Installation Procedure; Gas Connection - Electrolux EHG8321BC Installation & User Manual

Installation procedure

・ Before installing the appliance, check that the location provides
the required clearances from combustible materials and check
if necessary to provide protection to adjacent surfaces as
required by the regulation. Make provision for the gas supply to
be connected to the location.
・ Cut the opening in the bench top by the cardboard - template
given in the hob packing or to the dimensions shown in Fig 7.
・ Remove the hob from the carton.
・ Install the hob in the cut-out (Fig 7)
・ Connect gas supply to inlet of hob. Turn the gas on and check
for leaks using soap solution and brush around all the joints
and connection.
・ Test the appliance; depress the control knob and turn to full
flame setting to activate the electric igniter. The burner will
ignite. Adjust control knob to the desired setting. On initial
usage you may have to repeat this ignition function several
times (to allow air to be purged from the gas supply system).
No adjustment should be necessary. If any problem occur,
refer to the servicing instructions or the fault finding chart.
・ Ensure the manual is left with the user. If any of the above
procedures do not produce satisfactory results, the agent
service department should be consulted for more specialized
assistance.
・ This gas hob has been tested for operating on town gas
pressure up to 31 mbar
・ Gas connection
・ The supply hose must be visible for its entire length (max.
one meter) and must be secured with a hose clamp X (Fig
8). The sealing washer must be fitted.
IMPORTANT SAFETY INSTRUCTION:
Upon completion of gas installation connections, it is
compulsory to check for gas leakage at the joint. (Soap
test)
Soap test procedure
・Turn the burner controls off and turn on the gas supply.
・Apply soapy solution to each joint. (Figure 8)
・Formation of bubbles indicates leakage and must be tightened.
・Repeat soap test
Flexi Installation Cut Out
・ The smaller burner (lower) box of this cooktop combined
with the extended glass overhang, and flexible bracket
makes installation into existing counter cut-outs easy
without additional modification.
・ For replacement purchase, ensure cutout size fall within
the given dimension for the desired hob.
・ Gas hobs should be secured properly with the flexible
brackets provided to prevent it from moving in Fig 7.
Cut-out Dimension
Model
EHG8321BC Width (630-765)*Depth(350-465) R50
EHG8241GE Width (630-765)*Depth(350-465) R50
EHG8250BC Width (630-765)*Depth(350-465) R50
EHG8251BC Width (630-765)*Depth(350-465) R50
EHG8260GE Width (630-765)*Depth(350-465) R50
EHG8260BC Width (630-765)*Depth(350-465) R50
EHG9231BC Width (700-865)*Depth(405-480) R50
EHG9331BC Width (700-865)*Depth(405-480) R50
EHG9251BC Width (700-865)*Depth(405-480) R50
EHG9350BC Width (700-865)*Depth(405-480) R50
EHG9351BC Width (700-865)*Depth(405-480) R50
EHG9261BC Width (700-865)*Depth(405-480) R50
EHG9361BC Width (700-865)*Depth(405-480) R50
EHG8250BCP Width (630-765)*Depth(350-465) R50
EHG9350BCP Width (700-865)*Depth(405-480) R50
F L E X I B L E B R A C K E T
Cooktop (glass/stainless steel)
Burner (lower)
box
Adjust the bracket
Fig.7 (in mm)
Bench cut-out size viewed from front of bench, i.e. control panel at front.
If clearance between side/back walls and periphery of the burner
is less than 200mm, the walls must be protected with
non-combustible material. The protection must extend a
minimum distance of 450mm above the burner. Horizontal
surfaces less than 750mm vertically above the hob must also be
protected.
installation instructions 8
W I D T H
Countertop
4 x R 5 0