Download
Share
Print this page
Torque XCREATE-LPDWM Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Torque Manuals
  4. Fitness Equipment
  5. XCREATE-LPDWM
  6. Assembly instructions manual

Torque XCREATE-LPDWM Assembly Instructions Manual

4 ft 1.2 m lat pulldown wall mount
Hide thumbs Also See for XCREATE-LPDWM:

Advertisement

Quick Links

Download this manual
ASSEMBLY INSTRUCTIONS
4 FT (1.2 M) LAT PULLDOWN WALL MOUNT
VERSION: XCREATE-LPDWM
PART # 5701101-A

Advertisement

loading
Need help?

Need help?

Do you have a question about the XCREATE-LPDWM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Torque XCREATE-LPDWM

Summary of Contents for Torque XCREATE-LPDWM

  • Page 1 ASSEMBLY INSTRUCTIONS 4 FT (1.2 M) LAT PULLDOWN WALL MOUNT VERSION: XCREATE-LPDWM PART # 5701101-A...
  • Page 2 NOTE: ITEM PART NUMBER DESCRIPTION Anchoring hardware is dictated by the wall construction that the station 56641PA PTD ASSY, LOWER WALL MOUNT is being attached to. See pages 4 and 13 for the requirements. 5645301 WLDMT, LAT BASE 2001301 WASHER, FLAT 1/2 SAE ST ZN If multiple stations are going to be attached to the same wall, a minimum 2006803 BOLT, 1/2-13 X 1"...
  • Page 3 STEP 1 LOWER WALL MOUNT LAT BASE 1/2 X 1" BOLT (2) 1/2" FLAT WASHER NOTE: BEFORE TIGHTENING BOLTS, MAKE SURE THAT THESE TWO SURFACES ARE FLUSH NOTES: SECURELY tighten bolt connections in this step.
  • Page 4 STEP 2 WALL LOWER WALL MOUNT 3/8" FLAT WASHER (4) NOTE: BASE PLATE BEFORE ANCHORING LOWER WALL 3/8" LAG BOLT (4) MOUNT TO THE WALL, ADJUST (TYPICAL FOR LEVELERS (2) SO THAT THE BASE WOOD STUDS) PLATE IS LEVEL WITH THE FLOOR. NOTE: MAKE SURE THE LOWER 2-1/2"...
  • Page 5 STEP 3 LOWER WALL MOUNT 3/8" FLAT WASHER (2) 3/8 X 4-3/4" BOLT (2) LAT BASE NOTES: SECURELY tighten bolt connections in this step.
  • Page 6 STEP 4 LOWER WALL MOUNT 3/8" X 3/4" BOLT (2) 3/8" FLAT WASHER (2) LEFT SHROUD BASE NOTES: SECURELY tighten bolt connections in this step.
  • Page 7 STEP 5 LOWER WALL MOUNT 3/8 X 3/4" BOLT (2) 3/8" FLAT WASHER (2) RIGHT SHROUD BASE NOTES: SECURELY tighten bolt connections in this step.
  • Page 8 STEP 6 LAT FRONT UPRIGHT 1/2 X 4" BOLT (2) 1/2" FLAT WASHER (4) LAT BASE 1/2" LOCK NUT (2) NOTES: LOOSELY tighten bolt connections in this step.
  • Page 9 STEP 7 GUIDE ROD RETAINER (2) SHAFT COLLAR (2) GUIDE ROD (2) HEAD PLATE 15 LB WEIGHT PLATE (10) 20 LB WEIGHT PLATE (5) WEIGHT STACK CUSHION (2) NOTE: INSERT GUIDE RODS THROUGH THE LAT BASE AND DOWN TO TOP OF BOLTS LAT BASE...
  • Page 10 STEP 8 3/8 X 3/4" BOLT (2) WEIGHT SELECTOR STORAGE PLATE HEAD PLATE NOTES: SECURELY tighten bolt connections in this step.
  • Page 11 STEP 9 LAT TOP BOOM 1/2 X 1" BOLT (2) UPPER WALL MOUNT 1/2" FLAT WASHER (2) NOTES: SECURELY tighten bolt connections in this step.
