Related Manuals for Savoy House M2009 Series
Summary of Contents for Savoy House M2009 Series
- Page 1 CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODELS: M2009XX FAN RATING AC 120V. 60Hz UL LISTED MODEL : AC-552...
-
Page 2: Tools And Materials Required
1. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 2. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: a. Set of blades assembly (5) b. -
Page 3: Safety Rules
3. SAFETY RULES 1. To reduce the risk of electric shock, insure Do not operate reversing switch while fan blades are in motion. Fan must be turned electricity has been turned off at the circuit breaker or fuse box before off and blades stopped before reversing beginning. -
Page 4: Mounting Options
4. MOUNTING OPTIONS If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building Outlet box structure. Use appropriate fasteners and building materials. -
Page 5: Hanging The Fan
5. HANGING THE FAN REMEMBER to turn off the power. Follow the steps below to hang your fan properly: CUL Listed electrical box 120V Wires Step 1. Pass the 120-volt supply wires Hanger bracket through the center hole in the ceiling hanger Hook bracket as shown in Fig. -
Page 6: Make The Electric Connections
6. MAKE THE ELECTRIC CONNECTIONS POWER LINES 120V GREEN GROUND Remember to disconnect the power. Follow the steps below to connect the fan to WIRING your household wiring. Use the wire connecting nuts supplied with your fan. GROUND TO Secure the connectors with electrical tape. MOUNTING BRACKET Make sure there are no loose strands or... -
Page 7: Finishing The Installation
7. FINISHING THE INSTALLATION Step 1. Tuck connections neatly into ceiling Outlet box outlet box. Hanger Step 2. Secure the canopy to the hanger bracket bracket with the four canopy mounting screw provided. (Fig. 11) Screws WARNING: Make sure tab at bottom of Canopy hanger bracket is properly seated in groove of hanger ball before attaching canopy to... - Page 8 9. INSTALLATING THE MOUNTING PLATE 1. Remove the 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) 2. Place the key holes on the mounting plate over the 2 screws previously loosened from the mounting ring, turn mounting plate until it locks in place at the narrow section of the key holes.
-
Page 9: Installing The Light Kit Assembly
11. INSTALLING THE LIGHT KIT ASSEMBLY NOTE: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. Step 1. Remove the 3 screws from the mounting plate. Step 2. While holding the Light kit assembly under your fan, snap together the wire connection plug. -
Page 10: Operating Your Fan
13. OPERATING YOUR FAN Turn on the power and check the operation of your fan. The pull chain controls the fan speed as follows: 1 pull- High, 2 pulls-Medium, 3 pulls- Low, and 4 pulls-Off. Light pull chain it controls the light in "ON" or "OFF". -
Page 11: Care Of Your Fan
14. CARE OF YOUR FAN Here are some suggestions to help you maintain your fan 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. -
Page 12: Troubleshooting
15. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. Fan sounds noisy. 1.
Need help?
Do you have a question about the M2009 Series and is the answer not in the manual?
Questions and answers