Download  Print this page

Oven Installation; Ventilation System; Mounting Plate - Frigidaire GLMV169D Installation Instructions Manual

Over the range microwave oven
Hide thumbs

Advertisement

Table of Contents
Exhaust Damper
Assembly
Tapping Screw

8 VENTILATION SYSTEM

(PREPARING OVEN FOR INSTALLATION)
(C) VERTICAL EXHAUST: OUTSIDE VENTILATION
1. Remove and save 2 screws from back edge and 1 screw
from the top center of the Fan Cover Bracket. Remove Fan
Cover Bracket by sliding it in the opposite direction of the
arrow on the Fan Cover Bracket as shown in Figure 8.
2. Withdraw Hood Fan Unit carefully and slip wires out of Wire
Box. See Figure 9.
CAUTION: Do not pull or stretch hood fan wiring.
3. Turn the Hood Fan Unit end-over-end. Rotate the Hood Fan
Unit 90˚ so that the fan blade openings are facing upward.
Replace Hood Fan Unit into the oven. Be careful not to pinch
the lead wire between the inner bracket and the Hood Fan
Unit. See Figure 13.
4. Put the lead wire into Wire Box. See Figure 13.
5. Replace the Fan Cover Bracket by sliding it into the slits in
the same direction as the arrow on the Fan Cover Bracket.
Make sure the fan blades are visible through the top open-
ings in the oven before proceeding. Attach the Fan Cover
Bracket to unit with 3 screws, which were removed in Step 1
above. See Figure 11. The Hood Fan Unit is now rotated for
vertical exhaust operation.
6. Attach the Exhaust Damper Assembly to the fan cover on the
top of the outercase cabinet after mounting the oven. To
attach the Exhaust Damper Assembly, refer to MOUNTING
OVEN TO THE WALL, page 6.
Installation Instructions
Figure 11

Mounting Plate

(Back Side)
Figure 12
Rotate 90˚

9 OVEN INSTALLATION

THIS OVEN CANNOT BE PROPERLY INSTALLED WITHOUT
REFERRING TO THE MOUNTING INSTRUCTIONS FOUND
ON BOTH TEMPLATES.
THE NEXT STEP IS TO READ AND FOLLOW MOUNTING
INFORMATION ON BOTH TOP CABINET AND WALL TEM-
PLATES.
NOTE: THIS OVEN SHOULD BE ATTACHED TO AT LEAST
ONE WALL STUD.
MOUNTING PLATE
1. Separate 4 Toggle Bolts, packed in the INSTALLATION
cont.
HARDWARE, from the Toggle Nuts.
2. Use wood screws to attach mounting plate to the stud or
studs. Use Toggle Bolts to attach mounting plate through the
holes at A, B, C and D UNLESS THOSE HOLES ARE
LOCATED ON THE STUD. Insert one Toggle Bolt into A, B,
C and D where appropriate (these correspond to holes of the
Wall Template) and put the Toggle Nuts onto the Toggle
Bolts. Figure 14.
Refer to instructions in Wall Template.
3. Position the Mounting Plate with the Toggle Bolts attached at
the wall location and insert Toggle Nuts and Bolts through
the holes in the wall with the Toggle Nuts closed. Figure 15.
Use Wood Screws to attach the Mounting Plate to studs.
NOTE: Before insertion, be sure you leave a space more
than the thickness of the wall between the Mounting Plate
and the end of each of the Toggle Nuts (in the closed posi-
tion). If you do not leave enough space, the Toggle Nut will
not be able to open on the other side of the wall. Also, once
a Toggle Nut opens, it cannot be withdrawn from the hole;
therefore make sure all of the Toggles are in the correct posi-
tion before insertion.
4. Align the Mounting Plate carefully and hold in position while
tightening Toggle Bolts. Pull Toggle Bolt toward you and turn
clockwise to tighten. Figure 16.
5
Figure 13

Hide quick links:

Advertisement

Table of Contents
loading

  Also See for Frigidaire GLMV169D

  Related Manuals for Frigidaire GLMV169D