4 Optional outputs 7 outputs NPN 24 V, 500 mA are available (please see chapter 12.2 "Interface layout plan"). 6.4.5 Optional inputs 12 potential-free inputs are available for special functions(please see chapter 12.2 "Interface layout plan"). Release 3.00 Leibinger-Jet 2 se... -
Page 59: Description Of The Device
Disconnect the device from the mains supply prior to opening. Remove mains plug! The fundamental electronic components of the LEIBINGER-JET 2 such as the mains part, the LCD touch display and the controller board are accommodated in the electronics cabinet. -
Page 60: Controller Board
The controller board contains the logic (CPU) and the power switching circuits of the LEIBINGER-JET 2. Figure 27 Controller board (conductor plate) LEIBINGER-JET 2 (54-003 333 S) 1 – Data interface RS 232 (RS 422 optional) 2 – Battery, lithium, 3.2 VDC (54-003 032 KA) 3 –... - Page 61 ! Control and position monitoring of the automatic nozzle sealing ! Administration of date, time and expiration date with the clock module ! Creation of the oscillator voltage and of the charging voltage ! Drive of the hydraulic components Release 3.00 Leibinger-Jet 2 se...
-
Page 62: Dc Power Supply
Disconnect the device from the mains supply prior to opening. Remove mains plug! The direct currents of the LEIBINGER-JET 2 are achieved through a power supply with automatic input voltage recognition. It has "Power Factor Compensation" and is permanently short circuit resistant or switches off independently in the event of overload. -
Page 63: Hydraulics Part
The hydraulic parts are made accessible for service purposes through opening of the fastening screws and removal of the rear wall (see illustration). This work must only be carried out by trained personnel or by Leibinger service technicians! Release 3.00 Leibinger-Jet 2 se... - Page 64 13 – Mixing valve “Ink/solvent” 5 – Filter 14 –Storage tank “Ink” 6 – Viscometer 15 – Storage tank “Solvent” 7 – Viscosity pump 16 – Leak sensor 8 – Air discharge (used air) valve (with choke) Release 3.00 Leibinger-Jet 2 se...
-
Page 65: Main Pump
<E29> “Hydraulics test & parameters”. Main pump (54-002 001 S) The function of the LEIBINGER-JET 2 or the creation of the ink pressure presupposes the functioning of the compressor. 6.5.4.2 Suction pump The suction pump is a membrane Figure 32 pump and is used for sucking up the ink from the gutter. -
Page 66: Viscosity Control
Spraying of ink into the eyes can cause blindness. Prior to the opening of the device eye protection must be put on! For process-safe functioning of the LEIBINGER-JET 2 it is necessary to keep the viscosity of the ink constant. During operation the ink gives off solvent into the ambient air. -
Page 67: Leak Detection
Page 67 6.5.4.4 Leak detection An additional safety measure in the LEIBINGER-JET 2 is the leak detection. To detect a leak in the hydraulic part i.e. if ink or solvent on the basis of slightly combustible solvents escape, the operation of the device is aborted and an acoustic alarm triggered. - Page 68 10 – Ink feed tube 5 – Jet fixing screw with bar 11 – Bleeding tube 6 – Head electronic 12 – Head filter This work must only be carried out by trained personnel or by Leibinger service technicians! Release 3.00 Leibinger-Jet 2 se...
-
Page 69: Drop Production Unit With Oscillator
Figure 38 1 – Charge electrode 2 – Deflector plate Deflector unit Replacement and changings at the deflector unit! This work must only be carried out by trained personnel or by Leibinger service technicians! Release 3.00 Leibinger-Jet 2 se... -
Page 70: Nozzle Plate
Figure 39 Nozzle seal 1 – Drive motor 2 – Guide shaft 3 – Toggle lever for arresting for cleaning purposes 4 – Jet (nozzle) adjustment screw (left/right) 5 – Jet (nozzle) adjustment screw (up/down) Release 3.00 Leibinger-Jet 2 se... -
Page 71: Data Entry/Programming
7. Data entry/programming 7.1 General Data that is to be printed by the Leibinger-Jet 2 can be entered, called-up, altered and stored with various programming devices, PC’s etc.. Below is a description of the programming with the LCD touch display. -
Page 72: Text Entry
Following the selection of the font, the line menu <E15> is opened. By means of pressing the corresponding touch field the number of lines or the desired line position can be selected. entry e.g. single line = <one line> (10) [E15] Release 3.00 Leibinger-Jet 2 se... -
Page 73: Bold Print
There are two expiry dates available (expday1...+ expday2...), which can be programmed any way. If the Leibinger-Jet 2 is used in shift operation the function <shift > (15) will be available. You will find further information regarding this topic in the chapters Shift code input and Expiration-and shift times.! - Page 74 Data Entry Page 74 Manner of proceeding: Example: It should be written „LEIBINGER SAMPLE NOT FOR SALE. ! Press the touch field <Text new> in the menu level <E3>. ! The „font menu“ <E9> will be called up. ! After choosing the font the line menu <E15> either the keyboard field <E50> will be displayed if necessary.
