Aiwa CDC-X927M YUC Operating Instructions Manual

Aiwa CDC-X927M YUC Operating Instructions Manual

Stereo car cd receiver
Hide thumbs Also See for CDC-X927M YUC:

Advertisement

OPERATING INSTRUCTIONS

MANUAL DE INSTRUCCIONES
MODE D'EMPLOI
CDC-X927M
STEREO CAR CD RECEIVER
RADIO-TOCADISCOS DE CD ESTEREOFONICO PARA
AUTOMOVIL
OWNER'S RECORD
For your convenience, record the model number and
serial number (you will find them on the bottom side of
your set) in the space provided below. Please refer to
them when you contact your AIWA dealer in case of
difficulty.
Model No. CDC-X927M
Serial No.
YUC
ENGLISH
ESPAÑOL
FRANÇAIS
8C-KC4-901-01
020131ATM-OX

Advertisement

Table of Contents
loading

Summary of Contents for Aiwa CDC-X927M YUC

  • Page 1: Operating Instructions

    For your convenience, record the model number and serial number (you will find them on the bottom side of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty. Model No. CDC-X927M Serial No.
  • Page 2: Table Of Contents

    PRECAUTIONS • Use only in a 12-volt DC negative-ground electrical system. • Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit. • When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.
  • Page 3: Theft Protection

    THEFT PROTECTION (Retractable Front Panel) When your car’s ignition switch is turned off, the front panel will be retracted automatically as if there were no car audio in the console. When the ignition switch is set to ACC or ON position, the front panel will appear automatically.
  • Page 4: Radio Operation

    Restoring the factory settings Turn off the unit. Press and hold DISP until “LEVEL --” appears on the display. Note You can restore the factory settings only for VOL, BASS, TRE, BAL, FAD, H-BASS, DSSA and BBE as well as aligned source volume levels.
  • Page 5: Cd Player Operation

    Presetting stations automatically (Auto Memory) Press BAND repeatedly to select the desired band (F1, F2, F3, A1 or A2). Press and hold PS/A.ME until automatic presetting starts. “A MEM” appears on the display. The unit automatically stores up to 6 stations for each band.
  • Page 6: Auxiliary Equipment

    Notes • When you play a CD that is already inserted, CD play starts at the point where it stopped the previous time. A newly inserted CD starts from the first track. • A CD-R or CD-RW may take some time to start playing back, but this is not a malfunction.
  • Page 7: Card Remote Control

    CARD REMOTE CONTROL Names of parts BAND TAPE CD-CH SKIP TUNING / DISC DOWN VOLUME 1 BAND button 2 TAPE button (This button is not available with this unit.) 3 CD button 4 CD-CH button (CD changer only) 5 SKIP f/REW button 6 SKIP g/FF button 7 PS (preset) button 8 TUNING/DISC UP/DOWN buttons...
  • Page 8: Cd Changer Operation

    CD CHANGER OPERATION Playing a CD You can play CDs from a connected AIWA CD Changer. For detailed information on installing a CD Changer, refer to the Installation and Connection manual supplied with the CD Changer. REP1 DISC Press SRC repeatedly to display “CD-CH.”...
  • Page 9: Maintenance

    Reset button If a CD does not operate properly, press the reset button with a pointed object such as a pencil, etc. Note that all your settings will be erased if this button is pressed. MAINTENANCE Cleaning the front panel Wipe the surface with a soft, dry cloth.
  • Page 10 Printed in Indonesia...

Table of Contents