Page 1
FAVORIT 40660 i Dishwasher User Instructions...
Page 2
In the event of a malfunction, these operating instructions contain information on how to rectify faults yourself, see the "What to do, if..." section. If these instructions are insufficient, please contact your AEG Service Force Centre. In this respect please read the chapter "Service & Spare Parts".
OPERATING INSTRUCTIONS Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. Neverthe- less, as a manufacturer we consider it our obligation to make you aware of the following safety information: Installation, Connection and Placing into Operation •...
• If the mains lead is damaged, or is to be replaced for a longer lead, the cable (obtainable from AEG Service Force) must be replaced by a service engineer authorised by AEG. • Never unplug the appliance by pulling on the cable, always pull the plug.
• In the event of a fault, first close the tap, then switch off the appli- ance and unplug it from the mains. If the appliance is permanently wired to the mains: remove the fuse. Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly.
Operating Instructions Appliance Features and Control Panel Top Spray Nozzle Rubber Seal for Connecting the Water Feed to the Upper Spray Spray Arms Container for Salt Container for Rinse Aid Detergent Dispenser Rating Filters Plate...
Control panel Water sof- Function Multi-display tener button button Wash programme buttons Control indicator Door handle Water softener and function button: In addition to the wash pro- gramme marked, it is also possible to adjust the dishwasher's water sof- tener using a combination of these buttons. The 3 lights of the multi-display can display: –...
Operating Instructions Prior to using for the first time Prior to using for the first time, remove all the clips with which the dish racks are secured for transport. Then perform the following steps: 1. Adjust the water softener 2. Fill with Salt for the Water Softener 3.
Page 11
It is only possible to adjust the water hardness setting when a pro- gramme is not running. If you have inadvertently started a programme (an LED indicator is constantly illuminated), then the programme must be cancelled by pressing the appropriate button. 1.
Operating Instructions Filling with Salt for the Water Softener Use only salt designed for dishwashers. Never fill the salt container with any another type of salt (e.g. culinary salt) or dishwasher deter- gent as this would irreparably damage the water softener. Prior to filling with salt, please check each time that you really do have a packet of dishwasher salt in your hand.
Filling with Rinse Aid Rinse aid is automatically added during the last rinse, ensuring thor- ough rinsing, spot and streak free drying. Only use rinse aid specifically designed for domestic dishwashers. Never fill the rinse aid container with any other substance as this would dam- age the appliance.
Operating Instructions Adjusting Rinse Aid Dosing As the dishes are washed rinse aid is released from the dispenser into the wash water. The dose is factory set at 4, and can be adjusted from 1 to 6. Only change the setting if streaks, milky spots or dried on water marks are visible on glasses or crockery.
In Daily Use • Check the salt and rinse aid levels. • Load cutlery and dishes into the dishwasher • Fill with dishwasher detergent • Select a wash programme suitable for the cutlery and dishes • Start the wash programme Loading Cutlery and Dishes Sponges, household cloths and any object that can absorb water should not be washed in the dishwasher...
Operating Instructions – To avoid damage to glasses, they must not touch – Do not lay small objects (e.g. lids) in the cutlery rack Loading Cutlery Long bladed knives stored in an upright position are a potential haz- ard. Long and/or sharp items of cutlery such as carving knives must be posi- tioned horizontally in the upper bas- ket.
Loading Pans, Frying Pans and Large Plates Load large and heavily soiled dishes in the lower rack. To ease the loading of large items at some dishwasher-models the two rows of prongs for the right-hand plate insert can be folded down: 1.
Operating Instructions Loading Cups, Glasses and Coffee Services Load small, delicate items and long pointed cutlery in the upper rack. • Arrange items of crockery on the folding cups racks so that they are offset from each other and water can reach all items.
Filling with Detergent Only use dishwasher detergent. Fill with detergent: – Prior to the start of a wash programme (not for the pre wash pro- gramme). The detergent is released into the wash water during the programme. Please observe the manufacturer's dosing and storage recommenda- tions as stated on the detergent packaging.