-
Page 75: Font Parameters
24 dot) for fast barcode printing and draftmode 4 (24 dot) for etremley small fonts. Draftmode 5 was specially customized for fast printing of graphics and fonts with a height of 11 dots (e.g. chineese characters). Release 3.00 Leibinger-Jet 2 se... - Page 76 To reach a bold print several drops are placed next to each other, that means e.g. if the bold value is set to „1“ on the print-out 2 drops will be placed next to each other. Release 3.00 Leibinger-Jet 2 se...
- Page 77 <E15>. For the first line graphics or text can be selected, in the second line only text can be entered. In all selection fields the current status or the current values are shown simultaneously! Release 3.00 Leibinger-Jet 2 se...
-
Page 78: Text Editor
The real graphic will be only shown in the menu level <E1>. You will find a list with the saved graphics with it’s reference in the enclosure of this manual! The max. height of graphics is 24 dots. Release 3.00 Leibinger-Jet 2 se... -
Page 79: Graphics Editor
The graphic displayed can now be deleted, altered or stored. [E3] [E10] [E19] To alter graphics the grid on the corresponding screens is tapped on. As a result pixels are added or deleted. Release 3.00 Leibinger-Jet 2 se... -
Page 80: Shift Code Input
! By the touch field <Shift> (40) scroll as long as the menu level <E60> appears. ! Press the touch field <Shift > (41). The Leibinger-Jet 2 changes to the shift definition mode. T To indicate that the shift definition mode is active, the display background will be colored black. - Page 81 Group 7 Data Entry Page 81 Figure 54 [E60] [E50] Activate the shift Input text [E50] [E60] Input shift designation [E60] [E52] Confirm the input Input data delimiter [E1] Taking over to the production Release 3.00 Leibinger-Jet 2 se...
-
Page 82: Barcode Input
! only numerical code (only numbers from 0-9 can be displayed) ! only an even amount of digits is valid Code 39: ! alphanumerical code ! (is available with or without Gothic character (clear figure) for the Leibinger- Jet 2.) EAN 8: ! (only numbers from 0-9 can be displayed) - Page 83 ! numeric code (only numbers from 0-9 can be displayed) ! has to be always 12-digits (11 performance characters and 1 check digit) ! (is available with or without clear figure for the Leibinger-Jet 2) UPC E: (American equivalent to EAN8)
-
Page 84: Barcode Selection
You will find further information in the chapter Text entry. [E9] [E17] Note! The Leibinger-Jet 2 does not carry out any check digit calculations generally. This has to be carried out external in advance! Release 3.00 Leibinger-Jet 2 se... -
Page 85: Barcode Parameter
Barcode. This enables e.g. the print-out of a Barcode with white ink on dark background. Example: 2 of 5 interleaved normal (print-out with dark ink on light background) inverse (print-out with light ink on dark background) Calm area Calm area Release 3.00 Leibinger-Jet 2 se... -
Page 86: Job Administration
128 Jobs can be saved. In the job – list 32 jobs are shown per page. The job – pages can be leafed through with the touch field <next> (64). [E45] Entry; e.g.: LJTEST =<LJTEST>(63) Release 3.00 Leibinger-Jet 2 se... -
Page 87: Factory Setting & Default Jobs
If all jobs deposited have been deleted in advance then all jobs (up to “E”) will automatically be loaded as illustrated in the job administration menu <E45> (main menu – jobs menu – load job). Release 3.00 Leibinger-Jet 2 se... -
Page 88: Deleting Jobs
<Delete> (70) the job is effectively deleted and the display is updated. ! Further jobs can be selected for deletion. [E49] ! By means of touching the touch field <ESCAPE> (71) the menu can be ended without making alterations. Release 3.00 Leibinger-Jet 2 se... -
Page 89: Storing And Listing Jobs
Further more there is also the optional possibility to download all jobs to a PC for protection of saved data! For this you will need a special connection cable as well as the Leibinger program”LJ-Flash”. Release 3.00 Leibinger-Jet 2 se... -
Page 90: User-/ Password Administration
