Warnings And Cares; General Precautionary Measures; Information About The Machine; Identification Data - Gaggia Concetto Operating Instructions Manual

Gaggia concetto: operating instruction
Hide thumbs Also See for Concetto:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 28

6 - WARNINGS AND CARES

• In routine maintenance, never use detergents, diluents, solvents,
etc...
• Cleaning has to be limited at parts of the machine being not
powered and must be carried out with mild and biodegradable
products. Moreover the main switch or the all-pole switch have
to be on the "O"(OFF) position, or the plug has to be discon-
nected from the power point.
• The routine maintenance has to be carried out only by compe-
tent or adequately trained personnel, having the necessary
psychophysical requirements, in the whole respect of the instruc-
tions mentioned below and according to the current Safety and
Health Regulations.
• It is strictly forbidden to place and/or leave on the machine
tools or anything which could potentially be prejudicial to the
people safety and to the integrity of the machine.
• Changing and adjustments (even if slight) as well as the use of
non original spare parts, release the Manufacturer from any
responsibility for any type of damage and implies the cancella-
tion of any warranty right.
• Use only drinking water.
• The milk to be used for the CAPPUCCINATORE must be put in a
fridge at a temperature not over 4 C; do not leave it outside the
fridge for more than 30 minutes.
• If the CAPPUCCINATORE is not used for more than an hour,
carry out a cleaning cycle of the spouts before re-using.
To clean the spouts:
- immerse the milk supply tube in a container of water;
- press the milk key
;
- wait until the water has been dispensed.
PLEASE NOTE: Do not use hot water.
7 - GENERAL PRECAUTIONARY
MEASURES
• Before operating the machine, be previously sure not to have
any doubt about the contents of this manual. Non respecting the
rules explained in it releases the Manufacturer from any
responsibility for any type of injury to persons and/or damage
to things.
• Keep this brochure for any further reference.
• Previously verify (in case of a new installation), the respect of the
minimal regulations of safety, positioning and machine operating
conditions, checking the environment conditions (temperature,
humidity, light) and the suitability of the place of operation.
• Any damage to the electric power cord requires the intervention
of the Technical Authorized Customer Service or of the
maintenance technician.
• Do not use the machine on the outside.
• In case of bad functioning, always ask for the intervention of the
maintenance technician.
• Do not use water jets to clean the machine.
CONCETTO
8 - INFORMATION ABOUT
THE MACHINE
8.1

Identification data

In the (A) plate the following identification data of the machine are
mentioned:
• Manufacturer and
• model
• serial number
• manufacturing year
• mains electric voltage (V) and frequency (Hz)
• electrical power consumption (W)
• number of phases of the electric line (PH)
• pressure allowed in the water network (MPa)
NOTE - In case of any request to the Authorized Customer
Service Centers, model and serial number must be
specified.
8.2

Technical characteristics

Mains voltage .......................................... 230V/400V 2N
A-weighted sound pressur level is ...................... below 70 dB
Length of the power cord .................................... 1,500 mm
Installed power
Mod. LUXE ....................................................... 3,250 W
Mod. COFFEE .................................................. 1,400 W
Mod. CAPPUCCINO ......................................... 3,250 W
Water pressure ............................... 0.1 0.8 MPa (1 8 bar)
Weight .................................................................. kg 60
Bean hopper capacity. ................................................ kg 2
NOTE - The machines can be programmed for any type of
dosing. Most electric parts are powered by 24 Vdc.
8.3

Overall dimensions

P
F. 2
28/120
marking
h
L
L
P
470
550
675
English
h

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents