Electrical Safety - Black & Decker HG2000 Instruction Manual

ENGLISH
work area that could or may be contaminated by lead. Lead
based paints should only be removed by a professional
and should not be removed using a heat gun.
• When removing paints you should ensure that your work
area is enclosed. It is advisable to wear a dust mask.
• Do not burn the paint. Keep the nozzle at least 25mm (1")
from the surface as this keeps the temperature below the re
quired 450°C. If you are scraping from a vertical position then
you should scrape downwards to prevent the paint from falling
back into the heat gun and burning. Dispose of all paint debris
safely and ensure that the work area is thoroughly cleaned
after completing the job.
• Do not use in a damp atmosphere or where flammable
gases may be present or use near combustible materials.
Spaces behind boards, ceilings and floors and wall cavities in
timber frame constructed houses can contain flam mable
materials. Check before using the heat gun.
• Allow the tool to cool fully before storing.
• Ensure adequate ventilation when using heat guns as
toxic fumes may be produced.
• Do not use as a hairdryer! The air temperature is far higher
than a hairdryer.
• Do not obstruct either the air intake or nozzle outlet as
this may cause excessive heat build up resulting in
damage to the tool.
• Do not direct the hot air blast at other people.
• Do not touch the metal nozzle as it becomes very hot
during use and remains hot for up to 30 minutes after
use. Do not look down the nozzle while the unit is working
because of the high temperatures being produced.
• Do not allow paint to adhere to the nozzle or scraper as
it could ignite after a time.
• Do not operate your heat gun whilst it is hanging by the
hanging hook.
• A fire may arise if the appliance is not used with care.
• Do not place the nozzle against anything while using or
immediately after use.
• Do not poke anything down the nozzle as it could give
you an electric shock.
Features (fig. A)
1. Switch
2. Heat control knob
3. Ventilation slots
4. Nozzle
Handling Your Heat Gun
Do not place your hand over the ventilation slots (3) or block these vents
in any way. This restricts the airflow through the element and causes
over heating.
Setting the temperature (fig. B)
• To increase the temperature setting, turn the heat control knob
(2) anti-clockwise.
• To reduce the temperature setting, turn the heat control knob
clockwise.
10
All manuals and user guides at all-guides.com
Operating Your Heat Gun (fig. C)
• To switch your heat gun on at the low temperature setting,
press the switch (1) to depress to position "I".
• To switch the tool on at the high temperature setting, set the
switch (1) to position "II".
• To switch the tool off, set the on/off switch (1) to position "0".
Note: Allow the element to heat up for a few seconds before
use. Initially, some smoke may emit from your heat gun. This
is normal and will soon cease.
Cooling Down
In use, the nozzle (4) of your heat gun becomes extremely hot.
Great care is necessary when cooling your heat gun after use.
Hands Free Use (fig. D)
This tool can also be used in stationary mode.
• Place the tool onto a firm and stable surface as shown.
• Always point your heat gun away from you.
• Secure the cable to prevent pulling your heat gun off the stand.
Do not touch the nozzle (4) and ensure that nothing is
dropped into the nozzle. Carefully switch off your heat gun
and then allow it to cool.
Paint Stripping
Your heat gun is designed to soften paint and lacquer enabling
it to be removed using a good quality hand scraper.
Proceed as follows: Direct the hot air onto the area to be
removed. When the paint softens, scrape firmly. Experiment
to establish the length of time necessary to apply the heat to
obtain optimum results. Scrape the softened paint immediately
or it will harden again.
Your heat gun is not suitable for stripping metal-framed
windows. This is because the heat from the heat gun is
conducted through the metal and can crack the glass. Scrape
with the grain of the wood wherever possible. Do not linger on
one spot for too long as the surface may char or ignite

Electrical safety

This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Warning: If the supply cord is damaged, it must be replaced
by the manufacturer, an authorized Black & Decker Service
Centre or an equally qualified person in order to avoid a
hazard. If the supply cord is replaced by an equally qualified
person, but not authorized by Black & Decker, the warranty
will lose effect.