Page 90 7.4 User-/ Password administration The LEIBINGER-JET 2 offers the possibility to assign different access rights with different user groups to minimize malfunctions during the production process. Note! For delivery is no password given therefore all functions are released. -
Page 91: Call Up Password Administration
To activate the user administration the password for the Supervisor has to be entered. The passwords should have min. 4 characters. The max. amount of the characters is limited to 10 characters. Manner of proceeding Figure 66 [E7] [E50] Enter password [E7] Release 3.00 Leibinger-Jet 2 se... -
Page 92: User Change And Password Change
! The keyboard field <E50> opens to enter the password. ! Enter the requested password and confirm it with the touch field <RET> (83). ! The LEIBINGER-JET 2 changes back to the password administration menu <E7>. The device starts always with the password level 3 (operator-... -
Page 93: Login As Supervisor Or Advanced Operator
! The keyboard field <E50> opens to enter one of the given passwords. ! Enter the required password and confirm it with the touch field <RET> (86). ! The selected user will be loged in and the LEIBINGER-JET 2 changes back to the password administration menu <E7>. - Page 94 Group 7 Data Entry Page 94 Figure 68 [E2] [E7] [E7] [E50] Enter password [E7] [E50] Enter new password The password should have at least 4 characters and should not exceed 10 characters. Release 3.00 Leibinger-Jet 2 se...
-
Page 95: Logoff As Supervisor Or Advanced Operator
Page 95 7.4.4.3 Logoff as supervisor or advanced operator To log off as supervisor or advanced operator either to reset the LEIBINGER-JET 2 to the operator-mode you have to proceed as following: ! Press the touch field <password management> (90) in the menu level <E2>. -
Page 96: Password Forgotten
! The LEIBINGER-JET 2 changes back to the password administration menu. <E7>. ! Press the touch field <change superuser> (96). ! Enter the text „LEIBINGER“ and leave the menu level with the touch field <RET> (97). ! The user administration will be deactivated and the LEIBINGER-JET 2 changes back to the password administration menu <E7>. - Page 97 Group 7 Data Entry Page 97 Figure 70 [E2] [E7] [E7] [E50] Enter password [E7] [E50] Enter text „LEIBINGER“ [E2] Release 3.00 Leibinger-Jet 2 se...
-
Page 98: Print Start Parameters
The touch field <print repeat> (103) enables the entry of the number of print-outs, at the same time the current value is also displayed in the field. Values between 0-255 are admissible. Example: 000 = single print-out 255 = endless repetition 001 = double print-out Release 3.00 Leibinger-Jet 2 se... -
Page 99: Printgo Distance
Major speed alterations require the droplet flight time compensation for the prevention of text item variances. A precondition is the setting of a greater print delay because at higher speeds the droplet loading must [E4] start earlier. Release 3.00 Leibinger-Jet 2 se... -
Page 100: Print Go And Print Go Gate
“ON” activated the print procedure is only carried out for as long as the queried sensor is under voltage. Example: Endless print-out of pipes with interrupts between the end of the previos pipe and the beginning of the next pipe. Release 3.00 Leibinger-Jet 2 se... -
Page 101: Meter Go Function
Data Entry Page 101 7.5.5 Meter go function Figure 76 With the touch field <Meter-Go> (108) the Leibinger-Jet 2 function will be activated or deactivated. At the same time the current status „ON“ or „OFF“ is displayed. [E4] Function: The function enables to continue the running production for the printing of continuous goods during a printing stop and enables to continue the print with the correct status after the stop. - Page 102 The touch field <take over > (114) will be only displayed during open nozzle! Note! To guarantee the correct start value for the first „printing start“ with the function it is absolutely necessary that all counters are reset accordingly. Figure 77 [E8] [E4] [E1] Release 3.00 Leibinger-Jet 2 se...
