Subscribe to Our Youtube Channel
Related Manuals for Ubiquiti ETHERMAGIC EM-S
Summary of Contents for Ubiquiti ETHERMAGIC EM-S
- Page 1 Gigabit+ Powerline System with 802.3af/at or 24V Passive PoE Models: EM-S, EM-EP, EM-KIT...
-
Page 2: Package Contents
Introduction Thank you for purchasing the Ubiquiti Networks® EtherMagic ™ Gigabit+ Powerline System with 802.3af/at or 24V Passive PoE. This Quick Start Guide is designed to guide you through the installation and also includes the warranty terms. Package Contents The package contents shown below will vary depending on... - Page 3 EtherMagic Overview An EtherMagic Gigabit+ network consists of one EtherMagic Switch and one or more EtherMagic EndPoints. Each EndPoint provides 802.3af/at or 24V passive PoE, and must be paired with a Switch to create a network. Up to 10 EtherMagic networks are supported on the same electrical circuit, and up to 32 EndPoints may be paired with a single Switch.
-
Page 4: Hardware Overview
Hardware Overview EtherMagic Switch Wall Plug Adapter LEDs LAN Port Reset Button Bottom View... - Page 5 Wall Plug Adapter Connects and mounts the Switch directly to the power outlet. The adapter can be removed and replaced with the included Power Cord for remote mounting. LAN Port Gigabit Ethernet port used to connect the Switch to the LAN and DHCP server. Reset Button To reset the Switch to factory defaults, press and hold the button for more than 10 seconds while the...
- Page 6 EtherMagic EndPoint Top View Reset Button PoE Port LEDs Wall Plug Adapter...
- Page 7 Reset Button To reset the EndPoint to factory defaults, press and hold the button for more than 10 seconds while the EndPoint is powered on. The EndPoint can also be reset using the EtherMagic app. PoE Port 48V 802.3af/at auto-sensing or 24V passive PoE Gigabit Ethernet port used to power and connect a device to the EtherMagic network.
-
Page 8: Hardware Installation
Hardware Installation For optimal performance, connect the EtherMagic Switch and EndPoints directly to wall outlets of the same electrical circuit. The Switch and EndPoints can be plugged in and mounted to the outlets directly using the Wall Plug Adapter, or plugged in using the optional Power Cord. - Page 9 2. (Optional) If using the Power Cord: a. Detach the Wall Plug Adapter from the Switch. b. Connect the Power Cord.
- Page 10 3. Plug the Switch directly to an electrical outlet. 4. Connect an Ethernet cable to the LAN port on the Switch. 5. Connect the other end of the Ethernet cable to your LAN (switch or router).
- Page 11 EtherMagic EndPoint Installation 1. Detach the Mounting Bracket from the EndPoint by sliding it in the direction shown below. 2. (Optional) If using the Power Cord: a. Detach the Wall Plug Adapter from the EndPoint.
- Page 12 b. Connect the Power Cord. 3. Plug the EndPoint directly to an electrical outlet.
- Page 13 4. Connect an Ethernet cable to the PoE port on the EndPoint. 5. Connect the other end of the Ethernet cable to your 24V/48V PoE device. Note: Non-PoE devices can be safely connected to the EndPoint for EtherMagic networking without PoE. The PoE port is set to 48V auto (802.3af/at) by default.
-
Page 14: Mounting (Optional)
Mounting (Optional) If the Power Cord is being used, the EtherMagic module may be mounted for added stability. 1. Place the Mounting Bracket at the desired location with the mounting tabs facing up, and mark the two holes. 2. Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included). - Page 15 EtherMagic App The EtherMagic app is used to set up and manage your EtherMagic devices, and also provides device and network statistics. The EtherMagic app is available as a free download from the Google Play store. ™ Note: The mobile device must be operating Android version 4.3 or above to support Bluetooth LE.
- Page 16 3. A list of new Switches will appear. Tap the Switch you would like to pair. 4. Switch Info will appear, displaying the Switch details.
- Page 17 5. Tap the EndPoint List tab, and then tap the EndPoint you would like to pair with the Switch. 6. Scroll down and tap Pair with Switch. 7. Upon successful pairing, the Link Quality of the connection will be displayed. Repeat steps 5 and 6 to pair additional Endpoints with the Switch.
-
Page 18: Specifications
Specifications EM-S, EM-EP Dimensions 107 x 62.4 x 31.7 mm (4.21 x 2.46 x 1.25") EM-S 107 x 62.4 x 40.7 mm (4.21 x 2.46 x 1.60") EM-EP Weight 135 g (4.76 oz) EM-S 190 g (6.70 oz) EM-EP Networking Interfaces (1) PLC, 1200 Mbps (1) RJ45, 10/100/1000 Mbps Management Interface... -
Page 19: Safety Notices
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. -
Page 20: Limited Warranty
Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation;... -
Page 21: Limitation Of Liability
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. - Page 22 Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
-
Page 23: Industry Canada
This radio transmitter (FCC: SWX-EMS) has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. - Page 24 Cet émetteur radio (IC: 6545A-EMS) a été approuvée par Industrie Canada pour l’exploitation avec l’antenne types énumérés ci-dessous avec le gain maximal admissible et requis l’impédance de l’antenne pour chaque type d’antenne indiqué. Types d’antenne non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué...
- Page 25 RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
- Page 26 Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Page 27: Declaration Of Conformity
[German] Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. Ελληνική Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις [Greek] βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 1995/5/ΕΚ. - Page 28 ©2016 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, and EtherMagic are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Google, Android, and Google Play are trademarks of Google Inc.
Need help?
Do you have a question about the ETHERMAGIC EM-S and is the answer not in the manual?
Questions and answers