  • Page 12 STEP 10 LAT TOP BOOM 1/2" FLAT WASHER (2) 1/2 X 1" BOLT (2) LAT FRONT UPRIGHT NOTES: LOOSELY tighten bolt connections in this step.
  • Page 13 STEP 11 UPPER WALL MOUNT 3/8" FLAT WASHER (4) NOTE: MAKE SURE THE UPPER 3/8" LAG BOLT (4) WALL MOUNT IS LEVEL 16" (TYPICAL FOR (40.6 CM) WOOD STUDS) WARNING: THE UPPER WALL MOUNT MUST BE 2-1/2" ANCHORED TO THE WALL USING FOUR (6.4 CM) WALL ANCHORS SUITABLE FOR THAT PATICULAR WALL CONSTRUCTION...
  • Page 14 STEP 12 GUIDE ROD RETAINER (2) NOTE: SLIDE THE GUIDE ROD RETAINERS UP INSIDE THE LAT TOP BOOM LAT TOP BOOM. SLIDE THE SHAFT COLLARS UP INSIDE OF THE GUIDE ROD RETAINERS AND SECURELY TIGHTEN THE SET SCREWS OF THE SHAFT COLLARS SECURELY TIGHTEN THIS BOLT CONNECTION SHAFT COLLAR (2)
  • Page 15 STEP 13 SWIVEL STORAGE FOR WEIGHT PULLEY STACK SELECTOR PIN HOUSING THREADED END NOTE: THE HOUSING ON THE CABLE SHOULD BE AT JAM NUT LEAST 1/2" AWAY FROM THE SWIVEL PULLEY. IF THE HOUSING IS TOUCHING THE SWIVEL HEAD PLATE PULLEY, THEN THE CABLE NEEDS TO BE ADJUSTED.
  • Page 16 STEP 14 LAT FRONT UPRIGHT SPRING PIN HOLE 1/2" FLAT 1/2 X 5-1/2" BOLT WASHER (2) KNEE HOLD DOWN NOTE: PULL SPRING PIN OUT TO ASSEMBLE THE KNEE HOLD DOWN. RELEASE THE SPRING PIN INTO THE DESIRED HOLE 1/2" LOCK NUT ON THE LAT FRONT UPRIGHT NOTES: SECURELY tighten bolt connections in this step.
  • Page 17 STEP 15 TAPERED SEAT 3/8" FLAT WASHER (2) 3/8" X 1-1/4" BOLT (2) LAT BASE NOTES: SECURELY tighten bolt connections in this step.
  • Page 18 STEP 16 NOTE: NOTE: MAKE SURE SHROUD IS MAKE SURE SHROUD IS SEATED BETWEEN THE SEATED BETWEEN THE SHROUD SUPPORT AND SHROUD SUPPORT AND THE FOUR TABS AS SHOWN THE FOUR TABS AS SHOWN. TOP VIEW LEFT TOP VIEW RIGHT RIGHT SHROUD BASE FRONT SHROUD (2) LEFT SHROUD BASE...
  • Page 19 STEP 17a 1/4 X 1/2" BOLT (4) 1/4" FLAT WASHER (4) TOP CAP NOTE: MAKE SURE INTERNAL GROOVES OF THE TOP CAP FIT DOWN OVER THE TOP EDGES OF BOTH FRONT SHROUDS. UPPER WALL MOUNT FRONT SHROUD (LEFT SIDE) FRONT SHROUD (RIGHT SIDE) NOTES: LOOSELY tighten bolt connections in this step.
  • Page 20 STEP 17b 1/4 X 1/2" BOLT (2) 1/4" FLAT WASHER (2) TOP BOOM TOP CAP NOTES: SECURELY tighten bolt connections in this step, and previous step.
  • Page 21 STEP 18 NOTE PLACARD CENTER PLACARD ON SHROUD SURFACE FRONT SHROUD (RIGHT SIDE) 57-1/2" (146 CM) 2-1/4" (5.7 CM)
  • Page 22 STEP 19 1/4 X 3/8" BOLT (2) 1/4" FLAT WASHER (2) FRONT BASE COVER LAT BASE NOTES: SECURELY tighten bolt connections in this step.
  • Page 23 STEP 20 LAT BAR SNAP HOOK...

  • Page 24: Maintenance

    MAINTENANCE GUIDE RODS: Clean and lubricate with a silicone or teflon based lubricant INSPECTION: Once a month, check for loose bolts. Tighten if necessary. CABLES: Check tension, end fitting and cable coating. Replace if damage or worn. (NOTE: NEW CABLES ALWAYS STRETCH DURING USE.