-
Page 103: Pre-Defined Print Stop
With the touch field <stop after x PG> (115) the amount of print-outs are pre- defined and according to this the Leibinger- Jet 2 will release an automatic printing stop. At the same time the entered value is displayed in the field. -
Page 104: Function Parameters
Two times can be entered. Return <ret>(124)=take over entry [E41] Backspace <bs> (125)=delete the last entry By activation of the corresponding <touch field> (126) the times can be entered via the number block appearing. [E44] Release 3.00 Leibinger-Jet 2 se... -
Page 105: Replacements And Text Sources
(e.g. 4 wildcards are defined ! always necessary to send 4 data bytes per print-out). The characters can include letters and numbers, but should not include control characters as “carriage return” or “line feed”. Release 3.00 Leibinger-Jet 2 se... - Page 106 Now the second data record has to be transferred via the interface (this transmission can already happen during the first print-out) => e.g. “2345” After the next “PrintGo”-signal the following text will be printed out: Content 2345 pieces Release 3.00 Leibinger-Jet 2 se...
-
Page 107: Reset Counters
(132) and <reset count. 2> (133) the respective counter is reset. (Resetting of counters actually printed out.) [E6] The “counter 1” can also be reseted by an external 24V-signal ona pin 15/X4 (please see chapter 12.2 "Interface layout plan") Release 3.00 Leibinger-Jet 2 se... -
Page 108: Counter Settings
The touch field <reset> (141) controls the form of the reset. At the same time the activated status „normal“ or „Prod. C.“ is displayed in the field. If the function „Prod. C.“ (with product counter) is activated the counter will be reset when the product counter is reset. Release 3.00 Leibinger-Jet 2 se... -
Page 109: Counter Programming
! By the touch field <Shift> scroll as long as the menu level <E60> appears. ! Press the touch field <Counter> (142). The Leibinger-Jet 2 changes to the counter definition mode. To indicate that the counter definition mode is active, the display background will be colored black. - Page 110 If the counter should start counting from the beginning from the initial value (e.g. 05) the wildcard has to correspond with the initial value (wildcard value = 05). Figure 85 [E50] [E60] Activate counter Input wildcard for counter [E60] [E1] Taking over to printing process Confirm input Release 3.00 Leibinger-Jet 2 se...
-
Page 111: Mode Normal And Reflected
The necessary length of the print go delay is depended of the printing speed and has to be find out by some trials. Recommended is a default value of 5 mm! Release 3.00 Leibinger-Jet 2 se... -
Page 112: Service/Test/System Parameters
[E8] I.e. when the print head is opened, the oscillator voltage and the phase set, the ink jet printer is ready for printing and the LEIBINGER-JET 2 begins the print procedure independently upon receipt of a print start signal. The touch field <time/date set-up>(153) enables the import of date and time. The “entry level”... -
Page 113: Monitoring Functions (Control Functions)
With the touch fields <print go control> (157) and <stroke go control> (158) the functions can be activated or deactivated. At the same time the current status “OFF” or “ON” is shown in the fields. [E31] Release 3.00 Leibinger-Jet 2 se... -
Page 114: Encoder
“normal” and “extra” are available for selection. In the “extra” mode the print width is doubly wide. Only possible with the “without encoder” setting. Observation: In the “normal width” mode the device works at a rapid stroke rate, with “extra width” (extra wide) at a lower stroke rate. Release 3.00 Leibinger-Jet 2 se... -
Page 115: Job Change
“external job change” is activated in the single jobs. (This is necessary that no undefined job can be selected by switching over the inputs and that in every job the function “external job change” is already activated). Release 3.00 Leibinger-Jet 2 se... - Page 116 Seljob 6 Seljob 5 Seljob 4 Seljob 3 Seljob 2 Seljob 1 Seljob 0 … … 0 = Optocouppler not activated 1 = Optocouppler activated For further information about the connection and the pin numbers, please see group12 chapter Interface layout plan. Release 3.00 Leibinger-Jet 2 se...
