Download  Print this page

4-Wire Connections; Installation - Frigidaire GLGT1142CS0 Installation Instructions Manual

Full size laundry center gas & electric
Hide thumbs
   

Advertisement

2. The laundry center is equipped with a three-prong
(grounding) plug for your protection against shock hazard
and should be plugged directly into a properly grounded
three-prong receptacle. Do not cut or remove the
grounding prong from the plug.
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
FOR A 3-WIRE SYSTEM
FOR A 3-WIRE SYSTEM
FOR A 3-WIRE SYSTEM
FOR A 3-WIRE SYSTEM
FOR A 3-WIRE SYSTEM
NON-CANADIAN ELECTRIC Laundry Center
1. Remove the screw securing the
terminal block access cover to the
rear panel and remove cover.
2. Install a U.L. approved strain relief
connector in the entry hole on the
back panel.
3. Insert a NEMA 10-30 Type SRDT,
U.L. approved power cord
through the strain relief.
4. Attach the power cord neutral (central wire) conductor to
the silver colored center terminal on the terminal block.
Tighten the screw securely.
5. Attach the remaining two power cord outer conductors to
the outer brass colored terminals on the terminal
block.Tighten both screws securely.
6. Tighten the screws securing the cord restraint against
the power cord.
7. Reinstall the terminal access cover.
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
FOR A 4-WIRE SYSTEM
FOR A 4-WIRE SYSTEM
FOR A 4-WIRE SYSTEM
FOR A 4-WIRE SYSTEM
FOR A 4-WIRE SYSTEM
NON-CANADIAN ELECTRIC Laundry Center
1. Remove the screw securing the
terminal block access cover to the
rear panel and remove cover.
2. Install a U.L. approved strain relief
connector in the entry hole on the
back panel.
3. Remove the neutral ground wire
from the green ground screw located above the termial
block.
4. Insert a NEMA 14-30 Type ST or SRDT, U.L. approved
power cord through the strain relief.
5. Attach the green power cord ground wire to the cabinet
with the green ground screw.
6. Attach the white (neutral) wire from the power cord and
the ground wire from the appliance harness to the silver-
colored center terminal on the terminal block. Tighten
the screw securely.
7. Attach the red and black wires from the power cord to
the outer brass-colored terminals on the terminal block.
Tighten both screws securely.
8. Tighten the screws securing the cord restraint firmly
against the power cord.
9. Reinstall the terminal block access cover.

INSTALLATION

1. Run some water from the hot and cold faucets to flush
the water lines and remove particles that might clog up
the water valve screens.
2. Check inlet hoses to ensure the rubber washers are
installed in each end.
3. Carefully connect the inlet hoses to the water valve (on
the left side of the washer cabinet), tighten by hand, then
tighten another 2/3 turn with pliers.
CAUTION
DO NOT CROSS THREAD OR
OVERTIGHTEN THESE CONNECTIONS.
4. Determine which water faucet is the HOT water faucet
and carefully connect the bottom inlet hose to the HOT
water faucet, tighten by hand, then tighten another 2/3
turn with pliers. Carefully connect the top inlet hose to
the COLD water faucet, tighten by hand, then tighten
another 2/3 turn with pliers.
CAUT ION
DO NOT CROSS THREAD OR
OVERTIGHTEN THESE CONNECTIONS. Turn the water on
and check for leaks at both connections.
5. Carefully move the laundry center to its final location.
6. To ensure the laundry center is level and solid on all four
legs, tilt the laundry center forward so the rear legs are
off the ground. Gently set the laundry center back down
to allow the rear legs to self adjust. Place a level on top
of the washer. Check it side to side, then front to back.
Screw the front leveling legs up or down to ensure the
laundry center is resting solid on all four legs (no rocking
of the laundry center should exist).
NOTE: Keep the leg extension at a minimum to prevent
excessive vibration.
7

Advertisement

Table of Contents
loading

  Related Manuals for Frigidaire GLGT1142CS0