Operating Instructions Bio Wash Programmes and Concentrated Detergents Based on their chemical composition, dishwasher detergents can be split into two basic types: – Conventional, alkaline detergents with caustic components – Weak alkaline concentrated detergents with natural enzymes. The use of BIO wash programmes in conjunction with concentrated detergents reduces pollution and is good for your dishes;...
Selecting the Wash Programme (Programme Table) Choose the most suitable wash programme with the aid of this table: Type of Dinner service and cooking utensils dishes in addition Type of • heavily soiled soiling • dried on left- overs, particu- larly egg white and thickeners ò...
Operating Instructions Start the wash programme 1. Check that when the dishes and cutlery are loaded in the dishwasher the spray arms are free to rotate. 2. Open the water tap fully. 3. Shut the door. 4. Press the ON/OFF button. ON/OFF button indicator comes on. 5.
Pause function The pause function can only be initiated before the drying section of the programme I.. If the pause function is initiated during the drying section of the programme I the wash programme is ended. Using the pause function the dishwasher can be temporarily stopped: 1.
Operating Instructions Care and Cleaning Do not under any circumstances use furniture care products or aggres- sive cleaners. • If necessary, clean the controls only with a soft cloth and pure warm water. • Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary.
Page 25
7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clock- wise to the stop. During this process ensure that the flat filter does not protrude above the base of the wash- ing compartment.
If the fault is displayed again, contact your local AEG Service Force Centre. • If other lights flash in the multi-display, please contact your local AEG Service Force Centre stating which fault indicator is flashing. Symptom: The top light in the multi- display is flashing.
...there are problems operating the dishwasher. Symptom The programme does not start. Spots of rust are visible in the washing com- partment. There is a whistling noise during washing..the wash results are unsatisfactory. The dishes are still dirty. – The wrong wash programme was selected. –...
Operating Instructions There are streaks, milky spots or a bluish coating on glasses and dishes. – Decrease rinse aid dosing. There are dried water drops on the glasses and dishes. – Increase rinse aid dosing. – The detergent may be the cause. Contact the detergent manufac- turer's consumer advisor.
Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme (see Programme Table). Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see Programme Table).
Installation and Connection Instructions INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher • The dishwasher must be installed on a firm floor and adjusted such that it is stable and level. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by unscrew- ing:...
Dishwashers That Can Be Integrated (see installation template supplied) The door of the appliance can be fitted with a wooden/facing panel with the following dimensions: Width: 591 – 594 mm Thickness: 16 – 24 mm Height: dependent on (variable) Weight: max.
Installation and Connection Instructions Connecting the Dishwasher Water Connection The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations. • The dishwasher must be connected to a cold water supply. •...
The following section is only applicable to dishwashers that have a safety valve on the threaded hose fitting for the tap: Water inlet hose with safety valve After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running.
– Minimum required height 40 cm above the lower edge of the machine. Extension hoses • Extension hoses are available from AEG Service Force. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded.
Installation and Connection Instructions Leak Prevention System For protection from damage due to water leaks, the dishwasher is equipped with a leak prevention system, the AQUA CONTROL SYSTEM. In the event of a fault, the safety valve immediately interrupts the sup- ply of water to the appliance and the drain pump switches on.
Installation and Connection Instructions Electrical Connection Any electrical work required to install this appliance should be car- ried out by a qualified electrician or competent person. WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed.
Connections The water inlet and drain hoses, as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance. The plumbing and electrical installation example given below can only be regarded as a recommendation. Two 45°...
3. Should guarantee repairs be necessary the purchaser must inform the nearest customer service office (manufacturer´s service or authorised agent). AEG reserves the right to stipulate the place of the repair (i. e. the customer´s home, place of installation or AEG workshop).
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls. Customer Care For general enquiries concerning your AEG appliance or for further information on AEG products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.aeg.co.uk.