-
Page 117: Service/Test- And Diagnosis Functions
In this menu the control of the oscillator voltage regulation can be read. Its presentation is made in the form of a summary graph. Settings and alterations! This work must only be carried out by Leibinger service technicians! Figure 94 The touch field <curve>... -
Page 118: Motor Test
The touch field <motortest> (173) enables the manual setting of the gutter. [E16] [E37] By means of tapping on <motor step open> (174) or <motor step close> (175) the gutter motor is driven and the gutter moves forwards or backwards. Release 3.00 Leibinger-Jet 2 se... -
Page 119: Charging Voltage Test/Piezo Test
Oscillator voltage setting: issue of a constant oscillator voltage that serves reconciliation with the oscillation voltage booster (Poti TRM 1). Charging voltage setting: issue of a constant charging voltage for the adjustment of the charging voltage booster (Offset TRM 2, boost TRM3). Release 3.00 Leibinger-Jet 2 se... -
Page 120: Software Information
The function permanent bleed can be only activated if the device is working under the following conditions: ! the ink supply is switched on ! the head cover has been removed. Release 3.00 Leibinger-Jet 2 se... -
Page 121: Hydraulic Test & Parameters
(values on the addition of ink and solvent) are shown. Before exiting with <ESCAPE> it is imperative that the regulation again be switched on. Incorrect operation can lead to major disturbances to the device! Release 3.00 Leibinger-Jet 2 se... - Page 122 (e.g. in case of service) to simplify the communication with the dealer or the LEIBINGER Service – Hotline. The change happens by pressing the touch field <english> (201). You can go back to the standard- menu language with the touch field (200).
-
Page 123: Touch Screen Calibration
The <Intervall time> mode (202) enables the entry of start and limit times at which the LEIBINGER-JET 2 switches itself on or off automatically for circulation of the ink (e.g.: at 10.25 hours the device switches on / at 10.40 hours the device switches off). -
Page 124: Service Interval
! the working hours since the last inspection (253) ! the total amount of working hours (254) [E64] of the device ! the date of the last inspection (255) The touch field <ESCAPE> (256) ends the menu. Release 3.00 Leibinger-Jet 2 se... -
Page 125: Trouble Shooting
The error is acknowledged by means of touching the touch field <error notification> (status line). Figure 103 Status line with error notifications (specimen illustration) [E1] Release 3.00 Leibinger-Jet 2 se... -
Page 126: Error Messages
Clean, if necessary“ Charging electrode dirty/defective. Please Check charging electrode and clean or clean or replace. replace. Display message:„charge elect. Dirty please check charge electrode for dirt accumulation, clean, if necessary“ Release 3.00 Leibinger-Jet 2 se... - Page 127 Refill ink. Ink will soon be empty! Please refill. Display message:„Ink tank is low level please refill ink“ Solvent will soon be empty! Please refill. Refill solvent. Display message:„Solvent tank is low level please refill solvent“ Release 3.00 Leibinger-Jet 2 se...
- Page 128 Servicing! Display message:„faulty visco-measurement please check visco- pump and –meter or call our perfect Leibinger service“ Ink conveying defective. Please check Disconnect device from the mains supply! main pump, pressure tank and their Check the main pump, the pressure tank and connections.
-
Page 129: Other Causes Of Errors
! Head cover of the print head not assembled or incorrectly assembled ! Product sensor not connected or set incorrectly ! Basic settings incorrect ! Value incorrectly set -menu level <E43> Suction pump achieving no power ! Cleaning necessary, chapter Miscellaneous cleaning work Release 3.00 Leibinger-Jet 2 se... -
Page 130: Equipping/Maintenance
If no acknowledge-ment of the refill alarm is made within 10 minutes, the LEIBINGER-JET 2 will stop the production and close the jet and the device will switch off. - Page 131 Depending on the ink, ambient temperature and humidity the consumption of LEIBINGER solvent can be between 20-100 ml/8 hours. With higher temperatures in shift operation LEIBINGER solvent should therefore be checked or refilled daily.
-
Page 132: Guarantee
At this point we wish to make explicit reference to the fact that it is only when using solvent and ink from Paul Leibinger GmbH & Co. KG that the optimum operating characteristics can be achieved. In the event of use of other inks and solvents all guarantee entitlements shall cease to apply. -
Page 133: Nozzle Sealing
Risk of injury! Ink escapes from the head aperture. Spraying of ink into the eyes can cause blindness. Eye protection is necessary! This work must only be carried out by trained personnel or by Leibinger service technicians! Release 3.00 Leibinger-Jet 2 se... - Page 134 ! Swivel deflector unit upwards and secure with toggle lever. ! Open the nozzle (move gutter forwards). ! The nozzle plate can be removed following undoing of the knurled screw and swivelling away of the bar. Release 3.00 Leibinger-Jet 2 se...
