BioTel Heart ePatch Quick Start Manual

T
STEP 2: ATTACH SENSOR TO THE PATCH
Attach sensor to the patch
ART
ation
/shave
eded)
Clean skin
n
If necessary shave chest area where
If necessary shave chest area where
skin
patch is to be applied. Clean area
patch is to be applied. Clean area
st area where Snap sensor into the patch. Press
with soap and water. Pat dry. Gently
where Snap sensor into the patch. Press
with soap and water. Pat dry. Gently
Clean area all four sides to ensure sensor is
Snap sensor into the patch. Press all four
area scrub skin with abrasion pad. all four sides to ensure sensor is
scrub skin with abrasion pad.
sides to ensure sensor is securely connected
Pat dry. Gently securely connected to the patch.
Gently securely connected to the patch.
to the patch. You will hear several clicks.
on pad. You will hear several clicks.
. You will hear several clicks.
Apply patch to your skin
STEP 4: APPLY PATCH TO YOUR SKIN
our skin
RIGHT
RIGHT
n Remove cover paper
LEFT
RIGHT
FT
RIGHT
Apply patch to chest on a slight
Apply patch to chest on a slight
Apply patch to chest on a slight angle as
on a slight
Gently peel off the white cover
shown in the illustration above. Press all sides
angle as shown in the illustration
angle as shown in the illustration
e illustration
paper of the patch with the pull
of the patch so it will adhere to your skin.
ght
Gently peel off the white cover
above. Press all sides of the patch
above. Press all sides of the patch
of the patch
tab in the center.
ation
paper of the patch with the pull
STOP: Wait 1 minute before proceeding to
so it will adhere to your skin.
so it will adhere to your skin.
ur skin.
Step 5.
patch
tab in the center.
STOP: Wait 1 minute before
STOP: Wait 1 minute before
before
proceeding to Step 5.
proceeding to Step 5.
STEP 1:
STEP 1:
Skin preparation
Skin preparation
STEP 2:
Wash/shave
STEP 2:
(if needed) Wash/shave
Attach sensor to the patch
(if needed)
Clean skin
Clean skin
Scrub skin
Scrub skin
STEP 4:
STEP 4:
Apply patch to your skin
STEP 5:
STEP 5:
Remove cover paper
If needed, shave chest area so that it is clear
of any hair. Clean area with soap and water.
Pat dry. Gently scrub skin with abrasion pad.
Attach sensor to the patch
Snap sensor into the patch. Press
Snap sensor into the patch. Press
all four sides to ensure sensor is
all four sides to ensure sensor is
Remove the clear plastic backing
securely connected to the patch.
Remove the clear plastic backing
securely connected to the patch.
to expose the adhesive part of the
Remove the clear plastic backing to expose
to expose the adhesive part of the You will hear several clicks.
You will hear several clicks.
the adhesive part of the patch. Do not touch
patch.
patch.
the adhesive.
Do not touch the adhesive.
Do not touch the adhesive.
LEFT
LEFT RIGHT
RIGHT
LEFT
LEFT
Gently peel off the white cover
Gently peel off the white cover
Gently peel off the white cover paper of
the patch with the pull tab in the center.
paper of the patch with the pull
paper of the patch with the pull
tab in the center.
tab in the center.
™
QUICK START GUIDE
STEP 1: SKIN PREPARATION
Shave:
(if needed)
Clean skin
Scrub skin
STEP 2:
STEP 2:
Attach sensor to the patch
STEP 3:
STEP 3:
STEP 3: REMOVE PATCH BACKING
Remove patch backing
Remove patch backing
STEP 5:
STEP 5:
Remove cover paper
STEP 5: REMOVE COVER PAPER Remove cover paper
Copyright © 2019. All rights reserved
R
Remove
Remov
to expos
to expo
patch.
patch.
Do not to
Do not
LEFT
LEFT
®
Co
R