Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Eastsign BU-1600WL
Summary of Contents for Eastsign BU-1600WL
- Page 1 SMSLIQ20190312-R1 Eastsign LiquidLaminator UserManual Eastsign...
-
Page 2: Table Of Contents
Eastsign Content Chapter1.Introduction------------------------------------------------------------01 Chapter2.Specifications--------------------------------------------------------- 02 Chapter3.MachineStructure---------------------------------------------------- 03 Chapter4.ControlPanelInstruction------------------------------------------- 04 Chapter5.Operatingprocedures----------------------------------------------- 0 6 Chapter6.MaintenanceandCautions-------------------------------------------10 Chapter7.Warranty----------------------------------------------------------------11 Limitationofliability---------------------------------------------------------------12 Contactus----------------------------------------------------------------------------13... -
Page 3: Chapter1.Introduction
Eastsign Chapter1.Introduction Liquid laminator is one kind of machine, which we use to apply special emulsifiedliquidtocoatonthesurfaceofprintingsurface,afterdrying,a protectivefilmwillbeformedonthesurfaceofthepicture. Itiswidelyusedinthepost-productionofoutdoor/indooradvertisement andvehiclebodyadvertisement.Theliquidfilmisformeddirectlyonthe picture surface, the spaces between molecules reduced greatly, and affixedfirmly.Itisimpossibletodepartthefilmfromthepicture. This kind of machine can be used to laminate the picture with broad widths,eitherstandardwidepictureornon-standardwidepicture,notbe limited to the widths of general film. The picture will show more bright-... -
Page 4: Chapter2.Specifications
Eastsign Chapter2. Specifications Model K m bc j BU -1600WL BU -2200WL BU -3300WL Working Width 1580mm 2140mm 3240mm Laminating speed 1.5m/min Coating thickness 0.007-0.01mm Laminating temperature . + /3. Motor power Heating power 6500W 1 Phase/220V, 3 Phase/380V Power supply... -
Page 5: Chapter3.MachineStructure
Eastsign Chapter3.MachineStructure Fig.1FrontView Fig.2BackView Fig.3Rightandleft... -
Page 6: Chapter4.ControlPanelInstruction
Eastsign Chapter4.ControlPanelInstruction 4.1、 Heater Control Switch: Press the “ON” at the upper position of the switch, it will start to heat up, and the indicator lamp will turn on; at the same time, the cooler over the drying oven begin to work. Press the “OFF”... - Page 7 Eastsign Fig.4 Control panel Fig.5 Temp. controller...
-
Page 8: Chapter5.OperatingProcedures
Eastsign Chapter5.Operatingprocedures 5.1、 Preparation 5.1.1、 AddingLiquid:Turnofftheliquidpumpswitch.Openthemachine left cabinet door. Add some liquid filtered into tank depending upon the amount to be used. (It is permitted to add 5-10% clean waterandstirringthemixedliquid.Seeliquidfilminstructionfor details.) 5.1.2、 Temperature Setting: Turn on the main switch (see Fig.2). Press the △ button or the ▽ button to set temperature. Because liquid... - Page 9 Eastsign 5.2、 PlacingPictureonthemachine 5.2.1、 Paste a piece of leading paper (or cloth) about 1-1.5 meters long andhavingthesamewidthwiththepicture(itisbettertousesame material with the picture.) at each end of the picture to be laminated. Then roll the picture on a paper tube with the picture drawing outward. After this, put the paper tube into the roller for...
- Page 10 Eastsign time,theaxialfanisstillworkingtoreducethetemperatureinside the heating-boxes and drying the liquid in the guiding paper (or cloth).Notice:Aftertheheating-boxesstopwork,theaxialfanwill stop work automatically after 2 minutes delayed. Please turn off themainswitchaftertheaxialfanstopswork. 5.4.4、 Take the picture from the machine: Lift up the heating-boxes, depart the picture from the guiding paper (or cloth). Press the Direction Switch of the roller for collecting picture (Fig.4) at...
- Page 11 Eastsign 5.3、 Pre-heating Pullthehandlesontheheating-boxes,andmaketheheatingoven turn over upward. Press the“ ON” at the upper position of Heater Control Switch, the indicator will be on, the axial fan of the drying oven will start to work. There is hot wind from the bottom of the drying oven, and the drying oven will pre-heat for about 3-8 minutes.Themachinestartstoworkwhenthesettingtemperature...
-
Page 12: Chapter6.MaintenanceAndCautions
Eastsign Chapter6.MaintenanceandCautions 6.1、 Connectthepowersupplywellandtheearthwireespecially. 6.2、 The power supply will be turned off when pressing the emergency switch. If you want to continue to work, you need to turn on the power supply again. Therefore, please don't touch the emergency switchduringworkinordertoavoiddamageloss. -
Page 13: Chapter7.Warranty
7.4、 Onlyinurgentcases,whentheoperationalsafetyisriskedand/orwhenthereis a fear of any disproportionate claims, which shall be immediately notify to Eastsign, the Buyer is entitled to remedy the defect on its own or by third parties, and it shall demand to Eastsign the reimbursement of expenses incurredforthispurpose.... -
Page 14: LimitationOfLiability
Eastsign Limitationofliability 7.9、 Eastsign is not liable for any damaging consequences resulting from the executionofrepairsontheMachinerywithoutitspriorapproval,executedby theBuyerorbyathirdparty. 7. 10 、 Thewarrantydoesnotapply,forexamplebutnotlimitedto:topartssubjectto normal wear; to damages caused by improper or inadequate maintenance, incorrect positioning, incorrect operations of the Buyer's personnel, use of incorrect raw materials, faulty or careless treatment, overexploitation of the devices;touseinanyapplicationotherthanthatforwhichitwasintended;to... -
Page 15: Contact
Eastsign Contactus Eastsign International Ltd Hong Kong Headquarter Rm 1818,18/F., Shatin Galleria,18-24 Shan Mei Street, Fotan, N.T., Hong Kong T e l :+852 2117 0098 info@eastsign.com Eastsign International Ltd Shenzhen Branch 28I, Tower C, Lvgem Square, 6009 Shennan Avenue, Futian District, Shenzhen, China Te l :+86 755 8296 8521 info@eastsign.com...
Need help?
Do you have a question about the BU-1600WL and is the answer not in the manual?
Questions and answers