-
Page 135: Annual Servicing Work
Equipping/maintenance Page 135 ! Cleaning of the nozzle only with LEIBINGER solvent against and in the direction of the current or with the help of an ultrasound bath and subsequent blowing out with compressed air. Further information on this subject area can be found in the chapter Cleaning. -
Page 136: Filter Replacement And Ink Change
Manner of procedure: ! Place the LEIBINGER- JET 2 in operating mode “Nozzle closed” (1) and “Ink switch on” (2). ! Deactivate the regulation (3) in the menu level <E29> (main menu ! service/test/system parameter ! service/test &... - Page 137 Group 9 Equipping/maintenance Page 137 ! The LEIBINGER- JET 2 is without pressure and must be disconnected from the mains supply. Remove mains plug! Figure 106 Unscrew only the continuous allan screws! ! Undo the 2 Allan screws and remove the entire pressure tank if the tube connections allow this (picture sequence 1).
- Page 138 ! Again insert the pressure tank and attach the tube connections. ! The further steps are carried out in an empty condition as with the initial commissioning. Further information can be found in the chapter Start up! Release 3.00 Leibinger-Jet 2 se...
-
Page 139: Other Servicing Work
In order to achieve a better contrast in poor light it is helpful if you first of all clean the gutter and the print head chassis with Leibinger solvent and hold white paper behind or below the gutter. Further information on this subject area can be found in the chapter Cleaning. -
Page 140: Replacement Of The Main Pump
Danger of serious damage through burns, skin irriation and poisoning! Risk of injury! Spraying of ink into the eyes can cause blindness. Prior to the opening of the device eye protection must be put on! Release 3.00 Leibinger-Jet 2 se... - Page 141 Leibinger service technicians! Figure 108 Main pump (54-002-001 S) ! Place the LEIBINGER-JET 2 in the operating mode “Nozzle closed” (1) and “Ink switch on” (2). ! Deactivate the regulation (3) in the menu level <E29>(main menu ! service/ test/system parameter ! service/test & diagnostics ! hydraulic test & parameter).
-
Page 142: Replacement Of The Battery And Fuse
Safety instructions as well as the Disposal instructions of the battery manufacturer are observed! Figure 109 1 – Battery, lithium, 3.2 VDC (54-003 032 KA) 2 – Fuse 1,6 H (54-003 339 KA) Release 3.00 Leibinger-Jet 2 se... -
Page 143: Servicing Work With More Difficult Operating Conditions
The time must however be estimated on the basis of experience values. This applies above all for: ! Changing the ink (high water content or destruction of the binding agent) ! Replacement of the filter insert Release 3.00 Leibinger-Jet 2 se... -
Page 144: Cleaning
Leibinger solvent (corresponding to the Leibinger ink). This is achieved through applying the Leibinger solvent to fluff-free paper with the spray bottle and wiping off the parts to be cleaned with this. Direct spraying off of the print head with solvent should only be carried out with very major dirt and should be limited to the front part of the print head. -
Page 145: Cleaning The Deflector Unit And Gutter
During the closing movement of the print head your fingers could get caught between deflector unit or nozzle plate and gutter or during the opening movement between housing and gutter. Keep your hands outside of the danger area! Release 3.00 Leibinger-Jet 2 se... -
Page 146: Weekly Cleaning Work
LEIBINGER solvent. After cleaning dry the deflector unit (e.g. with compressed air). Subsequently the deflector unit can again be swivelled carefully downwards following release of the toggle lever. -
Page 147: Other Cleaning Work
Eye protection is necessary! Risk of injury! Upon contact the contents causes skin irritation. Protective equipment is necessary! This work must only be carried out by trained personnel or by Leibinger service technicians! Release 3.00 Leibinger-Jet 2 se... - Page 148 (wooden only). Caution: Risk of damage! For this the nozzle is first of all rinsed out with LEIBINGER solvent and the jet is blown dry from both directions with compressed air. Thereafter you move to the nozzle stone (2) from both sides with a tooth-pick (wooden only). By means of light pressure and turning the ink remains are detached from the nozzle stone.
-
Page 149: Cleaning The Suction Pump
The suction pump works with an Figure 113 underpressure > 0.3 bar. If this is not achieved, dirtying of the valve reeds or damage to the working membrane can be present. Suction pump (54-002 002 S) Release 3.00 Leibinger-Jet 2 se... - Page 150 ! Press the button “pressureless” (4) in the menu level <E29> and wait for a while until the values for the “membrane” and “pressure” (5) moving towards ~“0“. ! The LEIBINGER- JET 2 is now without pressure and must be disconnected from the mains supply. Remove mains plug! ! Detach tube connections and connection cable and dismantle suction pump.
-
Page 151: Further Maintenance Measures (Service Intervals)
Page 151 9.5 Further maintenance measures (Service intervals) The LEIBINGER-JET 2 has to be subjected additional to the normal maintenance- and service works to an inspection in regular intervals by authorized qualified personnel to guarantee a safe and trouble-free operation. -
Page 152: Taking Out Of Operation
The device must be cleaned of dirt, ink residue etc. as described in the chapter Cleaning. 9.7 Dismantling/disposal The LEIBINGER-JET 2 has been developed and built with materials that ensure problem- free dismantling and disposal. When dismantling, the information in the chapter Taking out of operation as well as the respective country specific disposal regulations (e.g. -
Page 153: Replacement Parts
Group 10 Replacement parts Page 153 10. Replacement parts The construction condition list attached to each LEIBINGER-JET 2 is authoritative for the most important components and structural components used. Whenever ordering replacement parts please quote the series number of the device. -
Page 154: Replacement Parts Print Head Sk2
Set of hexagon socket screw keys, 4mm and 5 mm 54-002 360 SA Set of Screwdrivers, solvent resistant 54-002 361 SA consisting of: PH 1 x 60 cross, PH 00 x 40 cross, PH 3.0 x 50 blade Release 3.00 Leibinger-Jet 2 se... -
Page 155: Cleaning/Servicing Accessories
54-000 120 SC Adjusting slide cpl. 2-axis (XY) LJ2 with quick separation and precise 54-000 903 SA adjust Universal bottom stand 54-000 605 SB PC# LJ2 connection cable 54-002 295 SA Moveable underframe 54-002 601 KA Release 3.00 Leibinger-Jet 2 se... -
Page 156: Data Entry Devices
Win Jet data entry software for windows® 95/98/NT 4.0/ 2000/XP- On request Professional LJ-Flash Software for Windows® On request Personal Computer with data entry software On request Laptop with data entry software On request Industrial PC, 19" version On request Release 3.00 Leibinger-Jet 2 se... -
Page 157: Consumables
79000-00006 77001-00007 Ink, white, Rubber, PVC, ABS, PA. Good contrast white MEK-free, PI, free pigmented white MEK-free 79000-00008 77001-00001 Ink, white, Ketone PVC, ABS, CAB, PVdC, Good contrast white ketone, PI, metals pigmented white contrast Release 3.00 Leibinger-Jet 2 se... -
Page 158: Appendix
Group 12 Appendix Page 158 12. Appendix 12.1 Hydraulics diagram (modular mimic display) Figure 115 Release 3.00 Leibinger-Jet 2 se... -
Page 159: Interface Layout Plan
Group 12 Appendix Page 159 12.2 Interface layout plan Figure 116 Interface layout plan part no. 1 Release 3.00 Leibinger-Jet 2 se... - Page 160 Group 12 Appendix Page 160 Figure 117 Interface layout plan part no. 2 Release 3.00 Leibinger-Jet 2 se...
-
Page 161: Calculation Of The Print Speed
The maximum and in particular the minimum character height depend to a very great extent on the ink used, the material and the surface. Release 3.00 Leibinger-Jet 2 se... - Page 162 43,894 0,732 0,551 2 / 24 Dot 0,4032 28,531 0,476 0,848 0,4032 88,886 1,481 0,272 0,4032 85,594 1,427 0,283 2 / 24 Dot 0,4032 27,434 0,457 0,882 2 / 24 Dot 0,4032 28,531 0,476 0,848 Release 3.00 Leibinger-Jet 2 se...
- Page 163 G 24 0,3432 27,434 0,457 0,751 G 24 0,3432 26,337 0,439 0,782 G 24 0,3432 39,505 0,658 0,521 G 24 0,3432 26,337 0,439 0,782 G 24 0,3432 27,434 0,457 0,751 G 24 0,3432 26,337 0,439 0,782 Release 3.00 Leibinger-Jet 2 se...
-
Page 164: Fonts
Group 12 Appendix Page 164 12.4 Fonts Release 3.00 Leibinger-Jet 2 se... - Page 165 Group 12 Appendix Page 165 Release 3.00 Leibinger-Jet 2 se...
-
Page 166: List Of Graphics
Group 12 Appendix Page 166 12.5 List of graphics (standard) Release 3.00 Leibinger-Jet 2 se... -
Page 167: Technical Drawings
Group 12 Appendix Page 167 12.6 Technical drawings Figure 119 Print head SK2 Release 3.00 Leibinger-Jet 2 se... - Page 168 Group 12 Appendix Page 168 Figure 120 Cabinet LJ 2 Release 3.00 Leibinger-Jet 2 se...
-
Page 169: List Of Keywords/Index
..........75 cleaning set ..........155 drawings ..........167 components..........43 drop charging .........44 conductor plate........60 drop creation ..........44 connection values........28 drop deflection........45 construction ..........43 drop production unit........69 consumables ........23, 157 consumption .........131 control...........121 control functions ........113 Release 3.00 Leibinger-Jet 2 se... - Page 170 ...........89 opening job..........86 storing jobs..........89 job change..........115 general reset ..........51 graphic list ..........166 graphics editor........79 graphics entry.........78 language..........122 graphics selection......78, 79 LCD touch display ........59 guarantee ........12, 132 leak............67 gutter ............70 handling..........25 hardware reset ........52 Release 3.00 Leibinger-Jet 2 se...
- Page 171 43 ........122 menu level 44 ........104 menu level 46 .........89 menu level 47 .........88 menu level 49 .........88 menu level 5 .......86, 87, 88 menu level 50 ......78, 80, 109 menu level 51 .........73 Release 3.00 Leibinger-Jet 2 se...
- Page 172 ......113 safety instructions......12, 14 printing with external job selection ..115 safety sticker ..........21 service functions ..117, 120, 121, 123, scope of risks .........14 sensor queries........100 service ..........132 adjusting the ink jet ......139 Release 3.00 Leibinger-Jet 2 se...
- Page 173 1or 2 lines free position .......72 jobs menue..........86 bar hight ..........85 list jobs ..........89 barcode ..........72 load job..........86 Barcode..........84 barcode parameter......85 bleed ..........121 bold .............76 bs ..........104, 112 change masteruser ......93 change superuser ....91, 93, 96 Release 3.00 Leibinger-Jet 2 se...
- Page 174 115 viscosity control ........66 repeat count ........108 viscosity pump........66 replacements set-up......105 request ..........48 reset ..........108 reset count. 1 ........107 weights ...........28 reset count. 2 ........107 WYSIWYG display .........76 ret ..........104, 112 RET ..........73, 89 Release 3.00 Leibinger-Jet 2 se...
-
Page 175: List Of Illustrations
Figure 32 – Suction pump Figure 33 – Viscometer Figure 34 – Viscosity pump Figure 35 – Leak detection Figure 36 – Print head Figure 37 – Drop production with oscillator Figure 38 – Deflector unit Release 3.00 Leibinger-Jet 2 se... - Page 176 Figure 74 – Menu level 4 (flight time) Figure 75 – Menu level 4 (print go/print go gate) Figure 76 – Menu level 4 (meter go function) Figure 77 – Menu level 4, 8, 1 (meter go settings) Release 3.00 Leibinger-Jet 2 se...
- Page 177 Figure 111 – Spindle of the nozzle seal Figure 112 – Nozzle sealing Figure 113 – Suction pump Figure 114 – Service interval message Figure 115 – Hydraulics diagram Figure 116 – Interface-Layout-Plan Part No. 1 Release 3.00 Leibinger-Jet 2 se...
- Page 178 Group 12 Appendix Page 178 Figure 117 – Interface-Layout-Plan Part No. 2 Figure 118 – Stroke gap Figure 119 – Technical drawing print head SK2 Figure 120 – Technical drawing cabinet LJ2 Release 3.00 Leibinger-Jet 2 se...
Need help?
Do you have a question about the Jet 2 and is the answer not in the manual?
Questions and answers